scholarly journals Design and Simulation of GaAsN Based Solar Cell with AlGaAs Blocking Layer for Harvesting Visible To Near-Infrared Light

2021 ◽  
Author(s):  
Md Dulal Haque ◽  
Md Hasan Ali ◽  
Md Abdul Halim ◽  
A. Z. M. Touhidul Islam ◽  
Md Mahabub Hossain ◽  
...  
Keyword(s):  
Solar Cell ◽  
Near Infrared ◽  
Short Circuit ◽  
Infrared Light ◽  
Dilute Nitride ◽  
Blocking Layer ◽  
Performance Parameters ◽  
Stability Parameters ◽  
Solar Cell Performance ◽  
The Impact

Abstract In the present study, the performance parameters of GaAsN dilute nitride-based semiconductor solar cell with and without AlGaAs blocking layers have been investigated in detail by Solar Cell Capacitance Simulator in one dimensional software program (SCAPS-1D). The thickness of absorber, buffer, and blocking layers are varied to achieve the improvement of open circuit voltage, short circuit current, fill factor, efficiency and also to optimize the device structure. The impact of doping and defect densities on the solar cell performance parameters have been analyzed minutely inside the absorber, buffer, and blocking layers. The solar cell thermal stability parameters are also investigated in the temperature region from 273K to 373K. The efficiency of 43.90% and 40.05% are obtained from the proposed solar cells with and without AlGaAs blocking layer, respectively. The present findings may provide insightful approach for fabricating feasible, cost effective, and efficient dilute nitride solar cell.

scholarly journals Magnetron Sputtered Electron Blocking Layer as an Efficient Method to Improve Dye-Sensitized Solar Cell Performance

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2690
Author(s):  
Dariusz Augustowski ◽  
Paweł Kwaśnicki ◽  
Justyna Dziedzic ◽  
Jakub Rysz
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Dye Sensitized Solar Cell ◽  
Blocking Layer ◽  
Electron Blocking Layer ◽  
Solar Cell Performance ◽  
Force Microscopy ◽  
Dye Sensitized

The main efficiency loss is caused by an intensive recombination process at the interface of fluorine-doped tin oxide (FTO) and electrolyte in dye-sensitized solar cells. Electrons from the photoanode can be injected back to the redox electrolyte and, thus, can reduce the short circuit current. To avoid this, the effect of the electron blocking layer (EBL) was studied. An additional thin film of magnetron sputtered TiO2 was deposited directly onto the FTO glass. The obtained EBL was characterized by atomic force microscopy, scanning electron microscopy, optical profilometry, energy dispersive spectroscopy, Raman spectroscopy and UV-VIS-NIR spectrophotometry. The results of the current–voltage characteristics showed that both the short circuit current (Isc) and fill factor (FF) increased. Compared to traditional dye-sensitized solar cell (DSSC) architecture, the power conversion efficiency (η) increased from 4.67% to 6.07% for samples with a 7 × 7 mm2 active area and from 2.62% to 3.06% for those with an area of 7 × 80 mm2.

scholarly journals Numerical Modeling of High Conversion Efficiency FTO/ZnO/CdS/CZTS/MO Thin Film-Based Solar Cells: Using SCAPS-1D Software

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1468
Author(s):  
Samer H. Zyoud ◽  
Ahed H. Zyoud ◽  
Naser M. Ahmed ◽  
Anupama R. Prasad ◽  
Sohaib Naseem Khan ◽  
...  
Keyword(s):  
Thin Film ◽  
Numerical Modeling ◽  
Solar Cells ◽  
Solar Cell ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Short Circuit ◽  
Effect Of Temperature ◽  
Solar Cell Performance ◽  
The Impact

The numerical modeling of a copper zinc tin sulfide (CZTS)-based kesterite solar cell is described in detail in this article. To model FTO/ZnO/CdS/CZTS/MO structured solar cells, the Solar Cell Capacitance Simulator-one-dimension (SCAPS-1D) program was utilized. Numerical modeling was used to estimate and assess the parameters of various photovoltaic thin film solar cells. The impact of different parameters on solar cell performance and conversion efficiency were explored. Because the response of a solar cell is partly determined by its internal physical mechanism, J-V characteristic characteristics are insufficient to define a device’s behavior. Regardless of the conviction in solar cell modeling, variable attributes as well as many probable conditions must be handled for simulation. Promising optimized results were obtained with a conversion efficiency of (η% = 25.72%), a fill factor of (FF% = 83.75%), a short-circuit current of (JSC  = 32.96436 mA/cm2), and an open-circuit voltage of (VOC = 0.64 V). The findings will aid in determining the feasibility of manufacturing high-efficiency CZTS-based solar cells. First, in the SCAPS-1D environment, the impacts of experimentally constructed CZTS solar cells were simulated. The experimental data was then compared to the simulated results from SCAPS-1D. After optimizing cell parameters, the conversion efficiency of the improved system was observed to rise. The influence of system factors, such as the thickness, acceptor, and donor carrier concentration densities of the absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells, was explored using one-dimensional SCAPS-1D software. The suggested findings will be extremely useful to engineers and researchers in determining the best method for maximizing solar cell efficiency, as well as in the development of more efficient CZTS-based solar cells.

scholarly journals Antireflection Improvement and Junction Quality Optimization of Si/PEDOT:PSS Solar Cell with the Introduction of Dopamine@Graphene

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5986
Author(s):  
Tao Chen ◽  
Hao Guo ◽  
Leiming Yu ◽  
Tao Sun ◽  
Anran Chen ◽  
...  
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
High Performance ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrochemical Impedance Spectra ◽  
Solar Cell Performance ◽  
Photovoltaic Conversion ◽  
Photovoltaic Conversion Efficiency

