Root Growth and Diffusion Rates as Functions of Oxygen Concentration

1961 ◽  
Vol 25 (6) ◽  
pp. 463-467 ◽  
Author(s):  
L. H. Stolzy ◽  
J. Letey ◽  
T. E. Szuszkiewicz ◽  
O. R. Lunt
Author(s):  
Minoru Arita ◽  
Nobuhiro Takashima ◽  
Yukio Ichinose ◽  
Mayumi Someno

2019 ◽  
Vol 11 (13) ◽  
pp. 3558 ◽  
Author(s):  
Swarda S. Radkar ◽  
Ali Amiri ◽  
Chad A. Ulven

There has been a substantial increase in the usage of natural fibers and biodegradable polymers in composite materials due to the recent focus on sustainability of materials. Flax fibers have exhibited higher mechanical properties compared to most other natural fibers available. However, one of the major challenges faced in the use of flax fiber is its hydrophilicity. In this study, the tensile behavior of flax fiber tows removed from commercially available woven fabrics were investigated at different moisture levels. The breaking tenacity of fiber tows was shown to increase with an increase in moisture content of up to 25%. After this point, additional absorption of moisture resulted in a decrease of fiber tenacity. In addition, the diffusion process through flax fiber mat with different areal densities was investigated and the diffusion coefficients were determined using the desorption curves. Diffusion rates were not found to significantly change with varying areal densities of 200 to 400 gsm, but were significantly different when exposed to temperatures of 55 °C versus 80 °C.


2016 ◽  
Author(s):  
M. Song ◽  
P. F. Liu ◽  
S. J. Hanna ◽  
R. A. Zaveri ◽  
K. Potter ◽  
...  

Abstract. To improve predictions of air quality, visibility, and climate change, knowledge of the viscosities and diffusion rates within organic particulate matter consisting of secondary organic material (SOM) is required.Most qualitative and quantitative measurements of viscosity and diffusion rates within organic particulate matter have focused on SOM particles generated from biogenic VOCs such as α-pinene and isoprene. In this study, we quantify the relative humidity (RH)-dependent viscosities at 295 ± 1 K of SOM produced by photo-oxidation of toluene, an anthropogenic VOC. The viscosities of toluene-derived SOM were 2 × 10−1 to ∼6 × 106 Pa·s from 30 to 90 % RH, and greater than ~2 × 108 Pa·s (similar to or greater than the viscosity of tar pitch) for RH ≤ 17 %. These viscosities correspond to Stokes-Einstein-equivalent diffusion coefficients for large organic molecules of ~2 × 10−15 cm2·s−1 for 30 % RH, and lower than ~3 × 10−17 cm2·s−1 for RH ≤ 17 %. Based on these estimated diffusion coefficients, the mixing time of large organic molecules within 200 nm toluene-derived SOM particles is 0.1–5 hr for 30 % RH, and higher than ~100 hr for RH ≤ 17 %. These results were used, as a first-order approximation, to estimate if organic particulate matter will be in well-mixed over the world's top 15 most populous megacities. If the organic particulate matter in the megacities is similar to the toluene-derived SOM in this study, in Kolkata, Istanbul, Dhaka, Tokyo, Shanghai, and Mumbai, mixing times in organic particulate matter during extended periods of the year will be very short, and well-mixed particles can be assumed. On the other hand, the mixing times of large organic molecules in organic particulate matter in Delhi, Beijing, Mexico City, Cairo, and Karachi may be long and the particles may not be well-mixed in the afternoon (3:00–5:00 local time) during certain times of the year.


1981 ◽  
Vol 12 (30) ◽  
Author(s):  
M. ARITA ◽  
N. TAKASHIMA ◽  
Y. ICHINOSE ◽  
M. SOMENO

2008 ◽  
Vol 102 (1-4) ◽  
pp. 403-409 ◽  
Author(s):  
Werner Singer ◽  
Ralph Latteck ◽  
Luis Federico Millan ◽  
Nick J. Mitchell ◽  
Jens Fiedler

2012 ◽  
Vol 433-440 ◽  
pp. 1920-1925
Author(s):  
Ze Gao Yin ◽  
Le Wang ◽  
Jin Xiong Zhang ◽  
Xian Wei Cao

In Fluent, the 3-D RNG k- ξ mathematical model is employed to compute the plug discharge, and dissolved oxygen convection and diffusion model is established to simulate the concentration distribution of dissolved oxygen with user defined scalar method. Velocity, pressure, turbulence kinetic energy, turbulence dissipation rate and dissolved oxygen concentration are computed. Then, velocity, pressure and dissolved oxygen concentration are compared with the data of physical model, and they agree with each other approximately, showing it is valid and reliable to compute the plug discharge and dissolved oxygen concentration with the coupled model. Furthermore, the characteristics of hydraulic factors including dissolved oxygen concentration are analyzed and generalized based on the computational results.


1967 ◽  
Vol 21 (1) ◽  
pp. 1-8 ◽  
Author(s):  
Edward B. Owens

This paper is a review presenting a description of the instrument and method, a brief summary of the early work, and a more detailed look at the development since 1960. Studies on the properties of photographic emulsions as ion detectors and the optimum conditions for their use are reported. Various methods are reported for quantitative data treatment, which include plate calibration, photometry, and corrections. Investigations of the spark source are reviewed, covering the causes and effects of the varying energy spectra and some corrections for the relative volatility and diffusion rates. The contribution of the sample itself to the analytical error is discussed, and the results obtained with rigorous standardization are presented.


2003 ◽  
Vol 10 (02n03) ◽  
pp. 461-466 ◽  
Author(s):  
O. Kido ◽  
C. Kaito ◽  
Y. Saito

On heating Mn-deposited Al particles (Mn–Al specimen) at 300°C, diffraction spots due to a Al86Mn14 quasicrystal appeared, in addition to those due to Al6Mn alloy. On heating a specimen of the Al-deposited Mn particles (Al–Mn specimen), Al50Mn50 alloy was formed. Neither the quasicrystal nor Al6Mn phases appeared. The electron microscope images of the Mn–Al specimen showed the existence of void clusters in the Al particles. This indicates that the alloys and the quasicrystals were produced by the diffusion of Al atoms to the Mn clusters. In the case of the Al–Mn specimen, the surface of Mn particles was covered with an Al thin film of uniform thickness. The surface Al layer changed to Al50Mn50 alloy. These results indicate that the diffusion direction of atoms and diffusion rates are different between Mn–Al and Al–Mn systems.


Sign in / Sign up

Export Citation Format

Share Document