Planning of Pilot Injection of Surfactant-Polymer Composition to Improve Oil Recovery from Carbonate Reservoir of Kharyaga Oilfield and Evaluation of the Results

2021 ◽  
Author(s):  
Yuri Mikhailovich Trushin ◽  
Anton Sergeevich Aleshchenko ◽  
Oleg Nikolaevich Zoshchenko ◽  
Mark Suleimanovich Arsamakov ◽  
Ivan Vasilevich Tkachev ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Hydrodynamic Model ◽  
Surfactant Concentration ◽  
Pilot Project ◽  
Tracer Test ◽  
Carbonate Reservoir ◽  
Field Conditions ◽  
Polymer Composition ◽  
Displacement Efficiency ◽  
Water Displacement

Abstract The paper considers the use of a surfactant-polymer composition for the mobilization of light paraffinic oil from the D3-III carbonate reservoir at a reservoir temperature of 62°C, as well as the results of its tests in field conditions. Earlier, the composition showed its effectiveness on model carbonate cores with salinity from current (50-80 g/l) to reservoir (up to 170 g/l), in the presence of surfactants, type III microemulsions according to Winsor with oil were obtained. Based on the results of the filtration experiments performed on our own core from the productive formation D3-III, an increase in the displacement efficiency of surfactant-polymer compositions compared to water was obtained 11–14% (with a total surfactant concentration of 1%), irreversible surfactant losses in water-saturated rock–up to 0, 38 mg/g. Displacement efficiency after water and surfactant-polymer composition flooding was also estimated in the field conditions using SWCTT; its results were interpreted by various methods (analytical, in a hydrodynamic simulator), and also compared with laboratory results. Within a single-well tracer test, an assessment of the residual saturation after water filtration and injection of a surfactant-polymer composition was carried out under the following conditions: the target research radius is 3.5 m; porosity 10%, effective reservoir thickness 38 m. Based on the results of SWCTT, an increase in the displacement efficiency of 16.7% was obtained in comparison with water displacement (total surfactant concentration 1%) using an analytical method of interpretation. The adaptation of the SWCTT results on the hydrodynamic model was carried out, the most influencing parameters on the quality of adaptation were determined. The selection and justification of a pilot area for a multi-well pilot project was carried out, a sector hydrodynamic model of the site was built, and calculations were made to assess additional oil production.

Simulation of Miscible Displacement in Full-Diameter Carbonate Cores

1982 ◽  
Vol 22 (05) ◽  
pp. 647-657 ◽  
Author(s):  
J.P. Batycky ◽  
B.B. Maini ◽  
D.B. Fisher
Keyword(s):  
Oil Recovery ◽  
Water Saturation ◽  
Accurate Determination ◽  
Miscible Displacement ◽  
Carbonate Reservoir ◽  
Core Material ◽  
Immiscible Fluid ◽  
Displacement Efficiency ◽  
Carbonate Cores ◽  
Capacitance Model

Abstract Miscible gas displacement data obtained from full-diameter carbonate reservoir cores have been fitted to a modified miscible flow dispersion-capacitance model. Starting with earlier approaches, we have synthesized an algorithm that provides rapid and accurate determination of the three parameters included in the model: the dispersion coefficient, the flowing fraction of displaceable volume, and the rate constant for mass transfer between flowing and stagnant volumes. Quality of fit is verified with a finite-difference simulation. The dependencies of the three parameters have been evaluated as functions of the displacement velocity and of the water saturation within four carbonate cores composed of various amounts of matrix, vug, and fracture porosity. Numerical simulation of a composite core made by stacking three of the individual cores has been compared with the experimental data. For comparison, an analysis of Berea sandstone gas displacement also has been provided. Although the sandstone displays a minor dependence of gas recovery on water saturation, we found that the carbonate cores are strongly affected by water content. Such behavior would not be measurable if small carbonate samples that can reflect only matrix properties were used. This study therefore represents a significant assessment of the dispersion-capacitance model for carbonate cores and its ability to reflect changes in pore interconnectivity that accompany water saturation alteration. Introduction Miscible displacement processes are used widely in various aspects of oil recovery. A solvent slug injected into a reservoir can be used to displace miscibly either oil or gas. The necessary slug size is determined by the rate at which deterioration can occur as the slug is Another commonly used miscible process involves addition of a small slug within the injected fluids or gases to determine the nature and extent of inter well communication. The quantity of tracer material used is dictated by analytical detection capabilities and by an understanding of the miscible displacement properties of the reservoir. We can develop such understanding by performing one-dimensional (1D) step-change miscible displacement experiments within the laboratory with selected reservoir core material. The effluent profiles derived from the experiments then are fitted to a suitable mathematical model to express the behavior of each rock type through the use of a relatively small number of parameters. This paper illustrates the efficient application of the three-parameter, dispersion-capacitance model. Its application previously has been limited to use with small homogeneous plugs normally composed of intergranular and intencrystalline porosity, and its suitability for use with cores displaying macroscopic heterogeneity has been questioned. Consequently, in addition to illustrating its use with a homogeneous sandstone, we fit data derived from previously reported full-diameter carbonate cores. As noted earlier, these cores were heterogeneous, and each of them displayed different dual or multiple types of porosity characteristic of vugular and fractured carbonate rocks. Dispersion-Capacitance Model The displacement efficiency of one fluid by a second immiscible fluid within a porous medium depends on the complexity of rock and fluid properties. SPEJ P. 647^

