scholarly journals Design and Development of Vertical Axis Wind Turbine

Author(s):  
Samir Deshmukh ◽  
Sagar Charthal

Wind energy is the kinetic energy associated with movement of large masses of air. These motions result from uneven heating of atmosphere by sun creating temperature, density, pressure differences. It is an indirect form of solar energy The device used to convert kinetic energy of wind into electrical power is called a wind turbine. Vertical Axis wind power generators, represent a very promising future for wind power generation. In present study an attempt is made to utilize at low velocity wind below 4m/s for useful power generation using magnetic levitation for vertical axis wind turbine (VAWT) termed as Maglev turbine. A single large Maglev turbine can give output more than conventional horizontal axis wind turbine (HAWT). The rotor that is designed to harness enough air to rotate the shaft at low and high wind speeds while keeping the centre of mass closer to the base of yielding stability due to Maglev effect. The efficiency of turbine is increased by replacing the conventional bearings by magnets in repulsion; the magnetic levitation helps the turbine to spin at much faster rate as it eliminates the stresses on the shaft of turbine. The major components are placed at the ground level which ensures the safety of turbine.

2019 ◽  
Vol 2019.25 (0) ◽  
pp. 18E16
Author(s):  
Hiroshi OKUBO ◽  
Ryo HATAKEYAMA ◽  
Hidemi ONODERA ◽  
Tsuyoshi SATO ◽  
Hironori FUJII ◽  
...  

2019 ◽  
pp. 68-76

Modelo Teórico de los Sistemas de Aerogeneración Eléctrica para las Turbinas Eólicas de Eje Vertical Theoretical Model of Electric Aerogeneration Systems for Vertical Axis Wind Turbines Anthony Pinedo, Guillermo Ramírez, Lincoln Chiguala, Juan Estrada, David Asmat, Renny Nazario, Daniel Delfín, Lourdes Noriega, Silvia Aguilar, Randy Rosas, Luisa Juárez DOI: https://doi.org/10.33017/RevECIPeru2009.0027/ RESUMEN Existen dos tipos de sistemas de aerogeneración eléctrica por turbinas eólicas, los llamados de eje horizontal (HAWT) y los de eje vertical (VAWT). Ambos proponen ventajas y desventajas, dependiendo de muchos factores. Pero en general, no fue hasta hace unos años que el segundo tipo había sido ignorado, debido a la poca potencia que producía en comparación con los HAWT. Pero con la adaptación de un sistema de levitación, y un nuevo sistema de inducción magnética, las VAWT, lograron incrementar notablemente la energía obtenida, llegando incluso a superar a los HAWT. A pesar que los modelos VAWT han sido harto estudiados en cuanto al esquema experimental y de diseño, no se formuló ninguna explicación sólida, partiendo de principios básicos, sobre el funcionamiento de los VAWT. En este trabajo, se propone un modelo teórico del funcionamiento de los mismos. Para ello, se realizan tres estudios: la interacción del viento con las aspas del aerogenerador, el sistema de levitación magnética y la producción de energía eléctrica por inducción magnética. Estos tres fenómenos, permiten definir y predecir el funcionamiento de tal sistema de aerogeneración. Además, permite «visualizar» la influencia de los diferentes parámetros sobre la eficiencia del sistema, y así pues, poder manejar, los parámetros que controlamos experimentalmente, para obtener una eficiencia óptima. Palabras clave: aerogeneración eléctrica, turbinas de aire, eje vertical, levitación magnética. ABSTRACT There are two types of systems of electric aerogeneration by using wind turbines, one is called horizontal axis wind turbine (HAWT) and the other one is called vertical axis wind turbine (VAWT). Both of them have advantages and disadvantages depending on many factors. Since the second one had produced lees power than the first one, they were ignored. However, the adaptation of a levitation system and a new system of magnetic induction made VAWT increase the power produced and exceed the HAWT. Although VAWT models were studied enough in the design and experimental scheme, there is no solid explanation, based on basic principles, on the operation of the VAWT. In this paper is proposed a theoretical model of VAWT operation. Therefore, three studies are done: the interaction between wind and blades of the turbine, the magnetic levitation system and the energy production by magnetic induction. Those studies make us able to know and predict the operation of those systems. Since, we shall know how many factors are affecting the efficiency of the system; we shall be able to control those parameters in order to get the best efficiency. Keywords: electric aerogeneration, vertical axis wind turbine, magnetic levitation.


2013 ◽  
Vol 37 (3) ◽  
pp. 305-319 ◽  
Author(s):  
Mario R. Chiarelli ◽  
Andrea Massai ◽  
Giovanni Russo ◽  
Davide Atzeni ◽  
Francesco Bianco

2012 ◽  
Vol 34 (3) ◽  
pp. 169-184 ◽  
Author(s):  
Hoang Thi Bich Ngoc

Vertical axis wind turbine technology has been applied last years, very long after horizontal axis wind turbine technology. Aerodynamic problems of vertical axis wind machines are discussible. An important problem is the determination of the incidence law in the interaction between wind and rotor blades. The focus of the work is to establish equations of the incidence depending on the blade azimuth, and to solve them. From these results, aerodynamic torques and power can be calculated. The incidence angle is a parameter of velocity triangle, and both the factors depend not only on the blade azimuth but also on the ratio of rotational speed and horizontal speed. The built computational program allows theoretically selecting the relationship of geometric parameters of wind turbine in accordance with requirements on power, wind speed and installation conditions.


