scholarly journals Reflection of waves from a mobile elastic layer in a multimode waveguide

2021 ◽  
Vol 24 (2) ◽  
pp. 73-78
Author(s):  
Elena S. Ustinova ◽  
Vladimir I. Volovach ◽  
Tatyana A. Antipova ◽  
Kaira A. Adishirin-Zade

Waveguide structures are used to transmit energy and information signals in a wide range of wavelengths and, in terms of wave-guiding physical properties, usually have mutual (identical) properties in forward and backward directions. The asymmetry of the structure and external influences can often cause non-reciprocity of structures for waves, propagating in mutually opposite directions (this property, although limited, is already used in the so-called nonreciprocal devices of microwave, EHF and optical ranges such as ferrite valves, circulators, phase shifters). At the same time, the nonreciprocal properties of wave-guiding structures, independent of their physical nature, were not considered. It is found, that the motion of the medium filling the acoustic waveguide leads to nonreciprocity of its parameters in the forward and backward directions. The degree of nonreciprocity is proportional to the velocity of the medium. The velocity of the medium also affects the propagation velocity of acoustic waves and leads to a change in the critical frequencies or critical wavelengths of the waveguide modes. As the velocity of the medium increases, the number of modes for which the propagation condition is satisfied increases as well.

Alloy Digest ◽  
1982 ◽  
Vol 31 (8) ◽  

Abstract ANACONDA Alloy 268 is a copper-zinc alloy with excellent cold-working properties; it can be cold worked by all the conventional fabrication processes. Its corrosion resistance is excellent-to-good in most environments. This alloy has a wide range of applications including items such as springs, bathroom fixtures, automotive radiators, lamp sockets and sanitary traps. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-442. Producer or source: Anaconda American Brass Company.


Alloy Digest ◽  
1981 ◽  
Vol 30 (8) ◽  

Abstract CENTRI-CAST GRAY IRON 50 is a centrifugally cast gray iron with a nominal tensile strength of 50,000 psi. It is cast in the form of tubing which has a wide range of uses in applications where size and shape are of paramount importance and freedom from pattern cost is an important consideration. Among its many applications are farm machinery, seals, bushings, machine tools and general machinery uses. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on casting, heat treating, machining, and surface treatment. Filing Code: CI-51. Producer or source: Federal Bronze Products Inc..


Alloy Digest ◽  
1979 ◽  
Vol 28 (9) ◽  

Abstract CENTRI-CAST GRAY IRON 55 is a centrifugally cast gray iron with a nominal tensile strength of 55,000 psi. It is produced in the form of tubing which has a wide range of uses in applications where size and shape are of paramount importance and freedom from pattern cost is an important consideration. Typical applications are seals, bushings, farm machinery, casings and general machinery uses. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on casting, heat treating, machining, and surface treatment. Filing Code: CI-48. Producer or source: Federal Bronze Products Inc..


Alloy Digest ◽  
1977 ◽  
Vol 26 (10) ◽  

Abstract CHASE 14310 is a high-conductivity copper with excellent resistance to thermal softening. It is a deoxidized, electronic grade of copper with excellent formability, weldability and plateability. It is available in strip form and has a wide range of applications. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, joining, and surface treatment. Filing Code: Cu-341. Producer or source: Chase Brass & Copper Company Inc..


Alloy Digest ◽  
1987 ◽  
Vol 36 (5) ◽  

Abstract SAE 1345 is a through-hardening, manganese alloy steel with intermediate hardenability. It is most commonly used where good strength is needed but low-to-medium toughness is sufficient. Its wide range of uses in tools and machinery includes hand tools, gears, shafts, bolts and housings. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SA-425. Producer or source: Alloy steel mills and foundries.


Alloy Digest ◽  
1981 ◽  
Vol 30 (7) ◽  

Abstract SAE 8642 is a triple-alloy steel that can be hardened by austenitizing and quenching in oil. This steel has moderate hardenability with relative high strength and toughness, especially in the quenched-and-tempered condition. It is used in a wide range of components, parts and tools; examples are bolts, shafts, gears, wrenches, axles and housings. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SA-382. Producer or source: Alloy steel mills and foundries.


Alloy Digest ◽  
2009 ◽  
Vol 58 (3) ◽  

Abstract Domex 550MC is a hot-rolled, high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-12.80 mm. The alloy meets or exceeds the requirements of S550MC in EN 10149-2. Applications include a wide range of fabricated components and steel structures, including truck chassis, crane booms, and earthmoving machines. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fatigue. It also includes information on forming, heat treating, and joining. Filing Code: SA-594. Producer or source: SSAB Swedish Steel Inc.


Alloy Digest ◽  
1985 ◽  
Vol 34 (3) ◽  

Abstract UNS NO. G50461 is a low-chromium alloy steel with boron added to increase its hardenability. This steel has medium hardenability and strength with good ductility. It is used in a wide range of machinery and tool applications where its properties meet the requirements. Another grade (UNS No. H50461) has similar properties but slightly wider ranges in percentages of carbon, manganese and chromium; this is known as the H-grade (Hardenability grade). This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SA-408. Producer or source: Alloy steel mills and foundries.


1998 ◽  
Vol 05 (02) ◽  
pp. 493-499 ◽  
Author(s):  
V. S. Gurin

Surface modification by means of STM has became a well-known method for the artificial formation of nanometer and atomic scale structures. The physical nature of surface modification can consist in a wide range of phenomena (from mechanical indentation up to specific tip-induced chemistry). The high electrical field at the STM tip is considered to be the main feature of STM modification experiments. The field strength is comparable with intramolecular ones and can influence the chemical bonding in surface structures. The model of STM-stimulated modification is considered using the quantum-chemical ab initio approach for a surface cluster in the high electrical field. The destabilization effect, energy level shift, and bond polarization under the STM tip field occur and can show the atomistic nature of surface transformations in STM.


Sign in / Sign up

Export Citation Format

Share Document