Estimation of a Reduced Model of the BSM1 Activated Sludge Wastewater Treatment Plant

2008 ◽  
Vol 6 (1) ◽  
Author(s):  
Ouadiaa Barrou ◽  
Asma Karama ◽  
E. K. Lakhal ◽  
Olivier Bernard ◽  
Marie-Noelle Pons ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Kinetic Model ◽  
Activated Sludge ◽  
Treatment Plant ◽  
Reaction Scheme ◽  
Reduced Model ◽  
Biological Models ◽  
Output Data ◽  
State Observers ◽  
Data Representative

The complete BSM1 model is recognized as representative of activated sludge plants. However, its large number of states may render it inadequate for development of state observers and for control. Thus, a reduced model has been developed for the two main sections of the plant, the anoxic and aerobic reactors. Concepts of model reduction of biological models based on the analysis developed by Bernard (Bernard2005a, Bernard2005b) have been used. The output data have been obtained by simulating the inlet by data representative of dry weather. After transformation and treatment of the data, it has been shown that a kinetic model reduced to two reactions is able to represent 80% of the total variance. The pseudo-stoichiometric coefficients have been estimated and the pseudo reaction scheme has been validated with respect to the actual concentrations at the outlet of a considered section. The dynamics are generally well represented by the reduced model.

A model of the redox measurement in aerated activated sludge

2006 ◽  
Vol 53 (4-5) ◽  
pp. 465-472
Author(s):  
D. Cecil ◽  
E. Skou
Keyword(s):  
Wastewater Treatment ◽  
Kinetic Model ◽  
Activated Sludge ◽  
Oxygen Concentration ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Practical Interest ◽  
Metal Electrode ◽  
Organic Load ◽  
Ultimate Objective

A number of investigations have shown that pH, oxygen concentration, and the organic load affect the measured redox potential in aerated activated sludge. In this investigation, a model of the redox measurement is proposed. It is a kinetic model based on the necessary balance between the number of electrons accepted by and donated to a metal electrode in the sludge. The potential changes in order to maintain this balance. The model variables are pH, oxygen concentration, temperature and the activity of reduced compounds. Data from a wastewater treatment plant is analyzed using this model and it is shown that the model can be fitted to results from other published investigations. However we cannot as yet demonstrate a correlation between the activity of reduced compounds and the organic load on the sludge. The ultimate objective of this work is to extract more information from the redox measurement. This is a practical interest because the redox measurement is inexpensive and requires little maintenance.

DESIGN PLANNING WASTEWATER TREATMENT PLANT OF NATA DE COCO INDUSTRY WITH THE ACTIVATED SLUDGE PROCESS

2016 ◽  
Vol 9 (2) ◽  
Author(s):  
Dinda Rita K. Hartaja ◽  
Imam Setiadi
Keyword(s):  
Waste Water ◽  
Wastewater Treatment ◽  
Activated Sludge ◽  
Waste Water Treatment ◽  
Treatment Plant ◽  
Water Treatment Plant ◽  
Appropriate Technology ◽  
Waste Water Treatment Plant ◽  
Activated Sludge Process ◽  
High Level

Generally, wastewater of nata de coco industry contains suspended solids and COD were high, ranging from 90,000 mg / l. The high level of of the wastewater pollutants, resulting in nata de coco industry can not be directly disposed of its wastewater into the environment agency. Appropriate technology required in order to process the waste water so that the treated water can meet the environmental quality standards that are allowed. Designing the waste water treatment plant that is suitable and efficient for treating industrial wastewater nata de coco is the activated sludge process. Wastewater treatment using activated sludge process of conventional (standard) generally consists of initial sedimentation, aeration and final sedimentation.Keywords : Activated Sludge, Design, IPAL

Rehabilitation and Upgrading of the Beni Suef City Wastewater Treatment Plant

1990 ◽  
Vol 22 (7-8) ◽  
pp. 131-138
Author(s):  
Ahmed Fadel
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Primary Treatment ◽  
High Rate ◽  
Shock Load ◽  
Economic Evaluations ◽  
Activated Sludge Process ◽  
Trickling Filter

