scholarly journals Synthesis and Characterization of Sr2CeO4 Phosphor Doped with Erbium

2010 ◽  
Vol 13 (1-2) ◽  
pp. 17
Author(s):  
K.V.R. Murthy ◽  
K. Suresh ◽  
B. Nageswara Rao ◽  
B. Walter Ratna Kumar ◽  
Ch. Atchyutha Rao ◽  
...  
Keyword(s):  
Rare Earth ◽  
Solid State ◽  
Sem Analysis ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rare Earth Ion ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Pl Emission

<p>The present paper reports the Photoluminescence (PL) of the Sr<sub>2</sub>CeO<sub>4</sub> phosphor, singly doped with Erbium rare-earth ion with different concentrations (0.01, 0.1, 0.2, 0.5 and 1%).The phosphor samples were synthesized using the standard solid state reaction technique. The effect of Er dopant on the structural, morphological, and Photoluminescent properties of the samples are studied with X-ray diffraction (XRD), PL and SEM analysis. The PL emission of undoped Sr<sub>2</sub>CeO<sub>4</sub> phosphor was observed at 470 nm with high intensity followed by the primary Er emissions with good intensity at 525, 530, 549, 557 and 565 nm.</p>

Solid State Synthesis and Characterization of Spintronics Material Cd0.55 Hg0.45 Te

2010 ◽  
Vol 44-47 ◽  
pp. 2299-2306
Author(s):  
H.M.Noor Ul Huda Khan Asghar ◽  
M. Asghar ◽  
M.S. Awan
Keyword(s):  
Solid State ◽  
Synthesis And Characterization ◽  
Chemical Analyses ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Cubic Crystal ◽  
X Ray ◽  
Edx Analyses ◽  
Scanning Electron

Polycrystalline spintronic material (Cd0.55Hg0.45Te) was synthesized by conventional solid state reaction. The samples ( = 5 mm and T = 1.5 mm) were prepared by uni-axial pressing. Samples were melted at 800°C for 3-2 hours. For chemical analyses, surface morphology and structural analyses, scanning electron microscopy (SEM) equipped with EDX system and X-ray diffraction studies were performed. XRD confirmed the cubic crystal structure. The Lattice constant of (Cd0.55Hg0.45Te) as determined by XRD was 0.6464 nm. The Miller indices (hkl) have been found by using crystallography method. The observed planes were (200), (210) and (331). The EDX analyses showed the typically compositions: Te 24.8% Cd 14.8% Al 5% and O2 46.4 % & C 9% (3 hours treatment) and Te 28.1% Cd 16% Al 4.1% and O2 39.3 %, Si 0.360% & C 12.1% (2 hours treatment) however we could not find any representative peak for Hg in all of the EDX analyses.

Synthesis and characterization of three new rare-earth orthoborates: Ba2MgY2(BO3)4, Ba2CdY2(BO3)4, and Ba2CdSc(BO3)3

2020 ◽  
Vol 49 (31) ◽  
pp. 10874-10879
Author(s):  
Runqing Liu ◽  
Hongping Wu ◽  
Hongwei Yu ◽  
Zhanggui Hu ◽  
Jiyang Wang ◽  
...  
Keyword(s):  
Rare Earth ◽  
High Temperature ◽  
Solution Method ◽  
Synthesis And Characterization ◽  
High Temperature Solution ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Solution ◽  
First Time

Three rare-earth orthoborates Ba2MgY2(BO3)4, Ba2CdY2(BO3)4, and Ba2CdSc(BO3)3 were synthesized via a high-temperature solution method and their structures were determined by single crystal X-ray diffraction for the first time.

Synthesis and Characterization of o-Carboranylthioether Derivatives

2011 ◽  
Vol 66 (9) ◽  
pp. 947-952
Author(s):  
Meiling Xu ◽  
Yong Nie ◽  
Jinling Miao ◽  
Zhenwei Zhang ◽  
Bin Peng ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Solid State ◽  
Single Crystal ◽  
Uv Light ◽  
Chloroform Solution ◽  
Alkyl Halides ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray

The reactions of the dithiolato-o-carborane salt (Et3NH)2(S2C2B10H10) (2) with alkyl halides BrCH2CH=CH2, BrCH2CH2CH2Cl and C6H5CH2Cl, afford the o-carboranyl-bisthioether derivatives 3a - c, which have been characterized by IR and NMR (1H, 13C, 11B) spectroscopy, mass spectrometry, and single-crystal X-ray diffraction (3c). The photoluminescent properties of the known compound 3c has been investigated. It exhibits a violet (chloroform solution) or blue (solid state) emission when excited with UV light.