Pilot Project Evaluating WAG Efficiency for Carbonate Reservoir in Eastern Siberia

2021 ◽  
Author(s):  
Valentina Zharko ◽  
Dmitriy Burdakov
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Oil Production ◽  
Pilot Project ◽  
Carbonate Reservoir ◽  
Recovery Factor ◽  
Eastern Siberia ◽  
Water Cut ◽  
Wag Injection ◽  
Injection Rates

Abstract The paper presents the results of a pilot project implementing WAG injection at the oilfield with carbonate reservoir, characterized by low efficiency of traditional waterflooding. The objective of the pilot project was to evaluate the efficiency of this enhanced oil recovery method for conditions of the specific oil field. For the initial introduction of WAG, an area of the reservoir with minimal potential risks has been identified. During the test injections of water and gas, production parameters were monitored, including the oil production rates of the reacting wells and the water and gas injection rates of injection wells, the change in the density and composition of the produced fluids. With first positive results, the pilot area of the reservoir was expanded. In accordance with the responses of the producing wells to the injection of displacing agents, the injection rates were adjusted, and the production intensified, with the aim of maximizing the effect of WAG. The results obtained in practice were reproduced in the simulation model sector in order to obtain a project curve characterizing an increase in oil recovery due to water-alternating gas injection. Practical results obtained during pilot testing of the technology show that the injection of gas and water alternately can reduce the water cut of the reacting wells and increase overall oil production, providing more efficient displacement compared to traditional waterflooding. The use of WAG after the waterflooding provides an increase in oil recovery and a decrease in residual oil saturation. The water cut of the produced liquid decreased from 98% to 80%, an increase in oil production rate of 100 tons/day was obtained. The increase in the oil recovery factor is estimated at approximately 7.5% at gas injection of 1.5 hydrocarbon pore volumes. Based on the received results, the displacement characteristic was constructed. Methods for monitoring the effectiveness of WAG have been determined, and studies are planned to be carried out when designing a full-scale WAG project at the field. This project is the first pilot project in Russia implementing WAG injection in a field with a carbonate reservoir. During the pilot project, the technical feasibility of implementing this EOR method was confirmed, as well as its efficiency in terms of increasing the oil recovery factor for the conditions of the carbonate reservoir of Eastern Siberia, characterized by high water cut and low values of oil displacement coefficients during waterflooding.

Alkyl Ether Carboxylate Surfactants for Chemically Enhanced Oil Recovery in Harsh Field Conditions

2015 ◽  
Author(s):  
G. Alvarez Jürgenson ◽  
C. Bittner ◽  
V. Kurkal-Siebert ◽  
G. Oetter ◽  
J. Tinsley
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Field Conditions ◽  
Alkyl Ether

Saturated carbon dioxide nanofluids enhanced oil recovery in carbonate reservoir cores using nuclear magnetic resonance

2021 ◽  
Author(s):  
Yongsheng Tan ◽  
Qi Li ◽  
Liang Xu ◽  
Xiaoyan Zhang ◽  
Tao Yu
Keyword(s):  
Carbon Dioxide ◽  
Nuclear Magnetic Resonance ◽  
Magnetic Resonance ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Carbonate Reservoir ◽  
Carbonate Reservoirs ◽  
Residual Oil ◽  
Core Flooding ◽  
Nuclear Magnetic

