scholarly journals Влияние адгезии на трение качения и скольжения: эксперимент

2022 ◽  
Vol 92 (1) ◽  
pp. 161
Author(s):  
Я.А. Ляшенко ◽  
В.Л. Попов
Keyword(s):  
Friction Force ◽  
Sliding Friction ◽  
Rolling Friction ◽  
Tangential Component ◽  
Adhesive Properties ◽  
Stick Slip ◽  
Friction Mode ◽  
Cylindrical Steel ◽  
Good Coincidence ◽  
Chalk Dust

Normal and tangential contact between a cylindrical steel indenter (wheel) and an elastomer with high adhesive properties is investigated. In the case of indentation in the normal direction, a computer simulation of the process of indentation and detachment was carried out, which shows good coincidence with an experiment. For the rolling friction mode, when analyzing the measured dependences of the tangential component of the contact force on the wheel displacement, the adhesive component of the friction force was determined. The situation of sliding friction, in which the rotation of the wheel was impossible, is considered. In the presence of adhesion, the sliding friction force is proportional to the contact area. In the absence of adhesion (the elastomer is covered with a chalk dust), a stick-slip friction mode is realized. The frequency and amplitude of stick-slip transitions depend on the indentation depth of the indenter into the elastomer.

ON THE FRICTION OF INFLATED RUBBER TIRES ON ICE

1958 ◽  
Vol 36 (5) ◽  
pp. 599-610 ◽  
Author(s):  
C. D. Niven
Keyword(s):  
Friction Force ◽  
Coefficient Of Friction ◽  
Sliding Friction ◽  
Rolling Friction ◽  
The Other ◽  
Slow Speed ◽  
Dry Ice ◽  
Load Axis ◽  
Cold Room ◽  
The Coefficient Of Friction

The friction on ice of some small inflated rubber tires was measured on a turntable in a cold room. When rolling-friction force was plotted against load, the relation was either linear or slightly curved away from the load axis; such curvature implies that Thirion's Law does not hold for rolling friction. On the other hand when sliding-friction force was plotted against load the curvature was toward the load axis as would be expected if Thirion's Law applied. The coefficient of friction can go as low as 0.01 or even lower for a hard-pumped tire when the temperature is near 0 °C, but at −1 °C. rolling friction on dry ice is quite appreciable. The results refer only to measurements at very slow speed.

Rolling-Friction Behavior of Sub-Micron Polystyrene-Sphere Arrays under Very Light Loads

2013 ◽  
Vol 321-324 ◽  
pp. 174-178
Author(s):  
Jiao Qu ◽  
Shi Rong Ge
Keyword(s):  
Friction Coefficient ◽  
Friction Force ◽  
Self Assembly ◽  
Sliding Friction ◽  
Rolling Friction ◽  
Polystyrene Sphere ◽  
Si Substrate ◽  
Friction Behavior ◽  
Layer Film ◽  
Colloidal Spheres

The uniform sub-micron colloidal spheres were arrayed on the surface of a Si substrate via self-assembly to forming a sphere-layer film (monolayer), with emphasis on the application of rolling friction in the presence of rolling spheres on the surface of micro- or nano-equipment. It was found that the arrayed spheres on the substrate are mobile arising from rolling, and they can significantly reduce the friction force through changing the sliding friction to rolling one, thus exhibiting a smaller friction coefficient value than that of pure substrate. On the other hand, the elastic deformation of polystyrene (PS) spheres also contributes to the reduced friction force. In the absence of lubricant, the optimal friction coefficient of sphere-layer film was found to be 0.059 at the load of 3500 µN, at which the friction force of sphere-layer film was only 68% that of substrate. The friction coefficient of sphere-layer film decreases with increasing the applied load up to 3500 µN, followed by an increase with a further enhanced load, which has been ascribed to the transition from elastic contact to plastic one.

scholarly journals Identification of the Effect of Ultrasonic Friction Reduction in Metal-Elastomer Contacts Using a Two-Control-Loop Tribometer

