Remote Activated Completion Technology Enhances Operational Efficiency of Offshore Wells in Middle East

2021 ◽  
Author(s):  
Vijay Kumar Keerthivasan ◽  
Dustin Young ◽  
Cathrine Mehus ◽  
Bjornar Gjedrem ◽  
Moetaz Abdelghany ◽  
...  
Keyword(s):  
Middle East ◽  
Research And Development ◽  
Field Trial ◽  
New Technology ◽  
Operational Efficiency ◽  
Qualification Test ◽  
Test Program ◽  
Qualification Testing ◽  
Operational Issues ◽  
Reducing Potential

Abstract To access a larger amount of pay zone, well trajectories are becoming longer and more complex, creating greater challenges for running completion liners. A liner shoe is a casing accessory tool that aids in the running of completion liners in long wells by allowing auto-filling of the liner and enabling pumping through the bottom of the liner. Upon reaching planned liner depth, the liner shoe is closed to allow for pressure testing and subsequent completion operations. Conventional methods used to close a liner shoe involve well intervention to set plugs or by dropping a ball, and there are inherent costs and risks associated with these operations. This paper presents the development and deployment of a remotely activated electronic liner shoe (ELS) for offshore applications that enables interventionless closing of the liner shoe, thereby improving operational efficiency, and reducing potential operational issues that could occur while closing the liner shoe conventionally. The ELS allows the operator to precisely control when the liner shoe closes – either based on pre-programmed pressure signals, a timer, or a combination of the two. A major operator in the Middle East required an ELS to be developed and qualified specifically for their offshore well conditions. A new technology qualification program was devised in collaboration with the operator to qualify both the electronic and mechanical functionalities of the tool. This paper documents the methods and results of the extensive qualification test program. The development and qualification process were successfully completed within 10 months at research and development facilities in Norway. Following qualification testing, the ELS was first deployed for the operator in an offshore well in Q4 of 2019. Operational considerations in programming the remote functionality of the tool is presented in this paper. After a successful field trial, the ELS has been run in more than 15 offshore wells and has become the standard option in the operator's completion program.

scholarly journals The beginning of spreading of technology of manufacturing of Geometric Microlites with dorsal flat retouch

2014 ◽  
Vol 3 (3) ◽  
pp. 136-143
Author(s):  
Valery Aleksandrovich Manko
Keyword(s):  
Middle East ◽  
Eastern Europe ◽  
Eastern Mediterranean ◽  
New Technology

The author analyzes the emergence and spread of geometric microliths with flat pressing dorsal retouch in the Near and Middle East, in the basin of the Eastern Mediterranean and in Eastern Europe. We consider the typology of these products and their role in the Neolithic complexes of Eastern Europe. Author makes analysis of the typology and technology of geometrics and detected primary and secondary centers of dissemination of new technology.

2001 Manufacturing Odyssey: Impact of Globalization on Technology Requirements

2001 ◽  
Author(s):  
Shounak Athavale ◽  
Matt Davies ◽  
Miro Suga ◽  
James Williams ◽  
Kesh Narayan ◽  
...  
Keyword(s):  
Research And Development ◽  
New Technology ◽  
Panel Discussion ◽  
Business Environment ◽  
Manufacturing Technology ◽  
Government Agencies ◽  
Global Business ◽  
Seamless Integration ◽  
Effective Manner ◽  
Manufacturing Technologies

