scholarly journals The impact of parameter modifications in the Diesel engine power system on the emissions of harmful compounds

2020 ◽  
Vol 180 (1) ◽  
pp. 36-40
Author(s):  
Jerzy MERKISZ ◽  
Maciej BAJERLEIN ◽  
Bartłomiej ZIELIŃSKI
Keyword(s):  
Diesel Engine ◽  
Diesel Oil ◽  
Operating Conditions ◽  
Urban Traffic ◽  
Emission Measurement ◽  
Portable Emission Measurement System ◽  
Vehicle Operation ◽  
Torque Values ◽  
Exhaust Gas Emissions ◽  
The Impact

The article presents the results of emission tests and vehicle operation indicators fueled with diesel oil. The tests were carried out for a passenger vehicle equipped with a diesel engine meeting Euro 3 emissions standard, moving in urban traffic. The measurements were carried out using modern PEMS (Portable Emission Measurement System) enabling the emission of gaseous components from exhaust systems of the tested object. On the basis of the conducted tests, the load characteristics were determined using the torque values obtained along with the engine speeds. The measurement route included two cycles: urban driving and fast acceleration. The aim of the study was to assess the impact of modifications to the control maps on CO, CO2, PM and NOx exhaust gas emissions under real operating conditions.

On-Road Gaseous Emission Characteristics of China IV CNG Bus in Shanghai

2013 ◽  
Vol 690-693 ◽  
pp. 1864-1871 ◽  
Author(s):  
Di Ming Lou ◽  
Si Li Qian ◽  
Zhi Yuan Hu ◽  
Pi Qiang Tan
Keyword(s):  
Emission Factor ◽  
High Speed ◽  
Idle Time ◽  
Operating Conditions ◽  
Vehicle Emission ◽  
Emission Characteristics ◽  
Emission Measurement ◽  
Gaseous Emissions ◽  
Average Speed ◽  
Portable Emission Measurement System

In this paper, on-road CO, THC, NOX, CO2 gaseous emissions characteristics of china IV CNG bus were analyzed based on on-road vehicle emission test in the peak and non-peak hours of city traffic in Shanghai using a portable emission measurement system (PEMS). The experimental results reveal that: compared with the condition results in the non-peak hours, it (conditions in the peak hours) have lower average speed, longer idle time and shorter high speed time; the NOX emission factor and rate in the peak hour reduced by 5.66% and 70.2%; the CO, HC, CO2 emissions factors are increased by 47.2%, 32.6%, 20.8%, and the CO, HC, CO2 emissions rates reduced by 1.94%, 26.5%, 48.7% respectively, compared with that in the non-peak hours; The CO, HC, NOX, CO2 emissions factors all decreased as bus speed increased, while they increased as bus acceleration increased; the gaseous emissions rates all increased as bus speed increased; both the emissions factors and emissions rates contributions are highest at accelerations, higher at cruise speeds, and the lowest at decelerations for non-idling buses; the emissions rates under the condition of idling is lowest; gaseous emissions contribution under the various operating conditions has displayed certain correlations with the percentage of the time for different operating conditions.

The Impact of Electric Hybrid Compressor to Make Transport Environmentally Friendly

2013 ◽  
Vol 391 ◽  
pp. 207-212
Author(s):  
Maciej Bajerlein
Keyword(s):  
Energy Consumption ◽  
Operating Conditions ◽  
Vehicle Speed ◽  
Suspension Systems ◽  
Actual Operating ◽  
Vehicle Operation ◽  
Total Energy Balance ◽  
The Impact ◽  
Road Emission ◽  
Speed Engine

This paper presents the investigations, whose aim was to determine the influence of the operation of electric and mechanical compressors on the energy consumption of city buses in public transport. The tests were performed on pneumatic systems used in city transit vehicles whose underlying component is a compressor generating pressure for the brake and suspension systems. Owing to the application of a portable analyzer - SEMTECH DS the emissions (with a secondly resolution) of CO, HC, NOx, CO2 in the exhaust gases were measured. The on-road emission tests were performed in the actual operating conditions in SORT driving tests. These tests reflect the actual vehicle operation in a real task through preset procedures of their realization and measurements determining the energy consumption and exhaust emissions or the influence of the vehicle accessories and all variables (vehicle speed, engine load, acceleration or distance covered) on the total energy balance. The on-road tests were performed on a runway of the Bednary airstrip in Poland.

