scholarly journals MACROALGAE Fucus vesiculosus OIL: BIODIESEL PRODUCTION USING ALKALINE TRANSESTERIFICATION

Química Nova ◽  
2021 ◽  
Author(s):  
Bruno Petry ◽  
Rafael Rial ◽  
Osmar Freitas ◽  
Joyce Barbosa ◽  
Leandro Cavalheiro ◽  
...  

This work studied the obtaining of methyl biodiesel and ethyl biodiesel using alkaline transesterification from macroalgae Fucus vesiculosos oil (FVO). FVO has 86.59% of its composition in unsaturated fatty acids, with a greater quantity of linoleic acid and oleic acid, a chemical composition near the soybean oil, the most used raw material for the production of biodiesel. Linoleic acid (47.88%), and oleic acid (34.66%) are the fatty acids present in the greatest amount in FVO, and unsaturated fatty acids correspond to 86.59% the composition of FVO, a composition of fatty acids close to that of soybean oil, which is the oil most produced and used for the production of biodiesel. To obtain methyl biodiesel (MBFVO) and ethyl biodiesel (EBFVO) the molar ratio oil: alcohol 1: 3 and 1% alkaline catalyst, NaOH, was used. The yield of the transesterification reaction was evaluated by varying the reaction time between 30 and 60 minutes and the highest yields were obtained after 60 minutes of reaction. In order to check the quality of the obtained biodiesel, the properties acidity index, iodine value, water content, specific mass at 20 o C, oxidative stability, cold filter lugging point and kinematic viscosity were evaluated. The oxidative stability had an induction period below the recommended, but it can be corrected with the addition of antioxidants to the biodiesel. All other physical and chemical properties had values within the stipulated by the regulatory agencies, indicating that the macroalgae Fucus vesiculosus can be a raw material in potential for production of biodiesel

2021 ◽  
Vol 3 (4) ◽  
pp. 19-24
Author(s):  
Asya Çetinkaya

In this study, it was aimed to determine the effect of some production parameters on the characteristics of butters made from whey, which is an important dairy by-product, and creams obtained from milk. The acidity values of milk, whey, cream, and butter were respectively detected as 0.17±0.00%, 0.13±0.01%, 0.22±0.01%, 0.24±0.01%, 0.26±0.00%, 0.25±0.01%, fat values were respectively detected as; 3.50±0.14%, 0.60±0.19%, 39.0±0.34%, 43.0±0.35%, 80.0±0.46%, 84.0±0.42% and protein values were respectively detected as; 3.30±0.19%, 0.68±0.03%, 0.93±0.12%, 0.54±0.03%, 0.51±0.02%, 0.58±0.00%. 10 saturated and 7 unsaturated fatty acids were detected in cream and whey butter samples. It was seen that the most common fatty acids were palmitic, stearic, myristic and oleic acid, and the amount of oleic, stearic and linoleic acid was higher in whey butter. In conclusion, we can state that whey, which is an important dairy residue, can be used as an alternative raw material in butter production.


1992 ◽  
Vol 285 (2) ◽  
pp. 557-562 ◽  
Author(s):  
T Liang ◽  
S Liao

Human or rat microsomal 5 alpha-reductase activity, as measured by enzymic conversion of testosterone into 5 alpha-dihydrotestosterone or by binding of a competitive inhibitor, [3H]17 beta-NN-diethulcarbamoyl-4-methyl-4-aza-5 alpha-androstan-3-one ([3H]4-MA) to the reductase, is inhibited by low concentrations (less than 10 microM) of certain polyunsaturated fatty acids. The relative inhibitory potencies of unsaturated fatty acids are, in decreasing order: gamma-linolenic acid greater than cis-4,7,10,13,16,19-docosahexaenoic acid = cis-6,9,12,15-octatetraenoic acid = arachidonic acid = alpha-linolenic acid greater than linoleic acid greater than palmitoleic acid greater than oleic acid greater than myristoleic acid. Other unsaturated fatty acids such as undecylenic acid, erucic acid and nervonic acid, are inactive. The methyl esters and alcohol analogues of these compounds, glycerols, phospholipids, saturated fatty acids, retinoids and carotenes were inactive even at 0.2 mM. The results of the binding assay and the enzymic assay correlated well except for elaidic acid and linolelaidic acid, the trans isomers of oleic acid and linoleic acid respectively, which were much less active than their cis isomers in the binding assay but were as potent in the enzymic assay. gamma-Linolenic acid had no effect on the activities of two other rat liver microsomal enzymes: NADH:menadione reductase and glucuronosyl transferase. gamma-Linolenic acid, the most potent inhibitor tested, decreased the Vmax. and increased Km values of substrates, NADPH and testosterone, and promoted dissociation of [3H]4-MA from the microsomal reductase. gamma-Linolenic acid, but not the corresponding saturated fatty acid (stearic acid), inhibited the 5 alpha-reductase activity, but not the 17 beta-dehydrogenase activity, of human prostate cancer cells in culture. These results suggest that unsaturated fatty acids may play an important role in regulating androgen action in target cells.


