Radiation performance of a cavity receiver for a parabolic dish solar concentrator system

2016 ◽  
pp. 488-493
Author(s):  
O. López ◽  
A. Arenas ◽  
A. Baños
Keyword(s):  
Solar Concentrator ◽  
Parabolic Dish

Design and Fabrication of Gamma-Type Stirling Engine on Parabolic Dish of Solar Concentrator by a Compression Ratio Method

2016 ◽  
Vol 851 ◽  
pp. 383-388 ◽  
Author(s):  
Khanuengchat Saenyot ◽  
Kitsakorn Locharoenrat ◽  
Sarai Lekchaum
Keyword(s):  
Compression Ratio ◽  
Solar Collector ◽  
Total Pressure ◽  
Weather Conditions ◽  
Stirling Engine ◽  
Ratio Method ◽  
Solar Concentrator ◽  
External Work ◽  
Parabolic Dish ◽  
Solar Tracker

In this article, we have designed and fabricated the gamma-type Stirling engine based on the compression ratio technique. This engine is attached on a parabolic dish of a solar collector. The engine shows a good performance in terms of compression ratio, external work, total pressure, and engine’s speed. Our engine offers the thermal efficiency of 30.59 % so that it can reach the output mechanical power of 0.934. The temperature difference of 137 K can maintain very well for the heat collection of the solar collector even when the weather conditions are poor. Furthermore, our materials are environmentally friendly and this design is expected to be in the applications of the solar tracker in the future.

scholarly journals Ray Tracing Study of Optical Characteristics of the Solar Image in the Receiver for a Thermal Solar Parabolic Dish Collector

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Saša R. Pavlovic ◽  
Velimir P. Stefanovic
Keyword(s):  
Ray Tracing ◽  
Low Cost ◽  
Optical Design ◽  
Solar Concentrator ◽  
Solar Collectors ◽  
Focal Distance ◽  
Medium Temperature ◽  
Parabolic Dish ◽  
Parabolic Dish Concentrator ◽  
Temperature Levels

This study presents the geometric aspects of the focal image for a solar parabolic concentrator (SPC) using the ray tracing technique to establish parameters that allow the designation of the most suitable geometry for coupling the SPC to absorber-receiver. The efficient conversion of solar radiation into heat at these temperature levels requires a use of concentrating solar collectors. In this paper detailed optical design of the solar parabolic dish concentrator is presented. The system has diameter D=3800 mm and focal distance f=2260 mm. The parabolic dish of the solar system consists of 11 curvilinear trapezoidal reflective petals. For the construction of the solar collectors, mild steel-sheet and square pipe were used as the shell support for the reflecting surfaces. This paper presents optical simulations of the parabolic solar concentrator unit using the ray tracing software TracePro. The total flux on the receiver and the distribution of irradiance for absorbing flux on center and periphery receiver are given. The goal of this paper is to present the optical design of a low-tech solar concentrator that can be used as a potentially low cost tool for laboratory scale research on the medium-temperature thermal processes, cooling, industrial processes, polygeneration systems, and so forth.

scholarly journals The Effect of Different Absorber Configurations On The Exergy and The Energy of Parabolic Solar Dish

2020 ◽  
Vol 7 (3) ◽  
pp. 1-13
Author(s):  
A'laa Taghi Al-Azawi ◽  
Ali A. F. Al Hamadani
Keyword(s):  
Heat Transfer ◽  
Heat Loss ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Tracking System ◽  
Open Cavity ◽  
Solar Concentrator ◽  
International Conference ◽  
National University ◽  
Parabolic Dish