Bio Diesel Oil of Mustard

2013 ◽  
Vol 5 (1) ◽  
pp. 37-49
Author(s):  
Liu Hongcong
Keyword(s):  
Renewable Energy ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Irrigation System ◽  
Standard Procedure ◽  
Diesel Oil ◽  
Operating Conditions ◽  
Mustard Oil ◽  
Mustard Seed ◽  
Complex Deformation

This paper represents the mustard oil is a kind of renewable energy and alternative fuel of the future. In order to cope with the current situation of load shedding, and reduce dependence on imported fuels, the Bangladesh government to encourage the use of renewable energy. Because the diesel engine with multiple functions, including small pumping irrigation system and backup generators, diesel fuel is much higher than that of any other gasoline fuel. In Bangladesh, mustard oil used as edible oil has been all over the country. Mustard is a widely grown plants, more than demand in Bangladesh and the mustard seed is produced annually. Therefore, to use the remaining mustard oil diesel fuel as a substitute. Fuel properties determine the standard procedure in fuel testing laboratory. An experimental device, and then a small diesel engine made in a laboratory using different conversion from the properties of biodiesel blend of mustard oil. The study found, biodiesel diesel fuel has a slightly different than the property. Also observed, and bio diesel, engine is able to without difficulty, but deviates from its optimal performance. Biodiesel was different (B20, B30, B50) of the blends have been used in engine or a fuel supply system, in order to avoid the complex deformation. Finally, it has been carried out to compare the performance of different operating conditions with different blends of Biodiesel Engine, in order to determine the optimal blends.

Thermodynamic Analysis of Ethanol-Diesel Oil and Waste Heat Recovery for Diesel Engines

2014 ◽  
Vol 1070-1072 ◽  
pp. 140-145
Author(s):  
Ming Yue He ◽  
Hong Tao Gao ◽  
Wang Liu
Keyword(s):  
Diesel Engine ◽  
Thermodynamic Analysis ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Cooling Water ◽  
Engine Performance ◽  
Alternative Fuel ◽  
Diesel Oil ◽  
The Impact

In this paper, for the purpose of providing a scientific reference for saving energy and improving the efficiency of diesel engine, the impact of ethanol diesel-oil alternative fuel and waste heat recovery are investigated on the basis of thermodynamic analysis. The results illustrate that, after using ethanol diesel alternative fuel, engine performance parameters are of no big change, however, the exhaust emissions are significantly reduced; Recycling the energy contained in the exhaust gas and cooling water, can achieve the purpose of energy conservation and emissions reduction, beside improving the thermal efficiency and exergy efficiency of the diesel engine.

Effects of dual biofuel approach for total elimination of diesel on injection system by reciprocatory friction monitor

2017 ◽  
Vol 232 (9) ◽  
pp. 1068-1076 ◽  
Author(s):  
Paramvir Singh ◽  
Varun Goel ◽  
SR Chauhan
Keyword(s):  
Diesel Engine ◽  
Fossil Fuels ◽  
Operating Conditions ◽  
Injection System ◽  
Effect Of Temperature ◽  
Compression Ignition ◽  
Oil Blends ◽  
Compression Ignition Engines ◽  
The Impact ◽  
Total Elimination

Biodiesel is a promising fuel which shows potential and gradually received attention as a best alternate feedstock for diesel engine. Previous investigations have shown that use of double biofuels in a diesel engine can be a promising aspect for complete elimination of diesel from compression ignition engines which will decrease our dependency on fossil fuels. The tribological performance of injection system is primarily based on the lubricity characteristics of the fuel. So, it is imperative to a more diversified research about the impact of using double biofuels in engine. In the present investigation, different biodiesel-oil blends were investigated using the ASTM D6079 by the reciprocatory friction monitor. The effect of temperature variation on lubricity characteristics was also studied. The biodiesel-oil blends shows improvement in results as compared to diesel. Biodiesel is prone to oxidation due to availability of unsaturation in their moieties. The effects of oxidation on lubricity characteristics were also studied. It was also found that the operating conditions collectively affected the lubricity characteristics of tested feedstocks.

scholarly journals A control method of fuel distribution by combustion chamber zones and its dependence on injection conditions

2018 ◽  
Vol 22 (Suppl. 5) ◽  
pp. 1425-1434 ◽  
Author(s):  
Mikhail Shatrov ◽  
Valery Malchuk ◽  
Andrey Dunin ◽  
Ivan Shishlov ◽  
Vladimir Sinyavski
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Effective Cross Section ◽  
Injection Rate ◽  
Operating Conditions ◽  
Common Rail ◽  
Fuel System ◽  
Excessive Pressure ◽  
The Common ◽  
The Impact

A method of fuel injection rate shaping of the Diesel engine common rail fuel system with common rail injectors and solenoid control is proposed. The method envisages the impact on control current of impulses applied to the control solenoid valve of the common rail injectors for variation of the injection rate shape. At that, the fuel is supplied via two groups of injection holes. The entering edges of the first group with the coefficient of flow, ??B, were located in the sack volume and the entering edges of the second group (coefficient of flow, ??H) - on the locking taper surface of the nozzle body. The coefficients of flow, ??B, and ??H differ considerably and depend on the valve needle position. This enables to adjust the injection quantity by injection holes taking into account operating conditions of the Diesel engine and hence - by the combustion chamber zones. Using the constant fuel flow set-up, characteristic of the effective cross-section of the common rail fuel system injector holes was investigated. The diameter of injector holes was 0.12 ? 0.135 mm. The excessive pressure at the entering edges varied from 30 to 150 MPa and more and the excessive pressure in the volume behind the output edge - from 0 to 16 MPa.