2014 ◽  
Vol 32 (2) ◽  
pp. 255-265 ◽  
Author(s):  
Omar Montenegro R. ◽  
Stanislav Magnitskiy ◽  
Martha C. Henao T.

This study was conducted to assess fruit and seed yield, oil content and oil composition of Jatropha curcas fertilized with different doses of nitrogen and potassium in Espinal (Tolima, Colombia). The yields ranged from 4,570 to 8,800 kg ha-1 of fruits and from 2,430 to 4,746 kg ha-1 of seeds. These yields showed that the fertilizer dose of 150 kg ha-1 N + 120 kg ha-1K increased fruit production by 92% and seed production by 95%, which represents an increase of about 100% in oil production, which increased from 947 to 1,900 kg ha-1. The total oil content in the seeds ranged from 38.7 to 40.1% (w/w) with a high content of the unsaturated fatty acids oleic (> 47%) and linoleic acid (> 29%). The highest content of oleic acid in the seed oil was from the unfertilized control plants and plants with an application of 100 kg ha-1 of N and 60 kg ha-1 of K, with an average of 48%. The lowest content of oleic acid was registered when a low dose of nitrogen and a high level of potassium were applied at a ratio of 1:2.4 and doses of 50 kg ha-1 N + 120 kg ha-1 K, respectively. Low contents of the saturated fatty acids palmitic (13.4%) and stearic (7.26%) were obtained, making this oil suitable for biodiesel production. The nitrogen was a more important nutrient for the production and quality of oil in J. curcas than potassium under the studied conditions of soil and climate.


2014 ◽  
Vol 39 (1) ◽  
pp. 192
Author(s):  
Valter Ortiz Lace ◽  
Isabel Matos Fraga ◽  
José Ricardo Castrillon Fernandez ◽  
Cláudia Roberta Gonçalves

This study aimed to the methyl biodiesel production by transesterification reaction via alkaline catalysis, using as a raw material alternative to soybean oil commonly used, coco-da-baía oil (Cocos nucifera L). The biodiesel was characterized as to its acidity, density, humidity, ester content, flash point, glycerol (free, total, mono-, di- and triglycerides) and maximum percentage of methanol. The oil used was characterized by acid value, saponification number, fatty acids, density and humidity. Through these results, we verified the quality of the obtained biofuel.


2014 ◽  
Vol 139 (4) ◽  
pp. 433-441 ◽  
Author(s):  
Geoffrey Meru ◽  
Cecilia McGregor

Seed oil percentage (SOP) and fatty acid composition of watermelon (Citrullus lanatus) seeds are important traits in Africa, the Middle East, and Asia where the seeds provide a significant source of nutrition and income. Oil yield from watermelon seed exceeds 50% (w/w) and is high in unsaturated fatty acids, a profile comparable to that of sunflower (Helianthus annuus) and soybean (Glycine max) oil. As a result of novel non-food uses of plant-derived oils, there is an increasing need for more sources of vegetable oil. To improve the nutritive value of watermelon seed and position watermelon as a potential oil crop, it is critical to understand the genetic factors associated with SOP and fatty acid composition. Although the fatty acid composition of watermelon seed is well documented, the underlying genetic basis has not yet been studied. Therefore, the current study aimed to elucidate the quality of watermelon seed oil and identify genomic regions and candidate genes associated with fatty acid composition. Seed from an F2 population developed from a cross between an egusi type (PI 560023), known for its high SOP, and Strain II (PI 279261) was phenotyped for palmitic acid (16:0), stearic acid (18:0), oleic acid (18:1), and linoleic acid (18:2). Significant (P < 0.05) correlations were found between palmitic and oleic acid (0.24), palmitic and linoleic acid (–0.37), stearic and linoleic acid (–0.21), and oleic and linoleic acid (–0.92). A total of eight quantitative trait loci (QTL) were associated with fatty acid composition with a QTL for oleic and linoleic acid colocalizing on chromosome (Chr) 6. Eighty genes involved in fatty biosynthesis including those modulating the ratio of saturated and unsaturated fatty acids were identified from the functionally annotated genes on the watermelon draft genome. Several fatty acid biosynthesis genes were found within and in close proximity to the QTL identified in this study. A gene (Cla013264) homolog to fatty acid elongase (FAE) was found within the 1.5-likelihood-odds (LOD) interval of the QTL for palmitic acid (R2 = 7.6%) on Chr 2, whereas Cla008157, a homolog to omega-3-fatty acid desaturase and Cla008263, a homolog to FAE, were identified within the 1.5-LOD interval of the QTL for palmitic acid (R2 = 24.7%) on Chr 3. In addition, the QTL for palmitic acid on Chr 3 was located ≈0.60 Mbp from Cla002633, a gene homolog to fatty acyl- [acyl carrier protein (ACP)] thioesterase B. A gene (Cla009335) homolog to ACP was found within the flanking markers of the QTL for oleic acid (R2 = 17.9%) and linoleic acid (R2 = 21.5%) on Chr 6, whereas Cla010780, a gene homolog to acyl-ACP desaturase was located within the QTL for stearic acid (R2 = 10.2%) on Chr 7. On Chr 8, another gene (Cla013862) homolog to acyl-ACP desaturase was found within the 1.5-LOD interval of the QTL for oleic acid (R2 = 13.5%). The genes identified in this study are possible candidates for the development of functional markers for application in marker-assisted selection for fatty acid composition in watermelon seed. To the best of our knowledge, this is the first study that aimed to elucidate genetic control of the fatty acid composition of watermelon seed.