Abstract— The solar energy is the most important type of energy. The parabolic dish solar collector (PDSC) is the best type among other solar collectors because it is always tracking the sun movement. The exergy and the energy performances of a PDS were analyzed experimentally and numerically. The effect of different coil geometries and different mass flow rates of heat transfer fluid (HTF) were investigated. The PDS has parabolic dish and receiver with diameter (1.5) m and (0.2) m respectively. Concentration ratio is 56.25. The parabolic polar dish was supported by a tracking system with two axes. The types of the copper absorber were used which are: (spiral –helical) coil (SHC) and spiral-conical coil (SCC). The results showed that the useful energy and thermal efficiency are varying with solar radiation variation. The useful energy varying between (480-765) W for (SHC), the thermal efficiency varying between (35.2-39.8) % for (SHC). Exergy efficiency varying between (6.9 –8.6) %. It was shown that the higher values of useful energy for (spiral – helical) absorber was 0.1L/min flow rate. REFERENCES  1. T. Taumoefolau , K. Lovegrove ," An Experimental Study of Natural Convection Heat Loss from a Solar Concentrator Cavity Receiver at Varying Orientation. ", Australian National University,, Canberra ACT 0200 AUSTRALIA.2002  2. S. PAITOONSURIKARN and K. LOVEGROVE," On the Study of Convection Loss from Open Cavity Receivers in Solar Paraboloidal Dish Applications ", Australian National University Canberra ACT 0200, AUSTRALIA, pp 154,155,2003  3. Soteris A. Kalogirou*,"Solar thermal collectors and applications", Higher Technical Institute, Progress in Energy and Combustion Science 30 (2004) 231–295, pp237, 240, 241, 2004  4. M. Prakash, S.B. Kedare, J.K. Nayak," Investigations on heat losses from a solar cavity receiver", Department of Energy Science and Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India,2008.  5. Shiva Gorjian1, Barat Ghobadian1, Teymour Tavakkoli Hashjin1, and Ahmad Banak ,"Thermal performance of a Point-focus Solar Steam Generating System ", 21st Annual International Conference on Mechanical Engineering-ISME201 7-9 May, 2013, School of Mechanical Eng., K.N.Toosi University, Tehran, Iran ,1ISME2013-1195,2013  6. Kailash Karunakaran1 Hyacinth J Kennady2 ,"Thermal Analysis of Parabolic Dish Snow Melting Device " ,International Journal for Research in Technological Studies| Vol. 1, Issue 3, February 2014 | ISSN (online): 2348-1439,2014  7. Charles-Alexis Asselineau, Ehsan Abbasi, John Pye "Open cavity receiver geometry influence on radiative losses" Australian National University (ANU), Canberra, ACT 0200 Australia. Solar2014: The 52nd Annual Conference of the Australian Solar Council 2014  8. Vahid Madadi, Touraj Tavakoli and Amir Rahimi First and second thermodynamic law analyses applied to a solar dish collector" DOI 10.1515/jnet-2014-0023 | J. Non-Equilib. Thermodyn. 2014; 39 (4):183–197  9. Yaseen. H. Mahmood , Mayadah K h. Ghaffar " Design of Solar dish concentration by using MATLAB program and Calculation of geometrical concentration parameters and heat transfer" , University of Tikrit , Tikrit , Iraq, Tikrit Journal of Pure Science 20 (4) ISSN: 1813 – 1662, 2015.  10. Vanita Thakkar, Ankush Doshi, Akshaykumar Rana "Performance Analysis Methodology for Parabolic Dish Solar Concentrators for Process Heating Using Thermic Fluid IOSR", Journal of Mechanical and Civil Engineering (IOSR-JMCE) eISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 1 Ver. II (Jan- Feb. 2015), PP 101-114  11. Saša R. pavlovi, Evangelos A. bellos, Velimir P. Stefanovi, Christos Tzivanidis and Zoran M. Stamenkovi "Design, Simulation ,and Optimiztion Of A Solar Dish Collector with spiral coil absorber ", , Nis, Serbia, thermal SCIENCE, Vol. 20, No. 4, pp. 1387-1397 1387,2016  12. Flávia V. Barbosa, João L. Afonso, Filipe B. Rodrigues, and José C. F. Teixeir," Development of a solar concentrator with tracking system", University of Minho,Guimarães, 4800-058, Portugal2016  13. O. López, A. Arenas, and A. Baños"Convective Heat Loss Analysis of a Cavity Receiver for a Solar Concentrator" International Conference on Renewable Energies and Power Quality (ICREPQ’17)Malaga (Spain), 4th to 6th April, 2017 ,ISSN 2172-038 X, No.15 April 2017 RE&PQJ, Vol.1, No.15, April 2017  14. D.R.Rajendran,E.GanapathySundaram,P.Jawahar "Experimental Studies on the Thermal Performance of a Parabolic Dish Solar Receiver with the Heat Transfer Fluids Sic water Nano Fluid and Water", Journal of Thermal Science Vol.26,  15. Muhammad Shoaib, Muhammad , Jameel Kabbir Ali ,Muhammad Usman1, Abdul Hannan " Analysis of thermal performance of parabolic dish collectors having different reflective" ,NFC institute of engineering &fertilizer research ,2018 .  16. Sasa PAVLOVIC, Evangelos BELLOS, Velimir STEFANOVIC ,Christos TZIVANIDIS " EXPERIMENTAL AND NUMERICAL INVESTIGATION OF A SOLAR DISH COLLECTOR WITH SPIRAL ABSORBER" A CTA TECHNICA CORVINIENSIS – Bulletin of Engineering Tome XI [2018] .   

