scholarly journals Investigation on the Cutting Mechanism of Al/SiCp Composites in Ultrasonic Elliptical Vibration Machining

2021 ◽  
Author(s):  
Wenxiang Chen ◽  
Xu Zhang
Keyword(s):  
Stress Distribution ◽  
Cutting Force ◽  
Surface Integrity ◽  
Machining Process ◽  
Von Mises Stress ◽  
Cutting Mechanism ◽  
Machined Surface ◽  
Elliptical Vibration ◽  
Von Mises ◽  
Ultrasonic Elliptical Vibration

Abstract Aluminum (Al)-based silicon carbide (SiC) material composites are considered as difficult-to-machine materials because of the presence of hard reinforced SiC particles, which results in a greater cutting force and poor surface integrity during the machining process. This paper uses two finite element models to study the difference in the machining mechanism between ultrasonic elliptical vibration cutting (UEVC) and ordinary cutting (OC). Moreover, this paper mainly focuses on the influence of UEVC on cutting force, von Mises stress distribution, surface integrity, and chip formation. The models are validated by comparing chip shapes and machined surface features in OC machining Al/SiCp experience from the literature. Simulation results indicate that the cutting mechanism of Al/SiCp on UEVC is different from that of OC and has several good properties. At the same cutting parameters, high frequency vibration makes the cutting force of UEVC exhibit variable periodicity and reduces average cutting force. The instantaneous impact of tool and fast separation results in a more concentrated von Mises stress distribution, thereby resulting in the particles having a greater break degree than that obtained with OC. A comparison of the surface roughness values from the simulation result shows that UEVC obtains better surface integrity than OC does.

scholarly journals Numerical Analysis in Ultrasonic Elliptical Vibration Cutting (UEVC) Combined With Electrical Discharge Cutting (EDC) For Ti6Al4V

2021 ◽  
Author(s):  
Rendi Kurniawan ◽  
Moran Xu ◽  
Chang Ping Li ◽  
Gun Chul Park ◽  
Ye In Kwak ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Cutting Force ◽  
Cutting Forces ◽  
Electrical Discharge ◽  
Von Mises Stress ◽  
Elliptical Vibration Cutting ◽  
Vibration Cutting ◽  
Elliptical Vibration ◽  
Von Mises ◽  
Ultrasonic Elliptical Vibration

Abstract This paper reports the numerical analysis results of ultrasonic elliptical vibration cutting (UEVC) combined with the electrical discharge cutting (EDC), called UEVC+EDC. UEVC delivers decreasing cutting forces, repressing side-burrs, and lowering tool wear. EDC is a cutting technique using a pulsed spark to remove material using thermal energy. Difficult-to-cut materials, such as Ti-6Al-4V, can be cut effectively by combining these two techniques. A numerical study was performed using ABAQUS finite element analysis (FEA) software by investigating the von Mises stress, cutting forces, and temperature. Numerical analysis was carried out by modifying the ultrasonic vibration frequency, distance of the discharge pulse, discharge voltage, and discharge pulse radius. UEVC+EDC was compared numerically and experimentally with regular cutting (NC) and UEVC in terms of cutting force and tool temperature. The results showed that the UEVC+EDC method could improve the cutting condition by reducing the cutting force and von Mises stress and increasing the tool temperature.

Experimental Study on Prestressed Cutting of Alloy Ring Parts

2016 ◽  
Vol 836-837 ◽  
pp. 71-76
Author(s):  
Rui Tao Peng ◽  
Yang Ge Li ◽  
Xin Zi Tang ◽  
Zhuan Zhou
Keyword(s):  
Residual Stress ◽  
Titanium Alloy ◽  
Stress Distribution ◽  
Cutting Force ◽  
Surface Integrity ◽  
Compressive Residual Stress ◽  
Machining Process ◽  
Residual Tensile Stress ◽  
Machined Surface ◽  
Cutting Method

In order to solve the poor cutting performance for the titanium alloy and the serious residual tensile stress distribution on the machined surface in cutting titanium alloy, the utilization of prestressed cutting method is proposed to actively control the residual stress distribution status on the machined surface in machining process. Titanium alloy ring parts were pre-stretched at different condition by a lathe-specific pretension device respectively. By the cutting experimental, the cutting force ,chip formation and surface integrity indexes are compared and studied. The results show that in suitable compressive residual stress on machined surface are achieved by utilizing the prestressed cutting method ,meanwhile procedures of residual stress adjustment after machining could be omitted. Furthermore, the magnitude of compressive residual stress could be actively controlled by adjusting the magnitude of prestressed force in certain extent. And uniform saw-tooth chip are generated in prestressed cutting, meanwhile there’s no significant increment of cutting force. Prestressed cutting method could generate good surface integrity.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

scholarly journals The Comparative Study on Cutting Performance of Different-Structure Milling Cutters in Machining CFRP

2018 ◽  
Vol 8 (8) ◽  
pp. 1353
Author(s):  
Tao Chen ◽  
Fei Gao ◽  
Suyan Li ◽  
Xianli Liu
Keyword(s):  
Carbon Fiber ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Edge ◽  
Cutting Performance ◽  
Machining Process ◽  
Carbon Fiber Composites ◽  
Machined Surface ◽  
Milling Cutter ◽  
Machined Surface Quality