Investigation and Optimization of Diesel Engine Outputs under Undi Biodiesel-Diesel Strategies

2021 ◽  
pp. 1-23
Author(s):  
Pravin Ashok Madane ◽  
Subrata Bhowmik ◽  
Rajsekhar Panua ◽  
P. Sandeep Varma ◽  
Abhishek Paul
Keyword(s):  
Carbon Monoxide ◽  
Particulate Matter ◽  
Diesel Engine ◽  
Thermal Efficiency ◽  
Operating Conditions ◽  
Oxides Of Nitrogen ◽  
Brake Thermal Efficiency ◽  
Trade Off ◽  
Unburned Hydrocarbon ◽  
The Impact

Abstract The present investigation accentuates the impact of Undi biodiesel blended Diesel on combustion, performance, and exhaust fume profiles of a single-cylinder, four-stroke Diesel engine. Five Undi biodiesel-Diesel blends were prepared and tested at four variable loads over a constant speed of 1500 (±10) rpm. The Undi biodiesel incorporation to Diesel notably improves the in-cylinder pressure and heat release rate of the engine. The higher amount of Undi biodiesel addition enhances the brake thermal efficiency and brake specific energy consumption of the engine. In addition, the Undi biodiesel facilitates to reduce the major pollutants, such as brake specific unburned hydrocarbon, brake specific carbon monoxide, and brake specific particulate matter emissions with slightly higher brake specific oxides of nitrogen emissions of the engine. To this end, a trade-off study was introduced to locate the favorable Diesel engine operating conditions under Undi biodiesel-Diesel strategies. The optimal Diesel engine outputs were found to be 32.65% of brake thermal efficiency, 1.21 g/kWh of brake specific cumulated oxides of nitrogen and unburned hydrocarbon, 0.94 g/kWh of brake specific carbon monoxide, and 0.32 g/kWh of brake specific particulate matter for 50% (by volume) Undi biodiesel share blend at 5.6 bar brake mean effective pressure with a relative closeness value of 0.978, which brings up the pertinence of the trade-off study in Diesel engine platforms.

CFD Combustion and Emission Formation Modeling for a HSDI Diesel Engine Using Detailed Chemistry

2006 ◽  
Author(s):  
Valeri I. Golovitchev ◽  
Luca Montorsi ◽  
Carlo Alberto Rinaldini ◽  
Angelo Rosetti
Keyword(s):  
Diesel Engine ◽  
Chemical Kinetics ◽  
Diesel Engines ◽  
Equivalence Ratio ◽  
Diesel Oil ◽  
Operating Conditions ◽  
Fuel Vapor ◽  
Formation Mechanisms ◽  
Engine Operation ◽  
3D Engine

In order to comply with current emissions regulations, a detailed analysis of the combustion and emission formation processes in the Diesel engines accounting for the effect of the main operating parameters is required. The present study is based both on 0D and 3D numerical simulations by compiling 0D chemical kinetics calculations for Diesel oil surrogate combustion and emission (soot, NOx) formation mechanisms to construct a φ-T (equivalence ratio - temperature) parametric map. In this map, the regions of emissions formation are depicted defining a possible optimal path between the regions by placing on the same map the engine operation conditions represented by the computational cells, whose parameters (equivalence ratio and temperature) are calculated by means of 3D engine modelling. Unlike previous approaches based on static parametric φ-T maps to analyze different combustion regimes and emission formations in Diesel engines, the present paper focuses on a construction of dynamic φ-T maps, in which the pressures and the elapsed times were taken in compliance with those calculated in the 3D engine simulations. The 0D chemical kinetics calculations have been performed by the SENKIN code of the Chemkin-2 library. In-cylinder conditions represented by computational cells with known φ and T are predicted using KIVA-3V code. When cells are plotted on the map, they identify the trajectories helping to navigate between the emissions regions by varying hardware and injection parameters. Sub-models of the KIVA-3V, rel. 2 code has been modified including spray atomization, droplet collision and evaporation, accounting for multi-component fuel vapor coupled with the improved versions of the chemistry/turbulence interaction model and new formulation of the combustion kinetics for the diesel oil surrogate (consisting in 70 species participating in 310 reactions). Simulations were performed for the HSDI 1.300 Fiat Diesel engine at optimized engine operating conditions and pilot injections. Finally, numerical results are compared with the experimental data on in-cylinder pressure, Rate of Heat Release, RoHR, and selected species distributions.

Sign in / Sign up

Export Citation Format

Share Document