Optical analysis and optimization of parabolic dish solar concentrator with a cavity receiver

Solar Energy ◽  
2013 ◽  
Vol 92 ◽  
pp. 288-297 ◽  
Author(s):  
Huairui Li ◽  
Weidong Huang ◽  
Farong Huang ◽  
Peng Hu ◽  
Zeshao Chen
Keyword(s):  
Solar Concentrator ◽  
Optical Analysis ◽  
Parabolic Dish

Analysis and Design of Two Stretched-Membrane Parabolic Dish Concentrators

1991 ◽  
Vol 113 (3) ◽  
pp. 180-187 ◽  
Author(s):  
Thomas R. Mancini
Keyword(s):  
State Of The Art ◽  
Focal Length ◽  
Production Costs ◽  
Single Element ◽  
Solar Concentrator ◽  
Optical Efficiency ◽  
Solar Concentrators ◽  
Analysis And Design ◽  
Parabolic Dish ◽  
Glass Metal

The state-of-the-art of parabolic dish solar concentrators is the faceted, glass-metal dish. The mass production costs of glass-metal dishes may be high because they do not incorporate the innovations of design and materials developed over the last eight years. Therefore, Sandia National Laboratories has undertaken to develop two stretched-membrane parabolic dish concentrators for the Department of Energy’s Solar Thermal Program. These solar concentrators are being designed for integration with an advanced solar receiver and a Stirling engine/generator in a 25-kWe power production unit. The first dish, which builds on the successful design of the stretched-membrane heliostats, is to be a low risk, near-term commercial solar concentrator. This solar concentrator comprises 12 large, 3.6-m diameter, stretched-membrane facets that are formed into parabolic shapes either with a large vacuum or by performing the thin membranes plastically. The focal length-to-diameter ratios (f/Ds) for the facets are about 3.0, relatively large for a dish but much lower than heliostats where they typically range from 50 to 100. Two contractors are currently fabricating facets for this dish, and a third contractor is designing the facet support structure and pedestal for the dish. The second stretched-membrane concentrator is a single-element monolithic dish with an f/D of 0.6. The dish is shaped into a parabola by plastically yielding the membrane using a combination of uniform and nonuniform loading. Initial measurements of the dish indicate that it has a slope error of 2.6 milliradians (one standard deviation) relative to a perfect parabola. In this paper, the designs of the two stretched-membrane dishes are analyzed using the computer code CIRCE to model the optical performance of the concentrators and a thermal model, which includes conduction, convection, and radiation heat transfer, to calculate the thermal losses from the cavity solar receivers. The solar collector efficiency, defined as the product of the optical efficiency of the collector and the thermal efficiency of the receiver, is optimized for comparing the performance of several solar concentrator configurations. Ten facet arrangements for the faceted stretched-membrane dish and the single-element stretched-membrane dish are modeled and their performances compared with that of a state-of-the-art glass-metal dish. Last, the initial designs of these two stretched-membrane dishes are described along with the results of preliminary performance measurements on their respective optical elements.

scholarly journals Effect of non-uniform temperature distribution on surface absorption receiver in parabolic dish solar concentrator

2017 ◽  
Vol 21 (5) ◽  
pp. 2011-2019 ◽  
Author(s):  
Ramalingam Senthil ◽  
Marimuthu Cheralathan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Mild Steel ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Heat Transfer Fluid ◽  
Solar Concentrator ◽  
Surface Absorption ◽  
Heat Gain ◽  
Parabolic Dish

A flat surface absorption receiver was experimentally investigated with a parabolic dish solar concentrator in order to study the effect of receiver temperature distribution on heat gain and losses. The addition of specially designed metal fins in the inner surface of the receiver surface side the receiver transfers the incident heat flux to heat transfer fluid. The receiver surface temperature increased with increase in concentration ratio, intensity of beam radiation, and ambient temperature, but decrease with wind speed. The absorptivity of black coated mild steel of 0.85 and also the 0.15 emissivity of mild steel reduced the heat loss from the surface and improved heat gain to heat transfer fluid. The temperature gradient between the receiver periphery and centre is around 150?C. Fluid flow direction like straight and curved paths have been discussed for effective heat absorption and reduced operational duration. The thermal efficiency and operational duration were determined for a flow rate of 80 litres per hour through the receiver. Water flow though the curved path was observed with improved thermal efficiency of 3.8% and 20% reduction in operational duration when compared to the vertical flow through the receiver at same flow rate.

Dual-sensitized upconversion-assisted, triple-band absorbing luminescent solar concentrators

Nanoscale ◽  
2020 ◽  
Vol 12 (33) ◽  
pp. 17265-17271
Author(s):  
Seong Kyung Nam ◽  
Kiwon Kim ◽  
Ji-Hwan Kang ◽  
Jun Hyuk Moon
Keyword(s):  
Solar Light ◽  
Photovoltaic Systems ◽  
Solar Concentrator ◽  
Solar Concentrators ◽  
Luminescent Solar Concentrators ◽  
Luminescent Solar Concentrator ◽  
Triple Band

Luminescent solar concentrator-photovoltaic systems (LSC-PV) harvest solar light by using transparent photoluminescent plates, which is expected to be particularly useful for building-integrated PV applications.

Sign in / Sign up

Export Citation Format

Share Document