VOC Fate Model Verification at Multiple Pulp Mill Wastewater Treatment Sites

1992 ◽  
Vol 26 (1-2) ◽  
pp. 407-415 ◽  
Author(s):  
D. A. Barton ◽  
J. J. McKeown ◽  
W. Chudyk
Keyword(s):  
Wastewater Treatment ◽  
Paper Industry ◽  
Pulp Mill ◽  
Pulp And Paper Industry ◽  
Model Verification ◽  
Initial Model ◽  
Gas Sampling ◽  
Treatment Processes ◽  
Fate Model

A model of organic compound removal by biological wastewater treatment processes receiving pulp and paper industry wastewaters has been developed and initial model verification performed at a single mill site. This paper presents the results of further model verification conducted at multiple mill sites, including replication of the original site. In addition, VOC losses at other unit processes are quantified. Activated sludge basin chloroform volatilization rates are predicted to within twelve percent of the measured rates. Predicted overall methanol removals are consistent with observed removals although difficulties encountered during off-gas sampling preclude determination of the extent of removal due to volatilization.

Rapid determination of fractal structure of bacterial assemblages in wastewater treatment: implications to process optimisation

1998 ◽  
Vol 38 (2) ◽  
pp. 9-15 ◽  
Author(s):  
J. Guan ◽  
T. D. Waite ◽  
R. Amal ◽  
H. Bustamante ◽  
R. Wukasch
Keyword(s):  
Wastewater Treatment ◽  
Fractal Structure ◽  
Structural Information ◽  
Rapid Determination ◽  
Fractal Dimensions ◽  
Structure Information ◽  
Treatment Processes ◽  
On Line ◽  
Bacterial Aggregates

A rapid method of determining the structure of aggregated particles using small angle laser light scattering is applied here to assemblages of bacteria from wastewater treatment systems. The structure information so obtained is suggestive of fractal behaviour as found by other methods. Strong dependencies are shown to exist between the fractal structure of the bacterial aggregates and the behaviour of the biosolids in zone settling and dewatering by both pressure filtration and centrifugation methods. More rapid settling and significantly higher solids contents are achievable for “looser” flocs characterised by lower fractal dimensions. The rapidity of determination of structural information and the strong dependencies of the effectiveness of a number of wastewater treatment processes on aggregate structure suggests that this method may be particularly useful as an on-line control tool.

Evaluation of the Potential of Waste from Pulp Production (Grits) in its Use in Mortar: Physical and Chemical Characterization

2015 ◽  
Vol 820 ◽  
pp. 583-587
Author(s):  
Leonardo Carvalho Mesquita ◽  
Rita de Cássia S. Sant’ana Alvarenga ◽  
Carol Ferreira Rezende Santos ◽  
Adonys Natan Oliveira Alvares ◽  
Ana Augusta Passos Rezende ◽  
...  
Keyword(s):  
Paper Industry ◽  
Chemical Characterization ◽  
Pulp And Paper Industry ◽  
Kraft Process ◽  
Physical And Chemical Characterization ◽  
Absorption Determination ◽  
Potential Alternative ◽  
Physical And Chemical ◽  
Chemical Testing

The grits is an inorganic solid residue generated during the Kraft process by the pulp and paper industry, which presents in its composition the main ingredients of Portland cement. According to some authors, the grits can be classified as a non inert, non hazardous, granular solid industrial waste. With this in mind, a study was proposed with the objective of evaluating, initially, the applicability of grits in mortar, by means of physical and chemical testing. The physical evaluations were realized through the following tests: determination of bulk gravity saturated - surface - dry (SSD) and water absorption; determination of the pulverulent material content; and the determination of particle size distribution. To chemically test the grits, a reading of the metal concentrations present in the grits was realized as well as an analysis of the leaching and solubilization extracts. It was concluded that the addition of grits to mortar is a potential alternative.

Energy efficient aeration of wastewaters from the pulp and paper industry

2010 ◽  
Vol 62 (10) ◽  
pp. 2364-2371 ◽  
Author(s):  
M. Sandberg
Keyword(s):  
Oxygen Transfer ◽  
Biological Treatment ◽  
Bubble Column ◽  
Paper Industry ◽  
Electrical Power ◽  
Treatment Plant ◽  
Pulp Mill ◽  
Pulp And Paper Industry ◽  
Pulp And Paper ◽  
Paper Mills

More than 50% of the electrical power needed to treat pulp and paper industry effluents is used for aeration in biological treatment stages. A large share of the oxygen that passes through the wastewater is not consumed and will be found in the off-gas. Energy can be saved by aerating under conditions where the oxygen transfer is most efficient, for example at low concentrations of dissolved oxygen Consider the sludge as an energy source; electricity can be saved by avoiding sludge reduction through prolonged aeration. High oxygen transfer efficiency can be retained by using the oxygen consumption of biosolids. Quantified savings in the form of needed volumes of air while still achieving sufficient COD reduction are presented. The tests have been made in a bubble column with pulp mill process water and sludge from a biological treatment plant. These were supplemented with case studies at three pulp and paper mills.

Sign in / Sign up

Export Citation Format

Share Document