scholarly journals Eco-friendly Water-based Nanolubricants for Industrial-scale Hot Steel Rolling

2020 ◽  
Author(s):  
Hui Wu ◽  
Hamidreza Kamali ◽  
Mingshuai Huo ◽  
Fei Lin ◽  
Shuiquan Huang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Oxide Scale ◽  
Rolling Force ◽  
Pure Water ◽  
Surface Hardness ◽  
Industrial Scale ◽  
Steel Rolling ◽  
Scale Thickness ◽  
Lubrication Performance ◽  
Water Based

Eco-friendly and low-cost water-based nanolubricants containing rutile TiO2 nanoparticles (NPs) were developed for accelerating their applications in industrial-scale hot steel rolling. The lubrication performance of developed nanolubricants was evaluated in a 2-high Hille 100 experimental rolling mill at a rolling temperature of 850 ℃ in comparison to that of pure water. The results indicate that the use of nanolubricant enables to decrease the rolling force, reduce the surface roughness and the oxide scale thickness, and enhance the surface hardness. In particular, the nanolubricant consisting of 4 wt% TiO2, 10 wt% glycerol, 0.2 wt% sodium dodecyl benzene sulfonate (SDBS) and 1 wt% Snailcool exhibits the best lubrication performance by lowering the rolling force, surface roughness and oxide scale thickness up to 8.1%, 53.7% and 50%, respectively. The surface hardness is increased by 4.4%. The corresponding lubrication mechanisms are attributed to its superior wettability and thermal conductivity associated with the synergistic effect of rolling, mending and laminae forming that are contributed by TiO2 NPs.

scholarly journals Eco-Friendly Water-Based Nanolubricants for Industrial-Scale Hot Steel Rolling

Lubricants ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 96
Author(s):  
Hui Wu ◽  
Hamidreza Kamali ◽  
Mingshuai Huo ◽  
Fei Lin ◽  
Shuiquan Huang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Oxide Scale ◽  
Rolling Force ◽  
Pure Water ◽  
Surface Hardness ◽  
Industrial Scale ◽  
Steel Rolling ◽  
Scale Thickness ◽  
Lubrication Performance ◽  
Water Based

Eco-friendly and low-cost water-based nanolubricants containing rutile TiO2 nanoparticles (NPs) were developed for accelerating their applications in industrial-scale hot steel rolling. The lubrication performance of developed nanolubricants was evaluated in a 2-high Hille 100 experimental rolling mill at a rolling temperature of 850 °C in comparison to that of pure water. The results indicate that the use of nanolubricant enables one to decrease the rolling force, reduce the surface roughness and the oxide scale thickness, and enhance the surface hardness. In particular, the nanolubricant consisting of 4 wt % TiO2, 10 wt % glycerol, 0.2 wt % sodium dodecyl benzene sulfonate (SDBS) and 1 wt % Snailcool exhibits the best lubrication performance by lowering the rolling force, surface roughness and oxide scale thickness by up to 8.1%, 53.7% and 50%, respectively. The surface hardness is increased by 4.4%. The corresponding lubrication mechanisms are attributed to its superior wettability and thermal conductivity associated with the synergistic effect of rolling, mending and laminae forming that are contributed by TiO2 NPs.

scholarly journals Performance Evaluation and Lubrication Mechanism of Water-Based Nanolubricants Containing Nano-TiO2 in Hot Steel Rolling

2018 ◽  
Author(s):  
Hui Wu ◽  
Jingwei Zhao ◽  
Liang Luo ◽  
Shuiquan Huang ◽  
Lianzhou Wang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Oxide Scale ◽  
Rolling Force ◽  
Nano Tio2 ◽  
Steel Rolling ◽  
Scale Thickness ◽  
Lubricating Film ◽  
Lubrication Performance ◽  
Water Based ◽  
Lubrication Conditions

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO2 from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO2 concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO2 demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO2.

scholarly journals The influence of soak temperature and forging lubricant on surface properties of steel forgings

2020 ◽  
Author(s):  
S. Hill ◽  
R. P. Turner ◽  
P. Wardle
Keyword(s):  
Surface Roughness ◽  
Surface Hardness ◽  
Lower Surface ◽  
Design Parameters ◽  
Compression Tests ◽  
Molybdenum Disulphide ◽  
Small Series ◽  
Ring Compression ◽  
Water Based ◽  
The Impact

AbstractA small series of ring compression tests were performed on BS970:708M40 alloy steel. The samples were tested using a 2-factor temperature variable, and a 4-factor lubricant variable, as the design parameters. Two differing soak temperatures were used, namely 1030 °C and 1300 °C respectively. The lubricants applied at the billet to tooling interface were synthetic water–based, graphite water–based, graphite and molybdenum disulphide viscous grease, and finally, unlubricated samples were tested. The ring compression tests were performed using a traditional drop forging hammer and induction heating to minimise any unintentional process variability. The impact that the two varying process parameters have upon the compression sample was then assessed by measuring each sample’s surface hardness and surface roughness prior to and post forging with fully calibrated equipment. It was demonstrated that the higher soak temperature of 1300 °C yielded a lower surface hardness value and higher surface roughness than the lower soak temperature, 1030 °C. The two water-based lubricants offered negligible change in results compared with the unlubricated forging, strongly suggesting that the lubricants were evaporated off the surface prior to forging. However, the results from the graphite–molybdenum disulphate grease do indicate in particular higher surface roughness than other lubricants, and a non-symmetric distortion pattern.