<p>The wettability, fingering effect and strong heterogeneity of carbonate reservoirs lead to low oil recovery. However, carbon dioxide (CO<sub>2</sub>) displacement is an effective method to improve oil recovery for carbonate reservoirs. Saturated CO<sub>2</sub> nanofluids combines the advantages of CO<sub>2</sub> and nanofluids, which can change the reservoir wettability and improve the sweep area to achieve the purpose of enhanced oil recovery (EOR), so it is a promising technique in petroleum industry. In this study, comparative experiments of CO<sub>2</sub> flooding and saturated CO<sub>2</sub> nanofluids flooding were carried out in carbonate reservoir cores. The nuclear magnetic resonance (NMR) instrument was used to clarify oil distribution during core flooding processes. For the CO<sub>2</sub> displacement experiment, the results show that viscous fingering and channeling are obvious during CO<sub>2</sub> flooding, the oil is mainly produced from the big pores, and the residual oil is trapped in the small pores. For the saturated CO<sub>2</sub> nanofluids displacement experiment, the results show that saturated CO<sub>2</sub> nanofluids inhibit CO<sub>2</sub> channeling and fingering, the oil is produced from the big pores and small pores, the residual oil is still trapped in the small pores, but the NMR signal intensity of the residual oil is significantly reduced. The final oil recovery of saturated CO<sub>2</sub> nanofluids displacement is higher than that of CO<sub>2</sub> displacement. This study provides a significant reference for EOR in carbonate reservoirs. Meanwhile, it promotes the application of nanofluids in energy exploitation and CO<sub>2</sub> utilization.</p>

The Combined Flooding of Dispersed Particle Gel and Surfactant for Conformance Control and EOR: From Experiment to Pilot Test

2021 ◽  
Author(s):  
Xia Yin ◽  
Tianyi Zhao ◽  
Jie Yi
Keyword(s):  
Oil Recovery ◽  
Formation Energy ◽  
High Salinity ◽  
Surfactant Solution ◽  
Pilot Test ◽  
Control Performance ◽  
Core Flooding ◽  
Displacement Efficiency ◽  
Conformance Control ◽  
And Performance

Abstract The water channeling and excess water production led to the decreasing formation energy in the oilfield. Therefore, the combined flooding with dispersed particle gel (DPG) and surfactant was conducted for conformance control and enhanced oil recovery in a high temperature (100-110°C) high salinity (>2.1×105mg/L) channel reservoir of block X in Tahe oilfield. This paper reports the experimental results and pilot test for the combined flooding in a well group of Block X. In the experiment part, the interfacial tension, emulsifying capacity of the surfactant and the particle size during aging of DPG were measured, then, the conformance control and enhanced oil recovery performance of the combined flooding was evaluated by core flooding experiment. In the pilot test, the geological backgrounds and developing history of the block was introduced. Then, an integrated study of EOR and conformance control performance in the block X are analyzed by real-time monitoring and performance after treatment. In addition, the well selection criteria and flooding optimization were clarified. In this combined flooding, DPG is applied as in-depth conformance control agent to increase the sweep efficiency, and surfactant solution slug following is used for improve the displacement efficiency. The long term stability of DPG for 15 days ensures the efficiency of in-depth conformance control and its size can increase from its original 0.543μm to 35.5μm after aging for 7 days in the 2.17×105mg/L reservoir water and at 110°C. In the optimization, it is found that 0.35% NAC-1+ 0.25% NAC-2 surfactant solution with interfacial tension 3.2×10-2mN/m can form a relatively stable emulsion easily with the dehydrated crude oil. In the double core flooding, the conformance control performance is confirmed by the diversion of fluid after combined flooding and EOR increases by 21.3%. After exploitation of Block X for 14 years, the fast decreasing formation energy due to lack of large bottom water and water fingering resulted in a decreasing production rate and increasing watercut. After combined flooding in Y well group with 1 injector and 3 producers, the average dynamic liquid level, daily production, and tracing agent breakthrough time increased, while the watercut and infectivity index decreased. The distribution rate of injected fluid and real-time monitoring also assured the conformance control performance. The oil production of this well group was increased by over 3000 tons. Upon this throughout study of combined flooding from experiment to case study, adjusting the heterogeneity by DPG combined with increasing displacement efficiency of surfactant enhanced the oil recovery synergistically in this high salinity high temperature reservoir. The criteria for the selection and performance of combined flooding also provides practical experiences and principles for combined flooding.

Research and Application of Multi-Slug and Equi-Fluidity Oil Displacement Mechanism

2015 ◽  
Vol 733 ◽  
pp. 43-46
Author(s):  
Jiang Min Zhao ◽  
Tian Ge Li
Keyword(s):  
Pressure Gradient ◽  
Flow Rate ◽  
Oil Recovery ◽  
Recovery Rate ◽  
Actual Situation ◽  
Displacement Efficiency ◽  
Displacement Method ◽  
Oil Displacement ◽  
Oil Displacement Efficiency ◽  
Swept Volume

In this paper, several aspects of the improvement of the oil recovery were analyzed theoretically based on the mechanism that equi-fluidity enhances the pressure gradient. These aspects include the increase of the flow rate and the recovery rate, of the swept volume, and of the oil displacement efficiency. Also, based on the actual situation, the author designed the oil displacement method with gathered energy equi-fluidity, realizing the expectation of enhancing oil recovery with multi-slug and equi-fluidity oil displacement method.

Sign in / Sign up

Export Citation Format

Share Document