Carbon fiber reinforced plastic (CFRP) is typically hard to process, because it is easy for it to generate processing damage such as burrs, tears, delamination, and so on in the machining process. Consequently, this restricts its wide spread application. This paper conducted a comparative experiment on the cutting performance of the two different-structure milling cutters, with a helical staggered edge and a rhombic edge, in milling carbon fiber composites; analyzed the wear morphologies of the two cutting tools; and thus acquired the effect of the tool structure on the machined surface quality and cutting force. The results indicated that in the whole cutting, the rhombic milling cutter with a segmented cutting edge showed better wear resistance and a more stable machined surface quality. It was not until a large area of coating shedding occurred, along with chip clogging, that the surface quality decreased significantly. At the stage of coating wear, the helical staggered milling cutter with an alternately arranged continuous cutting edge showed better machined surface quality, but when the coating fell off, its machined surface quality began to reveal damage such as groove, tear, and fiber pullout. Meanwhile, burrs occurred at the edge and the cutting force obviously increased. By contrast, for the rhombic milling cutter, both the surface roughness and cutting force increased relatively slowly.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

Evaluation of Surface Integrity in Electrochemical Micromachining of A286 Super alloy

2021 ◽  
Author(s):  
Rajkeerthi E ◽  
Hariharan P
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Surface Integrity ◽  
Research Work ◽  
Machining Process ◽  
Electrochemical Micromachining ◽  
Dissolution Mechanism ◽  
Machined Surface ◽  
Micro Holes ◽  
Super Alloy

Abstract Surface integrity of micro components is a major concern particularly in manufacturing industries as most geometry of the products must meet out necessary surface quality requirements. Advanced machining process like electrochemical micro machining possess the capabilities to machine micro parts with best surface properties exempting them from secondary operations. In this research work, different electrolytes have been employed for producing micro holes in A286 super alloy material to achieve the best surface quality and the measurement of surface roughness and surface integrity to evaluate the machined surface is carried out. The machined micro hole provides detailed information on the geometrical features. A study of parametric analysis meant for controlling surface roughness and improvement of surface integrity has been made to find out the suitable parameters for machining. The suitability of various electrolytes with their dissolution mechanism and the influence of various electrolytes have been thoroughly studied. Among the utilized electrolytes, EG + NaNO3 electrolyte provided the best results in terms of overcut and average surface roughness.

Tool Posture Planning Method for Low Rigidity Workpiece Considering Elastic Deformation Caused by Cutting Force

2020 ◽  
Author(s):  
Jun'ichi Kaneko ◽  
Yuki Okuma ◽  
Shumpei Sugita ◽  
Takeyuki Abe
Keyword(s):  
Cutting Force ◽  
Elastic Deformation ◽  
Feed Rate ◽  
Machining Process ◽  
Machining Time ◽  
Machined Surface ◽  
Nc Program ◽  
Blade Shape ◽  
Tool Posture ◽  
The Moment

Abstract In machining process for a workpiece with low rigidity such as a blade shape, it is required to consider elastic deformation of the workpiece shape itself due to cutting force. Conventionally, reduction of the cutting force in machining process is achieved by optimization of feed rate value in NC program. On the other hand, since a decrease in the feed rate causes an increase in machining time. So, other optimization algorithm is required. In this paper, a new method to suppress the elastic deformation of the workpiece by changing tool posture in multi-axis controlled machining is proposed. The proposed method is intended for finish machining process for blade shape with a ball end mill. In the proposed method, first, the cutting force loaded on the workpiece surface in a certain posture candidate is predicted, and an instantaneous cutting force at the moment when the machining surface is generated is estimated by model-based computer simulation. Based on this results, the amount of elastic deformation on the machined surface is estimated by FEM. This process is repeated at each cutter location and tool posture candidate, and the new tool posture that can minimize machining error caused by the elastic deformation is determined at each cutter location.

Thermal-Mechanical Study of 3D Printing Technology for Rail Repair

2018 ◽  
Author(s):  
Ershad Mortazavian ◽  
Zhiyong Wang ◽  
Hualiang Teng
Keyword(s):  
Thermal Analysis ◽  
Thermal Expansion ◽  
3D Printing ◽  
Stress Distribution ◽  
Temperature Gradient ◽  
Initial Temperature ◽  
Mechanical Analysis ◽  
Von Mises Stress ◽  
Additive Materials ◽  
Von Mises

The complicated steel wheel and rail interaction on curve causes side wear on rail head. Thus, the cost of maintenance for the track on curve is significantly higher than that for track on a tangent. The objective of this research is to develop 3D printing technology for repairing the side wear. In this paper, the study examines induced residual thermal stresses on a rail during the cooling down process after 3D printing procedure using the coupled finite volume and finite element method for thermal and mechanical analysis respectively. The interface of the railhead and additive materials should conserve high stresses to prevent any crack initiation. Otherwise, the additive layer would likely shear off the rail due to crack propagation at the rail/additive interface. In the numerical analysis, a cut of 75-lb ASCE (American Society of Civil Engineers) worn rail is used as a specimen, for which a three-dimensional model is developed. The applied residual stresses, as a result of temperature gradient and thermal expansion coefficient mismatch between additive and rail materials, are investigated. At the beginning, the worn rail is at room temperature while the additive part is at a high initial temperature. Then, additive materials start to flow thermal energy into the worn rail and the ambient. The thermal distribution results from thermal analysis are then employed as thermal loads in the mechanical analysis to determine the von-Mises stress distribution as the decisive component. Then, the effect of preheating on residual stress distribution is studied. In this way, the thermo-mechanical analysis is repeated with an increase in railhead’s initial temperature. In thermal analysis, the temperature contours at different time steps for both the non-preheated and preheated cases indicate that preheating presents remarkably lower temperature gradient between rail and additive part and also represents a more gradual cooling down process to allow enough time for thermal expansion mismatch alignment. In mechanical analysis, the transversal von-Mises stress distribution at rail/additive interface is developed for all cases for comparison purposes. It is shown that preheating is a key factor to significantly reduce residual stresses by about 40% at all points along transversal direction of interface.

Sign in / Sign up

Export Citation Format

Share Document