Si/PEDOT: PSS solar cell is an optional photovoltaic device owing to its promising high photovoltaic conversion efficiency (PCE) and economic manufacture process. In this work, dopamine@graphene was firstly introduced between the silicon substrate and PEDOT:PSS film for Si/PEDOT: PSS solar cell. The dopamine@graphene was proved to be effective in improving the PCE, and the influence of mechanical properties of dopamine@graphene on solar cell performance was revealed. When dopamine@graphene was incorporated into the cell preparation, the antireflection ability of the cell was enhanced within the wavelength range of 300~450 and 650~1100 nm. The enhanced antireflection ability would benefit amount of the photon-generated carriers. The electrochemical impedance spectra test revealed that the introduction of dopamine@graphene could facilitate the separation of carriers and improve the junction quality. Thus, the short-circuit current density and fill factor were both promoted, which led to the improved PCE. Meanwhile, the influence of graphene concentration on device performances was also investigated. The photovoltaic conversion efficiency would be promoted from 11.06% to 13.15% when dopamine@graphene solution with concentration 1.5 mg/mL was applied. The achievements of this study showed that the dopamine@graphene composites could be an useful materials for high-performance Si/PEDOT:PSS solar cells.

scholarly journals Optimized Thin-Film Organic Solar Cell with Enhanced Efficiency

2021 ◽  
Vol 13 (23) ◽  
pp. 13087
Author(s):  
Waqas Farooq ◽  
Muhammad Ali Musarat ◽  
Javed Iqbal ◽  
Syed Asfandyar Ali Kazmi ◽  
Adnan Daud Khan ◽  
...  
Keyword(s):  
Thin Film ◽  
Solar Cell ◽  
Organic Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Bragg Reflector ◽  
Performance Parameters ◽  
Distributed Bragg Reflector

Modification of a cell’s architecture can enhance the performance parameters. This paper reports on the numerical modeling of a thin-film organic solar cell (OSC) featuring distributed Bragg reflector (DBR) pairs. The utilization of DBR pairs via the proposed method was found to be beneficial in terms of increasing the performance parameters. The extracted results showed that using DBR pairs helps capture the reflected light back into the active region by improving the photovoltaic parameters as compared to the structure without DBR pairs. Moreover, implementing three DBR pairs resulted in the best enhancement gain of 1.076% in power conversion efficiency. The measured results under a global AM of 1.5G were as follows: open circuit voltage (Voc) = 0.839 V; short circuit current density (Jsc) = 10.98 mA/cm2; fill factor (FF) = 78.39%; efficiency (η) = 11.02%. In addition, a thermal stability analysis of the proposed design was performed and we observed that high temperature resulted in a decrease in η from 11.02 to 10.70%. Our demonstrated design may provide a pathway for the practical application of OSCs.

scholarly journals Upper limit to the photovoltaic efficiency of imperfect crystals from first principles

2020 ◽  
Vol 13 (5) ◽  
pp. 1481-1491 ◽  
Author(s):  
Sunghyun Kim ◽  
José A. Márquez ◽  
Thomas Unold ◽  
Aron Walsh
Keyword(s):  
Solar Cell ◽  
Point Defects ◽  
First Principles ◽  
Cell Performance ◽  
Solar Cell Performance ◽  
Photovoltaic Efficiency ◽  
Upper Limit ◽  
The Impact

An approach is proposed to predict the impact of point defects on solar cell performance.

Cost-effective thiophene-assisted novel dopant-free hole transport materials for efficient perovskite solar cell performance

2020 ◽  
Vol 4 (9) ◽  
pp. 4754-4767 ◽  
Author(s):  
M. SasiKumar ◽  
Gurulakshmi Maddala ◽  
Meenakshamma Ambapuram ◽  
Mahesh Subburu ◽  
Jayathirtha Rao Vaidya ◽  
...  
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Cost Effective ◽  
Perovskite Solar Cell ◽  
Hole Transport ◽  
Solar Cell Performance ◽  
Free Hole ◽  
Circuit Density

Cost-effective, novel dopant-free hole transport material-assisted perovskite solar cells exhibit a champion short-circuit density 25.73 mA cm−2 and power conversion efficiency of 17.60%.

Chemical Composition Dependence of Cu2ZnSnS4 Absorbers Fabricated by Sulfurization of Thermal Evaporated Metal Precursors and Solar Cell Performance

2015 ◽  
Vol 1738 ◽  
Author(s):  
Liyuan Zhang ◽  
Sreejith Karthikeyan ◽  
Mandip J. Sibakoti ◽  
Stephen A. Campbell
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Chemical Composition ◽  
Conversion Efficiency ◽  
Small Deviation ◽  
Short Circuit ◽  
Cell Performance ◽  
Czts Thin Film ◽  
Solar Cell Performance

ABSTRACTWe investigate the synthesis of kesterite Cu2ZnSnS4 (CZTS) thin films using thermal evaporation from copper, zinc and tin pellets and post-annealing in a sulfur atmosphere. The effects of chemical composition were studied both on the absorber layer properties and on the final solar cell performance. It is confirmed that CZTS thin film chemical composition affects the carrier concentration profile, which then influences the solar cell properties. Solar cells using a CZTS thin film with composition ratio Cu/(Zn+Sn) = 0.87, and Zn/Sn = 1.24 exhibited an open-circuit voltage of 483 mV, a short-circuit current of 14.54 mA/cm2, a fill factor of 37.66 % and a conversion efficiency of 2.64 %. Only a small deviation from the optimal chemical composition can drop device performance to a lower level, which confirms that the CZTS solar cells with high conversion efficiency existed in a relatively narrow composition region.

Sign in / Sign up

Export Citation Format

Share Document