Many of Egypt's cities have existing treatment plants under operation that have been constructed before 1970. Almost all of these treatment plants now need rehabilitation and upgrading to extend their services for a longer period. One of these plants is the Beni Suef City Wastewater Treatment Plant. The Beni Suef WWTP was constructed in 1956. It has primary treatment followed by secondary treatment employing intermediate rate trickling filters. The BOD, COD, and SS concentration levels are relatively high. They are approximately 800, 1100, and 600 mg/litre, respectively. The Beni Suef city required the determination of the level of work needed for the rehabilitation and upgrading of the existing 200 l/s plant and to extend its capacity to 440 l/s at year 2000 A description of the existing units, their deficiencies and operation problems, and the required rehabilitation are presented and discussed in this paper. Major problems facing the upgrading were the lack of space for expansion and the shortage of funds. It was, therefore, necessary to study several alternative solutions and methods of treatment. The choice of alternatives was from one of the following schemes: a) changing the filter medium, its mode of operation and increasing the number of units, b) changing the trickling filter to high rate and combining it with the activated sludge process, for operation by one of several possible combinations such as: trickling filter-solids contact, roughing filter-activated sludge, and trickling filter-activated sludge process, c) dividing the flow into two parts, the first part to be treated using the existing system and the second part to be treated by activated sludge process, and d) expanding the existing system by increasing the numbers of the different process units. The selection of the alternative was based on technical, operational and economic evaluations. The different alternatives were compared on the basis of system costs, shock load handling, treatment plant operation and predicted effluent quality. The flow schemes for the alternatives are presented. The methodology of selecting the best alternative is discussed. From the study it was concluded that the first alternative is the most reliable from the point of view of costs, handling shock load, and operation.

Operational Results of the Wolfsburg Wastewater Treatment Plant

1992 ◽  
Vol 25 (4-5) ◽  
pp. 203-209 ◽  
Author(s):  
R. Kayser ◽  
G. Stobbe ◽  
M. Werner
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Nitrogen Content ◽  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Phosphate Removal ◽  
Total Nitrogen Content ◽  
Activated Sludge Process

At Wolfsburg for a load of 100,000 p.e., the step-feed activated sludge process for nitrogen removal is successfully in operation. Due to the high denitrification potential (BOD:TKN = 5:1) the effluent total nitrogen content can be kept below 10 mg l−1 N; furthermore by some enhanced biological phosphate removal about 80% phosphorus may be removed without any chemicals.

Management of toxicity effects in a large wastewater treatment plant

1997 ◽  
Vol 36 (2-3) ◽  
pp. 1-8 ◽  
Author(s):  
P. Grau ◽  
B. P. Da-Rin
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Severe Case ◽  
Treatment Efficiency ◽  
Filamentous Bulking ◽  
Biological Phenomena ◽  
Inhibition Of Nitrification ◽  
Toxicity Effects

An unusually severe case of toxicity accompanied by activated sludge filamentous bulking was observed at the wastewater treatment plant Sao Paulo-Barueri. Treatment efficiency of the plant, operated without major problems for more than five years before, was significantly hindered for almost six months. Occurrence of toxic shocks was confirmed partly directly but mostly indirectly by inhibition of nitrification and biological phenomena related to toxicity. Several measures adopted, including the recycled activated sludge chlorination, are described in the paper.

Automatic control for DO and pH in the activated sludge process in a coke wastewater treatment plant

1998 ◽  
Vol 37 (12) ◽  
pp. 141-148 ◽  
Author(s):  
B. K. Lee ◽  
S. W. Sung ◽  
H. D. Chun ◽  
J. K. Koo
Keyword(s):  
Wastewater Treatment ◽  
Control System ◽  
Activated Sludge ◽  
Automatic Control ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Pi Controller ◽  
Activated Sludge Process ◽  
Set Point ◽  
Coke Wastewater

The objective of this study is to develop an automatic control system for dissolved oxygen (DO) and pH of the activated sludge process in a coke wastewater treatment plant. A discrete type autotuned proportional-integral (PI) controller using an auto-regressive exogenous (ARX) model as a process model was developed to maintain the DO concentration in aerators by controlling the speed of surface aerators. Also a nonlinear pH controller using the titration curve was used to control the pH of influent wastewater. This control system was tested in a pilot scale plant. During this pilot plant experiment, there was small deviation of pH and the electric power consumption of surface aerators was reduced up to 70% with respect to the full operation when the DO set point was 2 mg/l. For real plant operation with this system, the discrete PI controller showed good tracking for set point change. The electricity saving was more than 40% of the electricity consumption when considering surface aerators. As a result of maintaining the DO constantly at the set point by the automatic control system, the fluctuation of effluent quality was decreased and overall improvement of the effluent water quality was achieved.

