Bioremediation of trichloroethylene contaminated groundwater using anaerobic process

2008 ◽  
Vol 58 (11) ◽  
pp. 2127-2132 ◽  
Author(s):  
Cheema Chomsurin ◽  
Juthathip Kajorntraidej ◽  
Kongrit Luangmuang
Keyword(s):  
Contaminated Soil ◽  
Reductive Dechlorination ◽  
Volatile Fatty Acids ◽  
Low Cost ◽  
Ammonia Nitrogen ◽  
Electron Donors ◽  
Contaminated Groundwater ◽  
Peanut Shell ◽  
Fermentation System ◽  
Set Up

Anaerobic remediation of trichloroethylene (TCE) contaminated soil and groundwater was studied in laboratory setups. In this process fermentation of polymeric organic materials (POMS) produced volatile fatty acids (VFAs) that were electron donors in reductive dechlorination of TCE. Shredded peanut shell was selected as low cost POM and the experiments were set up in 500 ml Erlenmeyer flasks. In the setups, approximately 25 mg of leachate contaminated soil was used as the main source of microorganisms and about 5 g of shredded peanut shell (0.5–2.36 mm) was added to produce VFAs for dechlorination of TCE. In the first set of experiments, fermentation of soil and shredded peanut shell was studied and it was found that VFAs were produced continuously with increasing concentration (5.63 mM as CH3COOH from the first day to 17.17 in the 10th day of the experiment). During the fermentation, concentration of ammonia-nitrogen was 22–50 mg/L, the ratio of VFA to NH3 was 15.29–23.44 and pH was 5.24–6.00. These results show that the system was appropriate for microorganism activities. In the second set of experiments, TCE (∼48 mg/L) was added to the fermentation system and remediation of TCE by reductive dechlorination was studied. It was found that 0.04(±0.01) mg TCE adsorbed to a gram of soil and peanut shells at the beginning of the experiment and based on mass balance of the system, TCE concentration in water was linearly reduced at the rate of 0.0098 mg/hr.

scholarly journals A Microcosm Treatability Study for Evaluating Wood Mulch-Based Amendments as Electron Donors for Trichloroethene (TCE) Reductive Dechlorination

Water ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 1949
Author(s):  
Edoardo Masut ◽  
Alessandro Battaglia ◽  
Luca Ferioli ◽  
Anna Legnani ◽  
Carolina Cruz Viggi ◽  
...  
Keyword(s):  
Electron Donor ◽  
Environmental Sustainability ◽  
Reductive Dechlorination ◽  
Environmental Remediation ◽  
Low Cost ◽  
Chlorinated Solvents ◽  
Electron Donors ◽  
Chlorinated Ethenes ◽  
Dehalococcoides Mccartyi ◽  
Wood Mulch

In this study, wood mulch-based amendments were tested in a bench-scale microcosm experiment in order to assess the treatability of saturated soils and groundwater from an industrial site contaminated by chlorinated ethenes. Wood mulch was tested alone as the only electron donor in order to assess its potential for stimulating the biological reductive dechlorination. It was also tested in combination with millimetric iron filings in order to assess the ability of the additive to accelerate/improve the bioremediation process. The efficacy of the selected amendments was compared with that of unamended control microcosms. The results demonstrated that wood mulch is an effective natural and low-cost electron donor to stimulate the complete reductive dechlorination of chlorinated solvents to ethene. Being a side-product of the wood industry, mulch can be used in environmental remediation, an approach which perfectly fits the principles of circular economy and addresses the compelling needs of a sustainable and low environmental impact remediation. The efficacy of mulch was further improved by the co-presence of iron filings, which accelerated the conversion of vinyl chloride into the ethene by increasing the H2 availability rather than by catalyzing the direct abiotic dechlorination of contaminants. Chemical analyses were corroborated by biomolecular assays, which confirmed the stimulatory effect of the selected amendments on the abundance of Dehalococcoides mccartyi and related reductive dehalogenase genes. Overall, this paper further highlights the application potential and environmental sustainability of wood mulch-based amendments as low-cost electron donors for the biological treatment of chlorinated ethenes.

scholarly journals Multiple-factor associative effects of peanut shell combined with alfalfa and concentrate determined by in vitro gas production method

2019 ◽  
Vol 64 (No. 8) ◽  
pp. 352-360
Author(s):  
Jiu Yuan ◽  
Xinjie Wan
Keyword(s):  
Fatty Acids ◽  
Volatile Fatty Acids ◽  
Rumen Fluid ◽  
Production Method ◽  
Ammonia Nitrogen ◽  
Gas Production ◽  
Peanut Shell ◽  
Dry Matter Digestibility ◽  
In Vitro Gas Production