scholarly journals Study on Oxidation of Stainless Steels During Hot Rolling

2012 ◽  
pp. 240-250
Author(s):  
Z. Y. Jiang ◽  
D. B. Wei ◽  
K. Tieu ◽  
J. X. Huang ◽  
A. W. Zhang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Oxide Scale ◽  
Stainless Steels ◽  
Hot Rolling ◽  
Steel Substrate ◽  
Substrate Surface ◽  
304 Stainless Steel ◽  
304L Stainless Steel ◽  
Scale Thickness

The oxidation of stainless steels 304 and 304L during hot rolling is studied in this paper. Results show the oxide scale thickness decreases significantly with an increase of reduction, and the oxide scales of both 304 and 304L stainless steels were found more deformable than the steel substrate. Surface roughness shows a complicated transfer during the hot rolling process due to the complexity of oxide scale characteristics. Also, surface roughness decreases with an increase of reduction. The friction coefficient increases with reduction in all cases, and the increase is more significant in the case of the 304 stainless steel than that of 304L stainless steel.

scholarly journals Effects of Roughness on Stresses in an Oxide Scale Formed on a Superalloy Substrate

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 479
Author(s):  
Yang Zhao ◽  
Fan Sun ◽  
Peng Jiang ◽  
Yongle Sun
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Residual Stresses ◽  
Oxide Scale ◽  
Rough Surface ◽  
Alumina Scale ◽  
Growth Stress ◽  
Oxide Growth ◽  
Substrate Thickness ◽  
Roughness Effect

The effects of surface roughness on the stresses in an alumina scale formed on a Fecralloy substrate are investigated. Spherical indenters were used to create indents with different radii and depths to represent surface roughness and then the roughness effect was studied comprehensively. It was found that the residual stresses in the alumina scale formed around the rough surface are almost constant and they are dominated by the curvature rather than the depth of the roughness. Oxidation changes the surface roughness. The edge of the indent was sharpened after oxidation and the residual stress there was released presumably due to cracking. The residual stresses in the alumina scale decrease with increase in oxidation time, while the substrate thickness has little effect, given that the substrate is thicker than the alumina scale. Furthermore, the effect of roughness on the oxide growth stress is analysed. This work indicates that the surface roughness should be considered for evaluation of stresses in coatings.

scholarly journals Effect of Water-Based Nanolubricants in Ultrasonic Vibration Assisted Grinding

2018 ◽  
Vol 2 (4) ◽  
pp. 80 ◽  
Author(s):  
Mir Molaie ◽  
Ali Zahedi ◽  
Javad Akbari
Keyword(s):  
Surface Roughness ◽  
Specific Energy ◽  
Material Removal ◽  
Normal Force ◽  
Tangential Force ◽  
Process Efficiency ◽  
Multiwall Carbon Nanotube ◽  
Ultrasonic Vibrations ◽  
Mql Grinding ◽  
Water Based

Currently, because of stricter environmental standards and highly competitive markets, machining operations, as the main part of the manufacturing cycle, need to be rigorously optimized. In order to simultaneously maximize the production quality and minimize the environmental issues related to the grinding process, this research study evaluates the performance of minimum quantity lubrication (MQL) grinding using water-based nanofluids in the presence of horizontal ultrasonic vibrations (UV). In spite of the positive impacts of MQL using nanofluids and UV which are extensively reported in the literature, there is only a handful of studies on concurrent utilization of these two techniques. To this end, for this paper, five kinds of water-based nanofluids including multiwall carbon nanotube (MWCNT), graphite, Al2O3, graphene oxide (GO) nanoparticles, and hybrid Al2O3/graphite were employed as MQL coolants, and the workpiece was oscillated along the feed direction with 21.9 kHz frequency and 10 µm amplitude. Machining forces, specific energy, and surface quality were measured for determining the process efficiency. As specified by experimental results, the variation in the material removal nature made by ultrasonic vibrations resulted in a drastic reduction of the grinding normal force and surface roughness. In addition, the type of nanoparticles dispersed in water had a strong effect on the grinding tangential force. Hybrid Al2O3/graphite nanofluid through two different kinds of lubrication mechanisms—third body and slider layers—generated better lubrication than the other coolants, thereby having the lowest grinding forces and specific energy (40.13 J/mm3). It was also found that chemically exfoliating the graphene layers via oxidation and then purification prior to dispersion in water promoted their effectiveness. In conclusion, UV assisted MQL grinding increases operation efficiency by facilitating the material removal and reducing the use of coolants, frictional losses, and energy consumption in the grinding zone. Improvements up to 52%, 47%, and 61%, respectively, can be achieved in grinding normal force, specific energy, and surface roughness compared with conventional dry grinding.

scholarly journals Performance Evaluation and Lubrication Mechanism of Water-Based Nanolubricants Containing Nano-TiO2 in Hot Steel Rolling

Lubricants ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 57 ◽  
Author(s):  
Hui Wu ◽  
Jingwei Zhao ◽  
Liang Luo ◽  
Shuiquan Huang ◽  
Lianzhou Wang ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Lubrication Mechanism ◽  
Nano Tio2 ◽  
Steel Rolling ◽  
Water Based

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

Sign in / Sign up

Export Citation Format

Share Document