Synthesis and Characterization of New Non-aromatic Texaphyrin-type Expanded Porphyrins

1999 ◽  
Vol 03 (02) ◽  
pp. 148-158 ◽  
Author(s):  
SYLVIE MEYER ◽  
MICHAEL C. HOEHNER ◽  
VINCENT LYNCH ◽  
JONATHAN L. SESSLER
Keyword(s):  
Schiff Base ◽  
Solid State ◽  
Good Yield ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Expanded Porphyrins ◽  
Meso Position ◽  
Macrocyclic Structure

The synthesis and X-ray diffraction-based characterization of a texaphyrin-type non-aromatic expanded porphyrin, 13,18,22,27-tetraethyl-14,17,23,26-tetramethyl-20-p-nitrophenyl-3,10,28,29,30,31-hexaazahexacyclo[23.2.1.04,9.112,15.116,19.121,24]untriaconta-2, 4, 5, 7, 10,12,14,16,18,-20,22,24(30),25,27-tetradecaene (1), is reported. This Schiff base macrocycle was prepared in good yield via the 1:1 HCl -catalyzed condensation of a tetrapyrrole dialdehyde precursor, (di(5-formyl-4,4'-diethyl-3,3'-dimethyl-2,2'-bipyrrole)-p-nitrophenylmethine), with 1,2-phenylenediamine. Compound 1 was assigned as being a 26 π-electron non-aromatic benzannulene on the basis of both proton NMR and single-crystal X-ray diffraction analyses. The latter studies, in particular, revealed a non-planar macrocyclic structure co-crystallized with a molecule of water. By varying either the diamine used in the cyclization step and/or the substituent in the meso-position of the tetrapyrrolic precursor, a range of other systems analogous to 1 could be obtained. The resulting systems were found to present good stability both in the solid state and in solution.

scholarly journals The effect of ligand-to-Eu3+ charge-transfer transitions (LMCT) on the photoluminescence intensity of M2SiO4: Eu3+ (M = Ca, Zn) type phosphors

2018 ◽  
Vol 36 (3) ◽  
pp. 509-513 ◽  
Author(s):  
Esra Öztürk ◽  
Erkul Karacaoglu
Keyword(s):  
Rare Earth ◽  
Solid State ◽  
Photoluminescence Intensity ◽  
Sintering Process ◽  
Secondary Phases ◽  
X Ray Diffraction ◽  
Rare Earth Ion ◽  
X Ray ◽  
Charge Transfer Transitions ◽  
The Eu

AbstractIn this study, silicate systems, M2SiO4 (M = Ca, Zn) were produced by solid state reaction and doped with 1 mol% Eu3+ rare-earth ion. Their heat treatments, which were conducted at 1200 °C and above for minimum 3 hours under an open atmosphere, were applied according to the DTA/TG results. Powder X-ray diffraction XRD analyses were performed to determine the phase properties of the phosphor systems after the sintering process. It was proved that the structures of two of the phosphor systems were well formed in except that the Zn2SiO4 had some ZnO secondary phases. The expected photoluminescence (PL) results were presented and the transitions of the Eu3+ ions were observed for both phosphors.

Synthesis and Characterization of BNKT/ZnO Ferroelectric Lead-Free Nanocomposites

2014 ◽  
Vol 979 ◽  
pp. 232-235 ◽  
Author(s):  
C. Wichasilp ◽  
S. Introng ◽  
W. Maithong ◽  
N. Kruea-In ◽  
C. Kruea-In
Keyword(s):  
Room Temperature ◽  
Crystallization Behavior ◽  
Ferroelectric Properties ◽  
Measurement Data ◽  
Dielectric Measurement ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray

In this research, the effects of ZnO nanoparticles additive on crystallization behavior, dielectric and ferroelectric properties of Bi0.5(Na0.81,K0.19)0.5TiO3 ceramics were investigated. The samples were synthesized by solid state reaction technique, where powders were calcined at 850 °C for 4 h and ceramics were sintered at 1100-1150 °C for 4 h. Phase formation was determined by X-ray diffraction technique (XRD). The X-ray diffraction analysis of the ceramics suggests that all samples exhibited a perovskite structure. The dielectric properties under room temperature and various temperatures were also determined. Dielectric measurement data showed that the additive influenced dielectric constant and dielectric loss. Furthermore, the hysteresis loop behaviors slightly changed with increasing the nanoparticles contents.