The associative effects (AE) between concentrate (C), peanut shell (P) and alfalfa (A) were investigated by means of an automated gas production (GP) system. The C, P and A were incubated alone or as 40 : 60 : 0, 40 : 45 : 15, 40 : 30 : 30, 40 : 15 : 45, 40 : 0 : 60 and 30 : 70 : 0, 30 : 55 : 15, 30 : 40 : 30, 30 : 25 : 45, 30 : 10 : 60, 30 : 0 : 70 mixtures where the C : roughage (R) ratios were 40 : 60 and 30 : 70. Samples (0.2000 ± 0.0010 g) of single feeds or mixtures were incubated for 96 h in individual bottles (100 ml) with 30 ml of buffered rumen fluid. GP parameters were analysed using a single exponential equation. After incubation, the residues were used to determine pH, dry matter digestibility (DMD), organic matter digestibility (OMD), volatile fatty acids (VFA) and ammonia nitrogen (NH<sub>3</sub>-N) of the incubation fluid, and their single factor AE indices (SFAEI) and multiple-factors AE indices (MFAEI) were determined. The results showed that group of 30 peanut shell had higher SFAEI of GP<sub>48 h</sub>, DMD, OMD and total volatile fatty acids (p &lt; 0.05) and MFAEI (p &lt; 0.05) than groups 60, 45 and 0 when C : R was 40 : 60. The group of 10 peanut shell showed higher SFAEI of GP<sub>48 h</sub>, DMD and OMD (p &lt; 0.05) than groups 70, 55 and 40 and MFAEI (p &lt; 0.01) when C : R was 30 : 70. It is concluded that optimal SFAEI and MFAEI were obtained when the C : P : A ratios were 40 : 30 : 30 and 30 : 10 : 60.

Use of poly-β-hydroxy-butyrate as a slow-release electron donor for the microbial reductive dechlorination of TCE

2008 ◽  
Vol 57 (6) ◽  
pp. 921-925 ◽  
Author(s):  
F. Aulenta ◽  
M. Fuoco ◽  
A. Canosa ◽  
M. Petrangeli Papini ◽  
M. Majone
Keyword(s):  
Electron Donor ◽  
Biodegradable Polymer ◽  
Reductive Dechlorination ◽  
Slow Release ◽  
Low Cost ◽  
Electron Donors ◽  
Microbial Reductive Dechlorination ◽  
Reducing Equivalents

In situ anaerobic reductive dechlorination, using slow-release electron donors, is emerging as an effective and sustainable (low-cost and low-maintenance) technology to remediate aquifers contaminated by chloroethenes. In the present study, we investigated the use of poly-β-hydroxy-butyrate (PHB), a fully biodegradable polymer, as a slow-release source of hydrogen and acetate for the reductive dechlorination of trichloroethene (TCE). Results of this study indicated that TCE dechlorination in PHB-amended microcosms was 2.3-times higher than in non-amended controls. This higher activity was explained by a higher H2 level in PHB-amended microcosms. As usual, acetate was the major sink (∼90%) of reducing equivalents available from PHB degradation, whereas no acetotrophic dechlorination was observed.

VOLATILE FATTY ACIDS AS ELECTRON DONORS FOR THE REDUCTIVE DECHLORINATION OF CHLOROETHENES

2002 ◽  
Vol 37 (4) ◽  
pp. 439-449 ◽  
Author(s):  
Xiao-Xia Lu ◽  
Guang-He Li ◽  
Shu Tao ◽  
Tom Bosma ◽  
Jan Gerritse
Keyword(s):  
Fatty Acids ◽  
Reductive Dechlorination ◽  
Volatile Fatty Acids ◽  
Electron Donors

Development of a Capacitor Probe to Detect Subsurface Deterioration in Concrete

1997 ◽  
Vol 503 ◽  
Author(s):  
B. K. Diefenderfer ◽  
I. L. Al-Qadi ◽  
J. J. Yoho ◽  
S. M. Riad ◽  
A. Loulizi
Keyword(s):  
Dielectric Constant ◽  
Portland Cement ◽  
Electromagnetic Waves ◽  
Low Cost ◽  
Complex Dielectric Constant ◽  
Life Cycle Costs ◽  
Parallel Plates ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Set Up

ABSTRACTPortland cement concrete (PCC) structures deteriorate with age and need to be maintained or replaced. Early detection of deterioration in PCC (e.g., alkali-silica reaction, freeze/thaw damage, or chloride presence) can lead to significant reductions in maintenance costs. However, it is often too late to perform low-cost preventative maintenance by the time deterioration becomes evident. By developing techniques that would enable civil engineers to evaluate PCC structures and detect deterioration at early stages (without causing further damage), optimization of life-cycle costs of the constructed facility and minimization of disturbance to the facility users can be achieved.Nondestructive evaluation (NDE) methods are potentially one of the most useful techniques ever developed for assessing constructed facilities. They are noninvasive and can be performed rapidly. Portland cement concrete can be nondestructively evaluated by electrically characterizing its complex dielectric constant. The real part of the dielectric constant depicts the velocity of electromagnetic waves in PCC. The imaginary part, termed the “loss factor,” describes the conductivity of PCC and the attenuation of electromagnetic waves.Dielectric properties of PCC have been investigated in a laboratory setting using a parallel plate capacitor operating in the frequency range of 0.1 to 40.1MIHz. This capacitor set-up consists of two horizontal-parallel plates with an adjustable separation for insertion of a dielectric specimen (PCC). While useful in research, this approach is not practical for field implementation. A new capacitor probe has been developed which consists of two plates, located within the same horizontal plane, for placement upon the specimen to be tested. Preliminary results show that this technique is feasible and results are promising; further testing and evaluation is currently underway.

