scholarly journals SHEAR STRENGTH OF RC BEAMS WITHOUT STIRRUP USING HIGH-STRENGTH CONCRETE OF COMPRESSIVE STRENGTH RANGING TO 130MPa

2003 ◽  
pp. 75-91
Author(s):  
Motoyuki SUZUKI ◽  
Mitsuyoshi AKIYAMA ◽  
Wei Lun WANG ◽  
Masayoshi SATO ◽  
Naomi MAEDA ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Rc Beams ◽  
Strength Concrete

Sensitivity of shear strength to fracture energy of high-strength concrete slabs

1998 ◽  
Vol 25 (1) ◽  
pp. 40-50 ◽  
Author(s):  
H Marzouk ◽  
M Emam ◽  
M S Hilal
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
High Strength Concrete ◽  
Shear Failure ◽  
High Strength ◽  
Tensile Fracture ◽  
Concrete Slabs ◽  
Square Root ◽  
Fracture Properties ◽  
Strength Concrete

The test results of an earlier experimental investigation conducted at Memorial University of Newfoundland on high-strength concrete slabs indicated that as the concrete slab strength increased from 35 to 75 MPa the shear strength increased by 7-20%, depending on the case of loading, i.e., concentric or eccentric loads. The increasing ratio of shear strength is less than half that prescribed in the Canadian code CSA-A23.3 (1994) or the ACI-318 code (1995). Hence, the significant difference between the experimental results and the predicted strength by existing North American codes tacitly means that the proportionality between the shear strength and the square root of the compressive strength is not accurate enough to predict the shear strength of high-strength concrete slabs. In the present investigation, a fracture mechanics model suitable for concrete was proposed. It was also suggested that this model might be an advantageous aid in the analysis of the shear failure of reinforced concrete slabs. In this research investigation the fracture mechanics approach utilizing finite element aided computer analysis of several reinforced slabs is briefly described, and calculated shear failure loads are given. The recommended model proves that it is necessary to consider not only the tensile strength of concrete, instead of the square root of the compressive strength, but also the tensile fracture properties of high-strength concrete. The tensile fracture properties of concrete are characterized by the parameter called characteristic length and the brittleness of concrete. The brittleness ratio of concrete slabs must be considered in any rational shear design expression to reflect the size effect factor and the aggregate type.Key words: fracture energy, uniaxial direct tension, shear strength, high-strength concrete, punching shear, slab, size effect, finite element analysis.

Shear design off high strength concrete beams — Canadian code perspective

1996 ◽  
Vol 23 (4) ◽  
pp. 809-819 ◽  
Author(s):  
Maria Anna Polak ◽  
Jaroslaw J. Dubas
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
High Strength Concrete ◽  
Concrete Beams ◽  
High Strength ◽  
Shear Behaviour ◽  
Shear Reinforcement ◽  
Concrete Compressive Strength ◽  
Strength Concrete ◽  
Shear Design

The paper presents the results of an investigation of the influence of concrete compressive strength on the shear strength of reinforced concrete beams, both nonprestressed and prestressed. A total of 132 existing tests on high strength concrete beams, with and without shear reinforcement, were analyzed and compared with the shear design provisions of the CSA Standard CAN3-A23.3-M94 and the previous version of the code, CAN3-A23.3-M84. The main parameter in the investigation was the concrete compressive strength. Owing to the complex nature of shear behaviour and the interdependence of the factors affecting shear strength, other parameters such as the shear span to depth ratio, the longitudinal reinforcement ratio, and the amount of shear reinforcement were varied, as well as the concrete strength. Key words: shear, beams, high strength concrete, code methods, shear reinforcement index, shear ratio, predictions, strength.

Effects of Nano-CaCO3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

2011 ◽  
Vol 121-126 ◽  
pp. 126-131 ◽  
Author(s):  
Qing Lei Xu ◽  
Tao Meng ◽  
Miao Zhou Huang
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Strength Concrete ◽  
Calcium Nitrite ◽  
Orientation Index ◽  
Early Strength

In this paper, effects of nano-CaCO3 on compressive strength and Microstructure of high strength concrete in standard curing temperature(21±1°C) and low curing temperature(6.5±1°C) was studied. In order to improve the early strength of the concrete in low temperature, the early strength agent calcium nitrite was added into. Test results indicated that 0.5% dosage of nano-CaCO3 could inhibit the effect of calcium nitrite as early strength agent, but 1% and 2% dosage of nano-CaCO3 could improve the strength of the concrete by 13% and 18% in standard curing temperature and by 17% and 14% in low curing temperature at the age of 3days. According to the XRD spectrum, with the dosage up to 1% to 2%, nano-CaCO3 can change the orientation index significantly, leading to the improvement of strength of concrete both in standard curing temperature and low curing temperature.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

Influence of Nano Particles in the Flexural Behavior of High-Strength Reinforced Concrete Beams

2021 ◽  
Vol 1160 ◽  
pp. 25-43
Author(s):  
Naglaa Glal-Eldin Fahmy ◽  
Rasha El-Mashery ◽  
Rabiee Ali Sadeek ◽  
L.M. Abd El-Hafaz
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Reinforced Concrete Beams ◽  
Nano Particles ◽  
Flexural Behavior ◽  
Single Type ◽  
Strength Concrete ◽  
Flexural Ductility

High strength concrete (HSC) characterized by high compressive strength but lower ductility compared to normal strength concrete. This low ductility limits the benefit of using HSC in building safe structures. Nanomaterials have gained increased attention because of their improvement of mechanical properties of concrete. In this paper we present an experimental study of the flexural behavior of reinforced beams composed of high-strength concrete and nanomaterials. Eight simply supported rectangular beams were fabricated with identical geometries and reinforcements, and then tested under two third-point loads. The study investigated the concrete compressive strength (50 and 75 N/mm2) as a function of the type of nanomaterial (nanosilica, nanotitanium and nanosilica/nanotitanium hybrid) and the nanomaterial concentration (0%, 0.5% and 1.0%). The experimental results showed that nano particles can be very effective in improving compressive and tensile strength of HSC, nanotitanium is more effective than nanosilica in compressive strength. Also, binary usage of hybrid mixture (nanosilica + nanotitanium) had a remarkable improvement appearing in compressive and tensile strength than using the same percentage of single type of nanomaterials used separately. The reduction in flexural ductility due to the use of higher strength concrete can be compensated by adding nanomaterials. The percentage of concentration, concrete grade and the type of nanomaterials, could predominantly affect the flexural behavior of HSRC beams.

Sign in / Sign up

Export Citation Format

Share Document