Abstract A report of the ASME Global Technologies Committee in 1999 stressed the need to inform government agencies about the importance of the activities of mechanical engineers. In particular, while government agencies and the public in general seem to understand the romantic idea of concept generation (inventors and scientists), they do not comprehend the efforts that go into realization of an idea into a usable product (engineering and manufacturing) and the benefits of this activity to the global society. In fact the product realization process makes the cutting edge products affordable and available to every strata of the society. In spite of current success, engineering and manufacturing functions are continuously challenged by the changing demands and business environment. Specifically, opening of world markets and industrial globalization require that manufacturing functions are not only flawless and efficient, but also be compatible with the global business environment. The goal of this panel is to showcase past contributions to the field of manufacturing and build a case for continued support of future manufacturing research and education. The panelist will begin the discussion by addressing five topics/questions. Comments and question from the audience are encouraged. The five topics/questions of focus for this panel discussion are 1. Innovative products of last century like cars, planes, computers, etc. remain accessible to masses only due to the revolutionary manufacturing technology at the time. Which of the past manufacturing technologies will you attribute this tremendous success to? Are any of these technologies obsolete or are on the verge of extinction? 2. During past few years most of the world has opened up to international trade and business. Global marketplace is not just a dream; it is a reality and is here to stay. Besides, the business drivers and associated economic advantages, supporting engineering and manufacturing technologies have played a vital role in keeping the global business afloat. In your opinion what key technology drivers (including any manufacturing technologies) are behind this success? Do any of the technical issues need immediate attention? 3. During the 20th century we have witnessed tremendous growth in manufacturing technology. Traditional research and development focused on getting the product out i.e. development of manufacturing and assembly processes and their optimization. The next big thing was to get the product out in an efficient and cost-effective manner. It fueled research in material flow and inventory management, resulting in techniques like JIT, Kanban, supply-chain management, etc. More recently eManufacturing initiatives (B2B, B2C, B2E, etc.) have made a tremendous impact in seamless integration of business operations (suppliers-purchasing-engineering-manufacturing-marketing-service), resulting in productivity gains. What’s next? 4. As resources are geographically distributed and scarce; consolidation, collaboration and leveraging often become key issues in a global industry. Research and Development may not be any different. In your opinion, are the days for “lone researchers/developers” over? If yes, how do you envision future R&D activities to function? If no, how to incorporate individual R&D efforts? 5. Commercial success of technical breakthroughs depends on the workforce that can implement the new technology and consumers who can utilize it. Often the term “technology overload” is used when either of these groups fails to comprehend the new technology. To avoid this trap, it is necessary for future manufacturing leaders and innovators to have a unique skill set. What kind of educational training and experience will be required of future manufacturing engineers/researchers?

1000 Hour Qualification Test of the Textron Lycoming TF40B Marine Gas Turbine Engine for the U.S. Navy LCAC Craft

1988 ◽  
Author(s):  
Michael J. Zoccoli
Keyword(s):  
Gas Turbine ◽  
High Power ◽  
Duty Cycle ◽  
Development Program ◽  
Continuous Operation ◽  
Qualification Test ◽  
Turbine Engine ◽  
Qualification Testing ◽  
Carbon Erosion ◽  
The U.S

This paper describes the qualification testing of the TF40B marine gas turbine in accordance with the duty cycle as specified in MIL-E-17341C, but with modifications that reflect the specific engine application to the U.S. Navy LCAC vehicle. Among the particular requirements of the 1000 hour test are continuous operation in a salt-laden environment of given concentration and humidity, and frequent shutdowns from relatively high power with an ensuing soakback interval. The narrative discusses the method of test, the duty cycle, and the results which were obtained. In an epilogue which focuses on posttest activities, a description is given of the corrective actions taken to resolve certain problems that arose during the course of the test. One such problem, namely the occurrence of carbon erosion upon certain hot section components, was eliminated by modification to the combustor, in a very successful posttest test development program.

scholarly journals Internet Marketing Adoption by Iranian Distribution Industry

2018 ◽  
Vol 9 (2) ◽  
pp. 33-61
Author(s):  
Sepideh Zahiri ◽  
Hatem El-Gohary ◽  
Javed Hussain
Keyword(s):  
Developing Countries ◽  
Middle East ◽  
Technology Adoption ◽  
Empirical Research ◽  
New Technology ◽  
Internet Marketing ◽  
Developed Countries ◽  
Marketing Strategies ◽  
The Internet ◽  
New Technology Adoption