Fault Localization of Power-Ground Short via Signal Injection and Oscilloscope Technique

2010 ◽  
Author(s):  
Binh Nguyen
Keyword(s):  
Low Cost ◽  
Short Circuit ◽  
Fault Localization ◽  
Fault Isolation ◽  
Test Apparatus ◽  
Good Working ◽  
Signal Injection ◽  
Set Up ◽  
Non Destructive ◽  
Short Circuit Condition

Abstract For those attempting fault isolation on computer motherboard power-ground short issues, the optimal technique should utilize existing test equipment available in the debug facility, requiring no specialty equipment as well as needing a minimum of training to use effectively. The test apparatus should be both easy to set up and easy to use. This article describes the signal injection and oscilloscope technique which meets the above requirements. The signal injection and oscilloscope technique is based on the application of Ohm's law in a short-circuit condition. Two experiments were conducted to prove the effectiveness of these techniques. Both experiments simulate a short-circuit condition on the VCC3 power rail of a good working PC motherboard and then apply the signal injection and oscilloscope technique to localize the short. The technique described is a simple, low cost and non-destructive method that helps to find the location of the power-ground short quickly and effectively.

Distribution of heterotrophic and autotrophic organisms in a biological aerated filter

2008 ◽  
Vol 3 (3) ◽  
Author(s):  
O. González-Barceló ◽  
S. González-Martínez
Keyword(s):  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Low Cost ◽  
Ammonia Nitrogen ◽  
Organic Load ◽  
Homogeneous Distribution ◽  
Municipal Wastewater Treatment ◽  
Filter Media ◽  
Aerated Filter ◽  
Secondary Settling

Biological aerated filtration is a viable option for small municipal wastewater treatment plants. A low cost filter media was obtained by triturating volcanic rock. An apparent porosity of 46 % and a specific surface area of 395 m2/m3·d were obtained once the filter was packed by using a grain size of 8.2 mm. The performance of the system, operated as a biological filter, was evaluated under an average organic load of 2.6±0.4 kgCODT/m3·d (6.7±1.1 gCODT/m2·d) without primary and secondary settling. The average CODT decreased from 220 mg/l in the influent to 88 mg/l in the effluent and the CODD was decreased from 148 mg/l in the influent to 50 mg/l in the effluent. The filter media, in combination with the biofilm, allowed a 75 % TSS removal. The ammonia nitrogen decreased from 51 mg/l in the influent to 33 mg/l in the effluent. The maximum flux coefficients of 9.3gCODdissolved/m2·d and 2.9gNH4-N/m2·d at the biofilm surface were used to simulate, with the Michaelis-Menten model, the profiles of dissolved COD, ammonium and nitrates through the aerated filter. It was possible to conclude that the backwashing procedure removed the excess biomass and was responsible for a homogeneous distribution of heterotrophic and autotrophic microorganisms along the filter depth.

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

scholarly journals Innovative passive reinforcements for the gradual stabilization of a landslide according with the observational method

Landslides ◽  
2021 ◽  
Author(s):  
Lorenzo Brezzi ◽  
Alberto Bisson ◽  
Davide Pasa ◽  
Simonetta Cola
Keyword(s):  
Monitoring System ◽  
Low Cost ◽  
Economic Losses ◽  
Fe Model ◽  
Site Conditions ◽  
Observational Method ◽  
Rainy Period ◽  
Sustainable Solutions ◽  
Before And After ◽  
Set Up

AbstractA large number of landslides occur in North-Eastern Italy during every rainy period due to the particular hydrogeological conditions of this area. Even if there are no casualties, the economic losses are often significant, and municipalities frequently do not have sufficient financial resources to repair the damage and stabilize all the unstable slopes. In this regard, the research for more economically sustainable solutions is a crucial challenge. Floating composite anchors are an innovative and low-cost technique set up for slope stabilization: it consists in the use of passive sub-horizontal reinforcements, obtained by coupling a traditional self-drilling bar with some tendons cemented inside it. This work concerns the application of this technique according to the observational method described within the Italian and European technical codes and mainly recommended for the design of geotechnical works, especially when performed in highly uncertain site conditions. The observational method prescribes designing an intervention and, at the same time, using a monitoring system in order to correct and adapt the project during realization of the works on the basis of new data acquired while on site. The case study is the landslide of Cischele, a medium landslide which occurred in 2010 after an exceptional heavy rainy period. In 2015, some floating composite anchors were installed to slow down the movement, even if, due to a limited budget, they were not enough to ensure the complete stabilization of the slope. Thanks to a monitoring system installed in the meantime, it is now possible to have a comparison between the site conditions before and after the intervention. This allows the evaluation of benefits achieved with the reinforcements and, at the same time, the assessment of additional improvements. Two stabilization scenarios are studied through an FE model: the first includes the stabilization system built in 2015, while the second evaluates a new solution proposed to further increase the slope stability.

Sign in / Sign up

Export Citation Format

Share Document