Savings with upgraded performance through improved activated sludge denitrification in the combined activated sludge–biofilter system of the Southpest Wastewater Treatment Plant

2008 ◽  
Vol 57 (8) ◽  
pp. 1287-1293 ◽  
Author(s):  
A. Jobbágy ◽  
G. M. Tardy ◽  
Gy. Palkó ◽  
A. Benáková ◽  
O. Krhutková ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Biological Treatment ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Process Efficiency ◽  
Initial Value ◽  
Initial Profile ◽  
Biological Treatment System

The purpose of the experiments was to increase the rate of activated sludge denitrification in the combined biological treatment system of the Southpest Wastewater Treatment Plant in order to gain savings in cost and energy and improve process efficiency. Initial profile measurements revealed excess denitrification capacity of the preclarified wastewater. As a consequence, flow of nitrification filter effluent recirculated to the anoxic activated sludge basins was increased from 23,000 m3 d−1 to 42,288 m3 d−1 at an average preclarified influent flow of 64,843 m3 d−1, Both simulation studies and microbiological investigations suggested that activated sludge nitrification, achieved despite the low SRT (2–3 days), was initiated by the backseeding from the nitrification filters and facilitated by the decreased oxygen demand of the influent organics used for denitrification. With the improved activated sludge denitrification, methanol demand could be decreased to about half of the initial value. With the increased efficiency of the activated sludge pre-denitrification, plant effluent COD levels decreased from 40–70 mg l−1 to < 30–45 mg l−1 due to the decreased likelihood of methanol overdosing in the denitrification filter

Evaluating the treatment performance of a full scale Activated Sludge Plant in Islamabad, Pakistan

2012 ◽  
Vol 7 (1) ◽  
Author(s):  
S. S. Fatima ◽  
S. Jamal Khan
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Suspended Solids ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Full Scale ◽  
Operational Parameter ◽  
Mixed Liquor ◽  
Treatment Performance

In this study, the performance of wastewater treatment plant located at sector I-9 Islamabad, Pakistan, was evaluated. This full scale domestic wastewater treatment plant is based on conventional activated sludge process. The parameters which were monitored regularly included total suspended solids (TSS), mixed liquor suspended solids (MLSS), mixed liquor volatile suspended solids (MLVSS), biological oxygen demand (BOD), and chemical oxygen demand (COD). It was found that the biological degradation efficiency of the plant was below the desired levels in terms of COD and BOD. Also the plant operators were not maintaining consistent sludge retention time (SRT). Abrupt discharge of MLSS through the Surplus Activated sludge (SAS) pump was the main reason for the low MLSS in the aeration tank and consequently low treatment performance. In this study the SRT was optimized based on desired MLSS concentration between 3,000–3,500 mg/L and required performance in terms of BOD, COD and TSS. This study revealed that SRT is a very important operational parameter and its knowledge and correct implementation by the plant operators should be mandatory.

Enhancing nitrogen removal efficiency in a dyestuff wastewater treatment plant with the IFFAS process: the pilot-scale and full-scale studies

2017 ◽  
Vol 77 (1) ◽  
pp. 70-78 ◽  
Author(s):  
Yanjun Mao ◽  
Xie Quan ◽  
Huimin Zhao ◽  
Yaobin Zhang ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Full Scale ◽  
Nitrification And Denitrification ◽  
Dyestuff Wastewater

Abstract The activated sludge (AS) process is widely applied in dyestuff wastewater treatment plants (WWTPs); however, the nitrogen removal efficiency is relatively low and the effluent does not meet the indirect discharge standards before being discharged into the industrial park's WWTP. Hence it is necessary to upgrade the WWTP with more advanced technologies. Moving bed biofilm processes with suspended carriers in an aerobic tank are promising methods due to enhanced nitrification and denitrification. Herein, a pilot-scale integrated free-floating biofilm and activated sludge (IFFAS) process was employed to investigate the feasibility of enhancing nitrogen removal efficiency at different hydraulic retention times (HRTs). The results showed that the effluent chemical oxygen demand (COD), ammonium nitrate (NH4+-N) and total nitrogen (TN) concentrations of the IFFAS process were significantly lower than those of the AS process, and could meet the indirect discharge standards. PCR-DGGE and FISH results indicated that more nitrifiers and denitrifiers co-existed in the IFFAS system, promoting simultaneous nitrification and denitrification. Based on the pilot results, the IFFAS process was used to upgrade the full-scale AS process, and the effluent COD, NH4+-N and TN of the IFFAS process were 91–291 mg/L, 10.6–28.7 mg/L and 18.9–48.6 mg/L, stably meeting the indirect discharge standards and demonstrating the advantages of IFFAS in dyestuff wastewater treatment.

Sign in / Sign up

Export Citation Format

Share Document