Characteristics of nonlinear response of deep saturated soil deposits

1997 ◽  
Vol 87 (2) ◽  
pp. 342-355 ◽  
Author(s):  
Shean-Der Ni ◽  
Raj V. Siddharthan ◽  
John G. Anderson
Keyword(s):  
Resonant Frequency ◽  
Soil Properties ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Saturated Soil ◽  
Soil Conditions ◽  
Base Excitation ◽  
Soil Deposits ◽  
Stress Dependent

Abstract Recent EPRI seismic design guidelines call for dynamic soil properties (shear modulus ratio and damping) and liquefaction strength curves to be characterized as a function of the effective vertical stress (or depth). A modified version of the DESRA2 constitutive model for saturated soil has been applied to study the nonlinear seismic response including liquefaction of medium dense soil deposits of various thicknesses. The results of the stress-dependent soil properties model show lower deamplification and higher first-mode (resonant) frequency than that of the stress-independent soil properties model. By using the stress-dependent model with impulse base excitation, the nonlinear behavior of various soil deposits has been investigated under a variety of conditions. The results show that (1) the saturated soil deposit has a smaller surface amplitude and significantly lower resonant frequency than the unsaturated soil deposit of the same thickness; (2) for the saturated soil conditions, the larger the base excitation, the lower the surface amplification and the resonant frequency; (3) the deep soil deposits show lower surface amplification and resonant frequency compared to the response of shallow deposits; (4) when shallow and deep deposits are compared, the shallow deposits develop much higher residual pore-water pressure; and (5) the amplification and residual pore-water-pressure response of deposits deeper than 100 m or so are very similar. The application of the method has also been illustrated using a strong synthetic base excitation applied to the base at a site near Reno. The results in general are consistent with those computed using the impulse loading. The study reveals that the response predicted from the conventionally used stress-independent soil properties model is unconservative for deep deposit.

scholarly journals Numerical Evaluation of The Nonlinear Behavior of Soil-Pile Interaction Under The Effect of Coupled Static-Dynamic Loads

2021 ◽  
Author(s):  
Duaa Al-Jeznawi ◽  
ISMACAHYADI Mohamed Jais ◽  
Bushra S. Albusoda
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Three Dimensional ◽  
Ground Surface ◽  
Frictional Resistance ◽  
Saturated Soil ◽  
Shaking Table ◽  
Physical Models ◽  
Soil Layers

Abstract Liquefaction of saturated soil layers is one of the most common causes of structural failure during earthquakes. Liquefaction occurs as a result of increasing pore water pressure, whereby the rise in water pressure occurs due to unexpected change in stress state under short-term loading, i.e., shaking during an earthquake. Thus, general failure occurs when the soil softens and eliminates its stiffness against the uplift pressure from the stability of the subsurface structure. In this case, the condition of soil strata is considered undrained because there is not enough time for the excess pore water pressure to dissipate when a sudden load is applied. To represent the non-linear characteristics of saturated sand under seismic motions in Kobe and Ali Algharbi earthquakes, the computational model was simulated using the UBCSAND model. The current study was carried out by adopting three-dimensional-based finite element models that were evaluated by shaking table tests of a single pile model erected in the saturated soil layers. The experimental data were utilized to estimate the liquefaction and seismicity of soil deposits. According to the results obtained from the physical models and simulations, this proposed model accurately simulates the liquefaction phenomenon and soil-pile response. However, there are some differences between the experiment and the computational analyses. Nonetheless, the results showed good agreement with the general trend in terms of deformation, acceleration, and liquefaction ratio. Moreover, the displacement of liquefied soil around the pile was captured by the directions of vectors generated by numerical analysis, which resembled a worldwide circular flow pattern. The results revealed that during the dynamic excitation, increased pore water pressure and subsequent liquefaction caused a significant reduction in pile frictional resistance. Despite this, positive frictional resistance was noticed through the loose sand layer (near the ground surface) until the soil softened completely. It is worth mentioning that the pile exhibited excessive settlement which may attribute to the considerable reduction, in the end, bearing forces which in turn mobilizing extra end resistance.

scholarly journals The Evolution of Pore Water Pressure in a Saturated Soil Layer between Two Draining Zones by Analytical and Numerical Methods

2015 ◽  
Vol 05 (04) ◽  
pp. 390-398
Author(s):  
Abib Tall ◽  
Cheikh Mbow ◽  
Daouda Sangaré ◽  
Mapathé Ndiaye ◽  
Papa Sanou Faye
Keyword(s):  
Numerical Methods ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Layer ◽  
Saturated Soil