2004 ◽  
Vol 58 (2) ◽  
pp. 73-78 ◽  
Author(s):  
Dejan Skala ◽  
Sandra Glisic

Biodiesel is defined as a fuel which may be used as pure biofuel or at high concentration in mineral oil derivatives, in accordance with specific quality standards for transport applications. The main raw material used for biodiesel production is rapeseed, which contains mono-unsaturated acids (about 60%) and also poly-unsaturated fatty acids (C 18:1 and C 18:3) in a lower quantity, as well as some undesired saturated fatty acids (palmitic and stearic acids). Other raw materials have also been used in research and the industrial production of biodiesel (palm oil, sunflower oil, soybean oil, waste plant oil, animal fats, etc). The historical background of biodiesel production, installed industrial capacities, as well as the Directive of the European Parliament and of the Council (May 2003) regarding the promotion of the use of biofuels or other renewable fuels for transport are discussed in the first part of this article. The second part focuses on some new concepts for the future development of technology for biodiesel production, based on the application of non-catalytic transesterification under supercritical conditions or the use of lipases as an alternative catalyst for this reaction.


Author(s):  
M. Ruths ◽  
S. Lundgren ◽  
K. Danerlo¨v ◽  
K. Persson

We have measured normal and lateral (friction) forces across films of saturated and unsaturated fatty acids with the Surface Forces Apparatus (SFA). When adsorbed onto mica from n-hexadecane, linoleic acid forms a dimer layer between monolayer-covered surfaces. This dimer layer, which is not observed in stearic or oleic acid, is removed at low loads. The remaining linoleic acid monolayers are thinner than the ones formed by stearic and oleic acid, and show a more complex friction response with two regimes of linear friction, higher stability at very high loads, and a dependence of the friction on sliding speed and adsorption time.


2017 ◽  
Vol 83 (9) ◽  
Author(s):  
Woo-Ri Kang ◽  
Min-Ju Seo ◽  
Kyung-Chul Shin ◽  
Jin-Byung Park ◽  
Deok-Kun Oh

ABSTRACT Oleate hydratases (OhyAs) catalyze the conversion of unsaturated fatty acids to 10-hydroxy fatty acids, which are used as precursors of important industrial compounds, including lactones and ω-hydroxycarboxylic and α,ω-dicarboxylic acids. The genes encoding OhyA and a putative fatty acid hydratase in Stenotrophomonas maltophilia were identified by genomic analysis. The putative fatty acid hydratase was purified and identified as an oleate hydratase (OhyA2) based on its substrate specificity. The activity of OhyA2 as a holoenzyme was not affected by adding cofactors, whereas the activity of the original oleate hydratase (OhyA1) showed an increase. Thus, all characterized OhyAs were categorized as either OhyA1 or OhyA2 based on the activities of holoenzymes upon adding cofactors, which were determined by the type of the fourth conserved amino acid of flavin adenine dinucleotide (FAD)-binding motif. The hydration activities of S. maltophilia OhyA2 toward unsaturated fatty acids, including oleic acid, palmitoleic acid, linoleic acid, α-linolenic acid, and γ-linolenic acid, were greater than those of OhyA1. Moreover, the specific activity of S. maltophilia OhyA2 toward unsaturated fatty acids, with the exception of γ-linolenic acid, was the highest among all reported OhyAs. IMPORTANCE All characterized OhyAs were categorized as OhyA1s or OhyA2s based on the different properties of the reported and newly identified holo-OhyAs in S. maltophilia upon the addition of cofactors. OhyA2s showed higher activities toward polyunsaturated fatty acids (PUFAs), including linoleic acid, α-linolenic acid, and γ-linolenic acid, than those of OhyA1s. This suggests that OhyA2s can be used more effectively to convert plant oils to 10-hydroxy fatty acids because plant oils contain not only oleic acid but also PUFAs. The hydration activity of the newly identified OhyA2 from S. maltophilia toward oleic acid was the highest among the activity levels reported so far. Therefore, this enzyme is an efficient biocatalyst for the conversion of plant oils to 10-hydroxy fatty acids, which can be further converted to important industrial materials.