This article describes how although the internet has become a significant platform for the advancement of marketing strategies and developments, there have been inadequate empirical research efforts concerning its adoption for conducting internet marketing in developing countries, specifically in the Middle East area, and more particularly in Iran. Previous studies investigated internet marketing adoption and acceptance extensively, by employing different theories of new technology adoption in developed countries, while there have been inadequate empirical research efforts concerning its adoption in developing countries. It is widely recognised that the adoption of internet marketing can offer substantial opportunities for Small and Medium Sized Enterprises (SMEs). In developing countries, internet marketing opportunities can be a meaningful approach for SMEs to be able to compete with large businesses and to access, with lowest possible costs, targeted customers.

scholarly journals Cutting the Face

2018 ◽  
Vol 2 (1) ◽  
pp. 49-71
Author(s):  
Geoffrey Fitzgibbon Hughes
Keyword(s):  
Social Media ◽  
Middle East ◽  
New Media ◽  
Social Control ◽  
New Technologies ◽  
New Technology ◽  
State Building ◽  
Power Structures ◽  
Existing Structures ◽  
The Face

The local uptake of new media in the Middle East is shaped by deep histories of imperialism, state building, resistance and accommodation. In contemporary Jordan, social media is simultaneously encouraging identification with tribes and undermining their gerontocratic power structures. Senior men stress their own importance as guarantors (‘faces’), who restore order following conflicts, promising to pay their rivals a large surety if their kin break the truce. Yet, ‘cutting the face’ (breaking truces) remains an alternative, one often facilitated by new technologies that allow people to challenge pre-existing structures of communication and authority. However, the experiences of journalists and other social media mavens suggest that the liberatory promise of the new technology may not be enough to prevent its reintegration into older patterns of social control.

scholarly journals Status of Catalytic Combustion R&D for the Department of Energy Advanced Turbine Systems Program

1999 ◽  
Author(s):  
D. B. Fant ◽  
G. S. Jackson ◽  
H. Karim ◽  
D. M. Newburry ◽  
P. Dutta ◽  
...  
Keyword(s):  
Research And Development ◽  
Catalytic Combustion ◽  
High Efficiency ◽  
Department Of Energy ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Development Status ◽  
Catalyst Durability ◽  
Operational Issues ◽  
The U.S

This paper discusses some of the advanced concepts and research and development associated with implementing catalytic combustion to achieve ultra-low-NOx emissions in the next generation of land-based gas turbine engines. In particular, the paper presents current development status and design challenges being addressed by Siemens Westinghouse Power Corp. for large industrial engines (> 200 MW) and by Solar Turbines for smaller engines (< 20 MW) as part of the U.S. Department of Energy’s (DOE) Advanced Turbine Systems (ATS) program. Operational issues in implementing catalytic combustion and the current needs for research in catalyst durability and operability are also discussed. This paper indicates how recent advances in reactor design and catalytic coatings have made catalytic combustion a viable technology for advanced turbine engines and how further research and development may improve catalytic combustion systems to better meet the durability and operability challenges presented by the high-efficiency, ultra-low emissions ATS program goals.

Modal Survey Testing and Vibration Qualification Testing: The Integrated Approach

2003 ◽  
Vol 46 (1) ◽  
pp. 110-118 ◽  
Author(s):  
Bart Peeters ◽  
Herman Van der Auweraer ◽  
Patrick Guillaume
Keyword(s):  
Mathematical Models ◽  
Structural Integrity ◽  
Integrated Approach ◽  
Analytical Models ◽  
Qualification Test ◽  
Load Prediction ◽  
Qualification Testing ◽  
Satellite Equipment

In the assessment of the structural integrity and launch-environment survivability of satellite structures, dynamic mathematical models are used for load prediction. These analytical models are test-verified by a modal survey test. Once the vibration environment is specified, the satellite equipment is subjected to shaker excitation in order to reproduce this environment. This paper investigates the possibilities to integrate both the modal survey and the vibration qualification test.

TOPAZ II Non-Nuclear Qualification Test Program

1994 ◽  
Author(s):  
Glen L. Schmidt ◽  
Boris Ogloblin ◽  
Valeri Sinkevich ◽  
Frank Thome ◽  
Mohamed S. El-Genk ◽  
...  
Keyword(s):  
Qualification Test ◽  
Test Program
Sign in / Sign up

Export Citation Format

Share Document