The Reaction of Cp*ReH6, Cp* = C5Me5, with Monoborane to Yield a Novel Rhenaborane. Synthesis and Characterization of arachno-Cp*ReH3B3H8

2002 ◽  
Vol 67 (6) ◽  
pp. 808-812 ◽  
Author(s):  
Sundargopal Ghosh ◽  
Alicia M. Beatty ◽  
Thomas P. Fehlner
Keyword(s):  
Solid State ◽  
Single Crystal ◽  
Diffraction Study ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray

The rhenaborane Cp*ReH3B3H8, which is generated by the reaction of Cp*ReH6 with BH3·THF, has been characterized spectroscopically in solution and by a single-crystal X-ray diffraction study in the solid state as a hydrogen-rich arachno-metallatetraborane.

Synthesis and Characterization of Rare Earth (Sm,Y) Light Conversion Film

2009 ◽  
Vol 610-613 ◽  
pp. 257-261
Author(s):  
Ya Ru Ni ◽  
Lian Chao Wu ◽  
Chun Hua Lu ◽  
Zhong Zi Xu
Keyword(s):  
Rare Earth ◽  
Fluorescence Spectroscopy ◽  
Polyvinyl Alcohol ◽  
Infrared Spectra ◽  
Ultra Violet ◽  
Dimethyl Sulphoxide ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray

In this article, Sm(Sal)xPhen, SmyY1-y(Sal)3Phen were synthesized and its films were prepared. They were characterized by infrared spectra (IR), ultra-violet visible spectrometer (UV), X-ray diffraction (XRD) and fluorescence spectroscopy. Sm/Y complexes and its mixture doped with the polyvinyl alcohol (PVA) showed photoluminescence at the wavelength of 646 nm. There was an excellent compatibility among Sm/Y complexes, the polyvinyl alcohol (PVA) and dimethyl sulphoxide (DMSO), which were used to prepare the resin film. The results indicated that Sm/Y rare earth light conversion films were better light conversion films with good compatibility in resins, and with emission wavelength suitable for plants’ photosynthesis.

scholarly journals A Luminescent 1D Silver Polymer Containing [2.2]Paracyclophane Ligands

2021 ◽  
Vol 9 ◽  
Author(s):  
Campbell F. R. Mackenzie ◽  
Lucie Delforce ◽  
D. Rota Martir ◽  
David B. Cordes ◽  
Alexandra M. Z. Slawin ◽  
...  
Keyword(s):  
Solid State ◽  
Coordination Polymer ◽  
Building Blocks ◽  
Synthesis And Characterization ◽  
Crystalline Solid ◽  
X Ray Diffraction ◽  
Blue Fluorescence ◽  
X Ray ◽  
1D Coordination Polymer

[2.2]Paracyclophane scaffolds have seen limited use as building blocks in supramolecular chemistry. Here, we report the synthesis and characterization of a 1D coordination polymer consisting of silver(I) ions bound to a [2.2]paracyclophane scaffold functionalized with two 4-pyridyl units. The structure of the polymer has been determined from single crystal X-ray diffraction analysis and reveals two different silver coordination motifs that alternate along the 1D coordination polymer. The coordination polymer exhibits strong blue and sky-blue fluorescence in solution and in the crystalline solid state, respectively.

Synthesis and Characterization of Mixed Rare Earths Hydroxide Catalyst

2018 ◽  
Vol 936 ◽  
pp. 53-57
Author(s):  
Bheechanat Duangdee ◽  
Dussadee Rattanaphra ◽  
Anusith Thanapimmetha ◽  
Maythee Saisriyoot ◽  
Penjit Srinophakun
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Rare Earth ◽  
Rare Earths ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Precipitation ◽  
Scanning Electron

This work presents the synthesis and characterization of mixed rare earths hydroxide heterogeneous catalyst. The catalysts were prepared by co-precipitation of mixed rare earths with NaOH at different pH (6, 7 and 12). The prepared catalysts were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD) and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM–EDS). The XRF results showed that the catalyst composed of cerium (Ce), neodymium (Nd), lanthanum (La), praseodymium (Pr) and samarium (Sm) being predominant at pH up to 7. Particularly, cerium (Ce) was favorable precipitation at pH 7. This results were confirm by SEM-EDS. The Ce (OH)3 phase was clearly observed for the mixed rare earth catalyst precipitated at pH 7. The XRF, SEM-EDS and XRD results were consistency.

Sign in / Sign up

Export Citation Format

Share Document