Author(s):  
Sadek Ameziane ◽  
Abdesselem Chikhi ◽  
Mohammed Salah Aggouner

Background: The presented article is a contribution to the realization of a wind emulator based on a continuous-current machine. The development of this topic focuses on the modeling of a vertical axis wind turbine, a DC motor with independent excitation and its control via a chopper. Methods: To carry out this work, we have studied and designed the electronic and mechanical sensors as well as a command implemented on the dSPACE DS1103 system. Results: The main purpose of this work is related, on one hand, to the control of the motor turbine by imposing the wind profile and on the other hand generate the command of the implanted MPPT. The experimental results obtained showed the great performances which characterize this improved wind energy system. Conclusion: Finally, a wind turbine with variable speed is a system having a complex model; however, a detailed model of the interaction between the wind and the aero-turbine is useful to understand certain phenomena such as rotational sampling or the spatial filter.


KnE Energy ◽  
2015 ◽  
Vol 2 (2) ◽  
pp. 172
Author(s):  
Tedy Harsanto ◽  
Haryo Dwi Prananto ◽  
Esmar Budi ◽  
Hadi Nasbey

<p>A vertical axis wind turbine triple-stage savonius type has been created by using simple materials to generate electricity for the alternative wind power plant. The objective of this research is to design a simple wind turbine which can operate with low wind speed. The turbine was designed by making three savonius rotors and then varied the structure of angle on the three rotors, 0˚, 90˚ and 120˚. The dimension of the three rotors are created equal with each rotor diameter 35 cm and each rotor height 19 cm. The turbine was tested by using blower as the wind sources. Through the measurements obtained the comparisons of output power, rotation of turbine, and the level of efficiency generated by the three variations. The result showed that the turbine with angle of 120˚ operate most optimally because it is able to produce the highest output power and highest rotation of turbine which is 0.346 Watt and 222.7 RPM. </p><p><strong>Keywords</strong>: Output power; savonius turbine; triple-stage; the structure of angle</p>


Author(s):  
Sourabh Deshpande ◽  
Nithin Rao ◽  
Nitin Pradhan ◽  
John L. Irwin

Utilizing the advantages of additive manufacturing methods, redesigning, building and testing of an existing integral Savonius / Darrieus “Lenz2 Wing” style vertical axis wind turbine is predicted to improve power generation efficiency. The current wind turbine blades and supports made from aluminum plate and sheet are limiting the power generation due to the overall weight. The new design is predicted to increase power generation when compared to the current design due to the lightweight spiral Darrieus shaped hollow blade made possible by 3D printing, along with an internal Savonius blade made from aluminum sheet and traditional manufacturing techniques. The design constraints include 3D printing the turbine blades in a 0.4 × 0.4 × 0.3 m work envelope while using a Stratasys Fortus 400mc and thus the wind turbine blades are split into multiple parts with dovetail joint features, when bonded together result in a 1.2 m tall working prototype. Appropriate allowance in the mating dovetail joints are considered to facilitate the fit and bonding, as well as angle, size and placement of the dovetail to maximize strength. The spiral shape and Darrieus style cross section of the blade that provides the required lift enabling it to rotate from the static condition are oriented laterally for 3D printing to maximize strength. The bonding of the dovetail joints is carried out effectively using an acetone solution dip. The auxiliary components of the wind turbine which include the center support pole, top and bottom support, and center Savonius blades are manufactured using lightweight aluminum. Design features are included in the 3D printed blade parts so that they can be assembled with the aluminum parts in bolted connections. Analysis of the 3D CAD models show that the hybrid aluminum and hollow 3D printed blade construction provides a 50% cost savings over a 3D printed fully solid blade design while minimizing weight and maximizing the strength where necessary. Analysis of the redesign includes a detailed weight comparison, structural strength and the cost of production. Results include linear static finite element analysis for the strength in dovetail joint bonding and the aluminum to 3D printed connections. Additional data reported are the time frame for the design and manufacturing of the system, budget, and an operational analysis of the wind turbine with concern for safety. Results are analyzed to determine the advantages in utilizing a hybrid additive manufacturing and aluminum construction for producing a more efficient vertical axis wind turbine. Techniques used in the production of this type of wind turbine blade are planned to be utilized in similar applications such as a lightweight hovercraft propeller blade design to be tested in future research projects.


Author(s):  
Jinwook Kim ◽  
Dohyung Lee ◽  
Junhee Han ◽  
Sangwoo Kim

The Vertical Axis Wind Turbine (VAWT) has advantages over Horizontal Axis Wind Turbine (HAWT) that it allows less chance to be degraded independent of wind direction and turbine can be operated even at the low wind speed. The objective of this study is to analyze aerodynamics of the VAWT airfoil and investigate the ideal shape of airfoil, more specifically cambers. The analysis of aerodynamic characteristics with various cambers has been performed using numerical simulation with CFD software. As the numerical simulation discloses local physical features around wind turbine, aerodynamic performance such as lift, drag and torque are computed for single airfoil rotation and multiple airfoil rotation cases. Through this study more effective airfoil shape is suggested based vortex-airfoil interaction studies.


Sign in / Sign up

Export Citation Format

Share Document