2010 ◽  
Vol 79 (9) ◽  
pp. S21-S28 ◽  
Author(s):  
Tereza Krejčí-Treu ◽  
Eva Straková ◽  
Pavel Suchý ◽  
Ivan Herzig

The main objective of this work was to compare the effect of six vegetable oils added to feeding mixtures that were administered to broiler chickens on the content of major fatty acids in chicken meat. The experiment started with 90 one-day-old Ross 308 meat hybrid male chickens that were divided into six groups. Chickens were fed complete feeding mixtures for the prefattening (BR1), fattening (BR2), and post-fattening (BR3) of broiler chickens. The BR1 feeding mixture was administered to chickens aged 1-10 days, the BR2 feeding mixture was given from Day 11 to Day 30, and the BR3 feeding mixture was then administered until Day 42. The BR1 feeding mixture that was administered to all six groups during the first ten days of the experiment was supplemented with soybean oil. BR2 and BR3 feeding mixtures used to feed chickens aged 11-42 days were fortified with soybean oil (SO Group), rapeseed oil (RO Group), sunflower oil (SFO Group), flaxseed oil (FO Group), olive oil (OO Group), and evening primrose oil (EPO Group). The vegetable oils used differed by the composition of fatty acids, particularly by the content of oleic acid, linoleic acid, α-linolenic acid. The use of the above-described experimental diets in young broilers from Day 11 to 42 had a significant effect on the content of fatty acids in the fat from breast and thigh muscles. The content of α-linolenic acid in breast and thigh muscles of broilers that received the feed containing flaxseed oil (21.16 g/100 g of oil and 17.13 g/100 g of oil, respectively) significantly increased (p ⪬ 0.01). The highest content of linoleic acid (p ⪬ 0.01) in breast and thigh muscles was found in chickens that were fed the feed containing primrose oil (59.13 g/100 g and 51.71 g/100 g). A significant increase (p ⪬ 0.01) in the level of oleic acid was detected in both breast and thigh muscles of broilers that received olive oil fortified feed (52.44 g/100 g and 43.70 g/100 g of oil). No significant variation was found in the content of palmitic acid and palmitooleic acid. The levels of oleic acid, linoleic acid and α-linolenic acid in feeding mixtures correlated with those found in breast and thigh muscles (r = 0.88; 0.94 and 0.99; r = 0.99; 0.98 and 0.99).


2021 ◽  
pp. 346-362
Author(s):  
Salim Najmaldain Saber ◽  
Hikmat Ali Mohamad ◽  
Madzlan Aziz

The core objective of this study was to investigate the physicochemical characteristics and fatty acid composition of the oils of sunflower, olive, virgin coconut and ginger oils, as well as the separation of their unsaturated fatty acids. The data indicated a significant variation in physicochemical properties (acid, saponification, ester, and iodine values) among oils. Transesterification process was carried out at a molar ratio of 1:7:0.1 of oil: methanol: KOH. Fatty acid methyl esters of oils were analyzed by infrared (IR) and gas chromatography–mass (GC-MS) spectrometry. Twelve fatty acids were identified, where the major fatty acid of  olive oil was found to be  oleic acid (89%), whereas those of sunflower and ginger oils were linoleic acid (80.9 %) and (79.3 %), respectively. Sunflower and olive oils were fractionated by 25% silver nitrate-impregnated silica gel column chromatography. By this method, linoleic acid methyl ester from sunflower and oleic acid methyl ester from olive oil were isolated with high purity percentages and yields. This study is significant for the development of food and pharmaceutical products.


Sign in / Sign up

Export Citation Format

Share Document