2021 ◽  
Vol 11 (14) ◽  
pp. 6289
Author(s):  
Michael Weinstein ◽  
Christian Nowroth ◽  
Jens Twiefel ◽  
Jörg Wallaschek
Keyword(s):  
Friction Force ◽  
Force Control ◽  
Sliding Friction ◽  
Dynamic Contact ◽  
Friction Reduction ◽  
Ultrasonic Frequency ◽  
Stick Slip ◽  
Friction Forces ◽  
Variable Position ◽  
Sealing Ring

Pneumatic cylinders are widely used in highly dynamic processes, such as handling and conveying tasks. They must work both reliably and accurately. The positioning accuracy suffers from the stick-slip effect due to strong adhesive forces during the seal contact and the associated high breakaway forces. To achieve smooth motion of the piston rod and increased position accuracy despite highly variable position dynamics, sliding friction and breakaway force must be reduced. This contribution presents a specially designed linear tribometer that has two types of control. Velocity control allows the investigation of sliding friction mechanisms. Friction force control allows investigation of the breakaway force. Due to its bearing type, the nearly disturbance-free detection of stick-slip transients and the dynamic contact behavior of the sliding friction force was possible. The reduction of the friction force was achieved by a superposition of the piston rod’s movement by longitudinal ultrasonic vibrations. This led to significant reductions in friction forces at the rubber/metal interface. In addition, the effects of ultrasonic frequency and vibration amplitude on the friction reduction were investigated. With regard to the breakaway force, significant success was achieved by the excitation. The force control made it possible to identify the characteristic movement of the sealing ring during a breakaway process.

scholarly journals Effect of relaxation-dependent adhesion on pre-sliding response of cartilage

2018 ◽  
Vol 5 (5) ◽  
pp. 172051 ◽  
Author(s):  
Guebum Han ◽  
Melih Eriten
Keyword(s):  
Relaxation Time ◽  
Articular Cartilage ◽  
Sliding Friction ◽  
Relaxation Times ◽  
Shear Wave Elastography ◽  
Mechanistic Explanation ◽  
Propagation Rate ◽  
Work Of Adhesion ◽  
Adhesive Properties ◽  
Stick Slip

Possible links between adhesive properties and the pre-sliding (static) friction response of cartilage are not fully understood in the literature. The aims of this study are to investigate the relation between adhesion and relaxation time in articular cartilage, and the effect of relaxation-dependent adhesion on the pre-sliding response of cartilage. Adhesion tests were performed to evaluate the work of adhesion of cartilage at different relaxation times. Friction tests were conducted to identify the pre-sliding friction response of cartilage at relaxation times corresponding to adhesion tests. The pre-sliding friction response of cartilage was systematically linked to the work of adhesion and contact conditions by a slip-based failure model. It was found that the work of adhesion increases with relaxation time. Also, the work of adhesion is linearly correlated to the resistance to slip-based failure. In addition, as the work of adhesion increases, the adhered (stick) area at the moment of failure increases, and the propagation rate of the annular slip (crack) area towards its centre increases. These findings offer a mechanistic explanation of the pre-sliding friction behaviour and stick–slip response of soft hydrated interfaces such as articular cartilage and hydrogels. In addition, the linear correlation between adhesion and threshold to slip-based failure enables estimation of the adhesive strength of such interfaces directly from the pre-sliding friction response (e.g. shear wave elastography).

Friction Force and Stresses Analysis for Contact of Assembled Details

2006 ◽  
Vol 113 ◽  
pp. 334-338
Author(s):  
Z. Dreija ◽  
O. Liniņš ◽  
Fr. Sudnieks ◽  
N. Mozga
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Plastic Deformation ◽  
Friction Force ◽  
Sliding Friction ◽  
Friction Model ◽  
Contact Interface ◽  
Finite Element Program ◽  
Elastic Plastic ◽  
Element Program

The present work deals with the computation of surface stresses and deformation in the presence of friction. The evaluation of the elastic-plastic contact is analyzed revealing three distinct stages that range from fully elastic through elastic-plastic to fully plastic contact interface. Several factors of sliding friction model are discussed: surface roughness, mechanical properties and contact load and areas that have strong effect on the friction force. The critical interference that marks the transition from elastic to elastic- plastic and plastic deformation is found out and its connection with plasticity index. A finite element program for determination contact analysis of the assembled details and due to details of deformation that arose a normal and tangencial stress is used.

