scholarly journals Prediction of Plunging Depth Induced by Top Lance Gas Blowing onto a Low-melting-point Metal Bath

2020 ◽  
Vol 60 (8) ◽  
pp. 1675-1683
Author(s):  
Shingo Sato ◽  
Makoto Ando ◽  
Jun Okada ◽  
Yoshiaki Ueda ◽  
Manabu Iguchi
Keyword(s):  
2019 ◽  
Vol 105 (1) ◽  
pp. 10-19 ◽  
Author(s):  
Shingo Sato ◽  
Makoto Ando ◽  
Jun Okada ◽  
Yoshiaki Ueda ◽  
Manabu Iguchi
Keyword(s):  

2013 ◽  
Vol 702 ◽  
pp. 62-67
Author(s):  
Jan Jezierski ◽  
Krzysztof Janerka

The paper presents the results of model experiments with new lance design. The lance was invented in Silesian University of Technology, Department of Foundry. It is dedicated for the pneumatic powder injection into liquid metal bath without lance submersion. The situation like that is common for small molten alloy volume when the problem of temperature decrease is significant. In such case the carrier gas introduction into metal as well as cooling with gas blowing onto metal bath surface should be avoided. The new lance was equipped with four parallel slots made on its outlet and a flange. This design causes the carrier gas evacuation before it reaches the molten metal surface. The article presents the model experiments made with use of the device for the diphase gas-powder jet forces recording. The comparison of two lances: normal steel pipe and this of new design was presented in the article, too.


Author(s):  
Robert C. Rau ◽  
Robert L. Ladd

Recent studies have shown the presence of voids in several face-centered cubic metals after neutron irradiation at elevated temperatures. These voids were found when the irradiation temperature was above 0.3 Tm where Tm is the absolute melting point, and were ascribed to the agglomeration of lattice vacancies resulting from fast neutron generated displacement cascades. The present paper reports the existence of similar voids in the body-centered cubic metals tungsten and molybdenum.


Author(s):  
William Krakow

It has long been known that defects such as stacking faults and voids can be quenched from various alloyed metals heated to near their melting point. Today it is common practice to irradiate samples with various ionic species of rare gases which also form voids containing solidified phases of the same atomic species, e.g. ref. 3. Equivalently, electron irradiation has been used to produce damage events, e.g. ref. 4. Generally all of the above mentioned studies have relied on diffraction contrast to observe the defects produced down to a dimension of perhaps 10 to 20Å. Also all these studies have used ions or electrons which exceeded the damage threshold for knockon events. In the case of higher resolution studies the present author has identified vacancy and interstitial type chain defects in ion irradiated Si and was able to identify both di-interstitial and di-vacancy chains running through the foil.


2000 ◽  
Vol 10 (PR7) ◽  
pp. Pr7-99-Pr7-102 ◽  
Author(s):  
G. Dosseh ◽  
D. Morineau ◽  
C. Alba-Simionesco
Keyword(s):  

1987 ◽  
Vol 48 (C1) ◽  
pp. C1-495-C1-501 ◽  
Author(s):  
Y. FURUKAWA ◽  
M. YAMAMOTO ◽  
T. KURODA

1963 ◽  
Vol 44 (1) ◽  
pp. 47-66 ◽  
Author(s):  
W. Nocke ◽  
H. Breuer

ABSTRACT A method for the chemical determination of 16-epi-oestriol in the urine of nonpregnant women with a qualitative sensitivity of less than 0.5 μg/24 h is described. The separation of 16-epi-oestriol and oestriol is accomplished by converting 16-epi-oestriol into its acetonide, a reaction which is stereoselective for cis-glycols and therefore not undergone by oestriol as a trans-glycol. Following partition between chloroform and aqueous alkali, the acetonide of 16-epi-oestriol is completely separated with the organic layer whereas oestriol as a strong phenol remains in the alkaline phase. 16-epi-oestriol is chromatographed on alumina as the acetonide and determined as a Kober chromogen. This procedure can easily be incorporated into the method of Brown et al. (1957 b) thus making possible the simultaneous routine assay of oestradiol-17β, oestrone, oestriol and 16-epi-oestriol from one sample of urine. The specificity of the method was established by separation of 16-epi-oestriol from nonpregnancy urine as the acetonide, hydrolysis of the acetonide by phosphoric acid, isolation of the free compound by microsublimation and identification by micro melting point, colour reactions and chromatography. The accuracy of the method is given by a mean recovery of 64% for pure crystalline 16-epi-oestriol when added to hydrolysed urine in 5–10 μg amounts. The precision is given by s = 0.24 μg/24 h. For the duplicate determination of 16-epi-oestriol the qualitative sensitivity is 0.44 μg/24 h, the maximum percentage error being ± 100% The quantitative sensitivity (±25% error) is 1.7 μg/24 h.


2015 ◽  
Vol 10 (1) ◽  
pp. 2641-2648
Author(s):  
Rizk Mostafa Shalaby ◽  
Mohamed Munther ◽  
Abu-Bakr Al-Bidawi ◽  
Mustafa Kamal

The greatest advantage of Sn-Zn eutectic is its low melting point (198 oC) which is close to the melting point. of Sn-Pb eutectic solder (183 oC), as well as its low price per mass unit compared with Sn-Ag and Sn-Ag-Cu solders. In this paper, the effect of 0.0, 1.0, 2.0, 3.0, 4.0, and 5.0 wt. % Al as ternary additions on melting temperature, microstructure, microhardness and mechanical properties of the Sn-9Zn lead-free solders were investigated. It is shown that the alloying additions of Al at 4 wt. % to the Sn-Zn binary system lead to lower of the melting point to 195.72 ˚C.  From x-ray diffraction analysis, an aluminium phase, designated α-Al is detected for 4 and 5 wt. % Al compositions. The formation of an aluminium phase causes a pronounced increase in the electrical resistivity and microhardness. The ternary Sn-9Zn-2 wt.%Al exhibits micro hardness superior to Sn-9Zn binary alloy. The better Vickers hardness and melting points of the ternary alloy is attributed to solid solution effect, grain size refinement and precipitation of Al and Zn in the Sn matrix.  The Sn-9%Zn-4%Al alloy is a lead-free solder designed for possible drop-in replacement of Pb-Sn solders.  


Sign in / Sign up

Export Citation Format

Share Document