Investigation of field-installation effects of horizontal twin-jet grouting in Shanghai soft soil deposits

2013 ◽  
Vol 50 (3) ◽  
pp. 288-297 ◽  
Author(s):  
Zhi-Feng Wang ◽  
Shui-Long Shen ◽  
Chu-Eu Ho ◽  
Yong-Hyun Kim
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Ground Surface ◽  
Prediction Methods ◽  
Jet Grouting ◽  
Soil Deposits ◽  
Lateral Displacements ◽  
Surface Heave

This paper presents a case study of an investigation into the responses of the surrounding ground to the horizontal twin-jet grouting method (HTJGM) in soft soil deposits of Shanghai. During the field test, the variation of pore-water pressure, lateral earth pressure, lateral displacements of the subsurface soils, and ground surface heave induced by the installation of five horizontal jet-grouted columns were monitored. The monitoring results indicate that the excess pore-water pressure reached 4 to 6 times the undrained shear strength of the soils, while maximum lateral displacements and ground surface heave were up to 80 and 17 mm, respectively. The influence range due to the installation of jet-grouted columns was between 15 and 20 times the nominal column radius. The development of prediction methods for lateral displacements and ground surface heave induced by the HTJGM installation process are presented and discussed. Results from the investigation suggest that the proposed prediction methods can be used to provide reasonable estimates of ground response and influence range of horizontal jet grouting.

Analysis of One-Dimensional Thermal Consolidation of Saturated Soil with and without Thermo-Mechanical Coupling

2012 ◽  
Vol 594-597 ◽  
pp. 335-338
Author(s):  
Xue Shen ◽  
Rui Qian Wu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Saturated Porous Medium ◽  
Water Pressure ◽  
Saturated Soil ◽  
Excess Pore Water Pressure ◽  
One Dimensional ◽  
Mechanical Coupling ◽  
Thermal Consolidation ◽  
Excess Pore

Based on a one-dimensional thermal consolidation formulation with and without thermo-mechanical coupling of saturated porous medium, problems of one-dimensional thermal consolidation of saturated soil were investigated. For the condition with instantaneous constant surface temperature and uniform initial pore-pressure, analytical solutions of excess pore-water pressure and temperature increment were derived respectively by the method of finite Fourier transform and inverse transform. A relevant computer program was developed, and the excess pore-water pressure was compared in detail. The results show that the thermo-mechanical coupling item in the thermal consolidation equation can be ignored.

Numerical study of soil conditions under which matric suction can be maintained

2004 ◽  
Vol 41 (4) ◽  
pp. 569-582 ◽  
Author(s):  
L L Zhang ◽  
D G Fredlund ◽  
L M Zhang ◽  
W H Tang
Keyword(s):  
Steady State ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Storage ◽  
Matric Suction ◽  
Rainfall Infiltration ◽  
Soil Conditions ◽  
Soil System ◽  
Coefficient Of Permeability

The effect of negative pore-water pressure is often ignored in slope stability studies. There is a perception among geotechnical engineers that negative pore-water pressures will dissipate with rainfall infiltration and cannot be relied upon in design considerations. The objective of this paper is to illustrate that under certain conditions soil suction can be maintained. Based on the theory of infiltration and seepage through a saturated–unsaturated soil system, steady state and transient finite element seepage analyses were conducted using Seep/W on a 20 m high slope inclined at 30°. The results of the analysis showed that under steady state conditions, the most important factor influencing the permanency of matric suction in the soil is the magnitude of rainfall flux expressed as a percentage of the saturated coefficient of permeability of soil. For the analysis under transient seepage conditions, the results showed that the pore-water pressure profile depends on the magnitude of the rainfall flux, the saturated coefficient of permeability, the soil-water characteristic curve, and the water storage function. For a soil with a low coefficient of permeability and a large water storage capacity, the matric suction needs a substantial amount of time to dissipate and thus may be maintained over a longer time period than the rain is likely to fall, even if the ground surface flux is equal to or greater than the saturated coefficient of permeability. Engineers should address more appropriate engineering design assumptions that can be related to the permanence of matric suction in soil slopes based on the numerical analysis. Measures such as slope cover or surface recompaction can be taken into consideration to minimize the rainfall infiltration and thus maintain active matric suction in slopes.Key words: unsaturated soils, slope, rainfall infiltration, matric suction, permeability.