The Brake Device Design for Children Two-Wheel Dynamic Scooter

2011 ◽  
Vol 421 ◽  
pp. 724-727
Author(s):  
Xue Feng Yi ◽  
Li Jun He
Keyword(s):  
Sliding Friction ◽  
Rolling Friction ◽  
Safety Performance ◽  
Device Design ◽  
Emergency Braking ◽  
Design For Children ◽  
Brake Device

Children scooter safety performance is not good enough in the market, the cause of the majority of injuries to children is difficult to control the speed or emergency braking. According to the phenomenon, this paper focuses on designing dynamic scooter brake device for 8-10 child, we conceive that the brake device is given the force of the rolling friction and the sliding friction, so it can play a dual brake effect. It will enhance the security and stability of children dynamic scooter.

Frictional Behavior of Textile Fabrics Part I: Sliding Phenomena of Fabrics on Metallic and Polymeric Solid Surfaces

1997 ◽  
Vol 67 (11) ◽  
pp. 793-802 ◽  
Author(s):  
Luis Virto ◽  
Arun Naik
Keyword(s):  
Sliding Friction ◽  
Solid Material ◽  
Solid Surfaces ◽  
Friction Behavior ◽  
Stick Slip ◽  
Compression Load ◽  
Physical Description ◽  
Frictional Behavior ◽  
Textile Fabrics ◽  
Polymeric Solid

This paper presents experimental results on the sliding of fabrics on metallic and polymeric solid surfaces, showing the influence of the compression load at the solid-fabric interface and the nature of the solid material, and the effect of sliding speed on the sliding friction coefficient. At the same time, a physical description of the sliding phenomenon is given. On the basis of these observations, a theoretical approach is developed to explain the sliding friction behavior of fabrics on solid surfaces. Part II will deal with the waving and stick-slip phenomena, which are evident in the sliding process under certain conditions.

scholarly journals Calculation and AFM Experimental Research on Slip Friction for Unlubricated Spherical Contact with Roughness Effect

Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1428
Author(s):  
Shengguang Zhu ◽  
Liyong Ni
Keyword(s):  
Friction Force ◽  
Sliding Friction ◽  
Static Friction ◽  
Friction Model ◽  
Rigid Sphere ◽  
Roughness Effect ◽  
Force Microscopy ◽  
Comparison Results ◽  
Experimental Values ◽  
Calculation Models

Previous research on friction calculation models has mainly focused on static friction, whereas sliding friction calculation models are rarely reported. In this paper, a novel sliding friction model for realizing a dry spherical flat contact with a roughness effect at the micro/nano scale is proposed. This model yields the sliding friction by the change in the periodic substrate potential, adopts the basic assumptions of the Greenwood–Williamson random contact model about asperities, and assumes that the contact area between a rigid sphere and a nominal rough flat satisfies the condition of interfacial friction. It subsequently employs a statistical method to determine the total sliding friction force, and finally, the feasibility of this model presented is verified by atomic force microscopy friction experiments. The comparison results show that the deviations of the sliding friction force and coefficient between the theoretical calculated values and the experimental values are in a relatively acceptable range for the samples with a small plasticity index (Ψ ≤ 1).

Collision of two coins on a horizontal surface

2021 ◽  
Vol 57 (1) ◽  
pp. 015009
Author(s):  
Rod Cross
Keyword(s):  
Friction Force ◽  
Sliding Friction ◽  
Static Friction ◽  
Video Camera ◽  
Horizontal Surface ◽  
Collision Process ◽  
Oblique Angle ◽  
Billiard Ball ◽  
Air Table

Abstract Oblique angle collisions of two penny coins on a smooth, horizontal surface were filmed with a video camera to investigate the physics of the collision process. If one of the coins is initially at rest, then the two coins emerge approximately at right angles, as commonly observed in billiard ball collisions and in puck collisions on an air table. The coins actually emerged at an angle less than 90 degrees due to friction between the coins, which also resulted in both coins rotating after the collision. At glancing angles, the friction force was due to sliding friction. At other angles of incidence the coins gripped each other and the friction force was then due to static friction.

Sign in / Sign up

Export Citation Format

Share Document