Analysis of One-Dimensional Thermal Consolidation for Saturated Soil Considering Different Permeabilities

2014 ◽  
Vol 919-921 ◽  
pp. 641-644
Author(s):  
Cai Xia Guo ◽  
Rui Qian Wu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Saturated Soil ◽  
Excess Pore Water Pressure ◽  
One Dimensional ◽  
Consolidation Theory ◽  
Thermal Consolidation ◽  
The One ◽  
Excess Pore

Based on the analytical solutions of pore-water pressure and settlement. Problems of the one-dimensional thermal consolidation of saturated soil considering three different permeabilities were analyzed. Aiming at each permeability of thermal consolidation theory, compared with the corresponding Terzaghis consolidation theory, the one-dimensional thermal consolidation behaviour of saturated soil was analyzed in terms of excess pore-water pressure, the settlement. The results show that the permeability plays an important role in the thermal consolidation. The more permeability, the quicker pore-water pressure dissipation and the rate of settlement. Settlement of ground is more sensitive to temperature condition than the excess pore-water pressure. The behaviour of excess pore-water pressure in the process of thermal consolidation is very similar to the corresponding Terzaghis theory.

scholarly journals Empirical and Physically Based Thresholds for the Occurrence of Shallow Landslides in a Prone Area of Northern Italian Apennines

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2653 ◽  
Author(s):  
Massimiliano Bordoni ◽  
Beatrice Corradini ◽  
Luca Lucchelli ◽  
Roberto Valentino ◽  
Marco Bittelli ◽  
...  
Keyword(s):  
Pore Water ◽  
Hydrological Modeling ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shallow Landslides ◽  
Soil Conditions ◽  
Primary Role ◽  
Slope Failures ◽  
Hydrological Conditions ◽  
Italian Apennines

Rainfall thresholds define the conditions leading to the triggering of shallow landslides over wide areas. They can be empirical, which exploit past rainfall data and landslide inventories, or physicallybased, which integrate slope physical–hydrological modeling and stability analyses. In this work, a comparison between these two types of thresholds was performed, using data acquired in Oltrepò Pavese (Northern Italian Apennines), to evaluate their reliability. Empirical thresholds were reconstructed based on rainfalls and landslides triggering events collected from 2000 to 2018. The same rainfall events were implemented in a physicallybased model of a representative testsite, considering different antecedent pore-water pressures, chosen according to the analysis of hydrological monitoring data. Thresholds validation was performed, using an external dataset (August 1992–August 1997). Soil hydrological conditions have a primary role on predisposing or preventing slope failures. In Oltrepò Pavese area, cold and wet months are the most susceptible periods, due to the permanence of saturated or close-to-saturation soil conditions. The lower the pore-water pressure is at the beginning of an event, the higher the amount of rain required to trigger shallow failures is. physicallybased thresholds provide a better reliability in discriminating the events which could or could not trigger slope failures than empirical thresholds. The latter provide a significant number of false positives, due to neglecting the antecedent soil hydrological conditions. These results represent a fundamental basis for the choice of the best thresholds to be implemented in a reliable earlywarning system.

scholarly journals Influence and evaluation of saturated soil shield construction on existing highway

2020 ◽  
Author(s):  
Liuqi Xu ◽  
Chongfu Wu ◽  
Liwei Wang ◽  
Shuangjun Xu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Saturated Soil ◽  
Vertical Deformation ◽  
Engineering Project ◽  
Initial Displacement ◽  
Tunnel Excavation ◽  
The Road ◽  
Side Friction

Abstract In order to study the shield construction under an existing highway, the initial displacement and the excess pore water pressure solution from Biot consolidation equation were used to derive the analytical solutions of the vertical deformation and pore water pressure of saturated soil caused by the frontal friction and side friction of the cutterhead. In addition, by introducing the layered method and combining it with other theoretical analytical equations, the expressions of total vertical deformation and total pore water pressure caused by tunnel excavation with different overlying materials were obtained. The simulation results on an engineering project showed that the angle α between the direction of the road and the propulsion axis of the shield had a significant influence on the surface settlement of the road. When the angle α was increased, the settlement curve had higher variation; but the variation would not exceed the maximum settlement value above the shield axis. When the road was perpendicular to the shield axis, a critical point of the road bulging and settlement was formed above the incision. Due to the grinding resistance of the cutterhead, the pore water pressure under the roadbed was distributed asymmetrically on both sides of the shield axis.

Sign in / Sign up

Export Citation Format

Share Document