APPLICATION OF MICROFILTRATION AND ULTRAFILTRATION FOR REUSING TREATED WASTEWATER; AS A SOLUTION TO EASE IRAN’S WATER SHORTAGE PROBLEMS

2015 ◽  
Vol 11 (6) ◽  
pp. 3662-3668
Author(s):  
Leila Babaei ◽  
A. Torabian ◽  
B. Aminzadeh
Keyword(s):  
Removal Efficiency ◽  
Membrane Filtration ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Water Shortage ◽  
Fecal Coliforms ◽  
Treated Wastewater ◽  
Secondary Effluent ◽  
Allowable Level ◽  
Ozone Injection

Water shortage is a big problem in the Middle East. This paper investigates the possibility of reusing municipal wastewater by membrane filtration for non-potable consumption. The wastewater used for tests in this study was secondary effluent discharged from the secondary sedimentation pond of Ekbatan wastewater treatment plant in Tehran. These tests on reusing wastewater involved four main processes. Results showed that the best process was that ozone injection before MF and UF with COD removal efficiency of approximately 78 percent. In this case, removal efficiency of turbidity and TSS were 100 percent; additionally, traces of total and fecal Coliforms were completely removed. In the membrane processes, removal efficiency of TKN was about 40 percent. The removal efficiency of TP in all processes was about 7 percent, while it increased to 14 percent in the hybrid treatment. It can be concluded that all of further purification processes failed to achieve total phosphorus (TP) standards and thus in order to eliminate TP and reach allowable level, further researches are needed.<w:LsdException Locked="false" Priority="73" SemiHidden="false" UnhideWhenUsed="false" Name="Color

scholarly journals Efficiency of municipal wastewater treatment with membrane bioreactor

2019 ◽  
Vol 41 (1) ◽  
pp. 47-54
Author(s):  
Magdalena Domańska ◽  
Anna Boral ◽  
Kamila Hamal ◽  
Magdalena Kuśnierz ◽  
Janusz Łomotowski ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Membrane Filtration ◽  
Municipal Wastewater ◽  
High Efficiency ◽  
Biological Membrane ◽  
Treatment Plant ◽  
Membrane Reactors ◽  
Quality Analysis ◽  
Treated Wastewater ◽  
Municipal Wastewater Treatment

AbstractThe increasingly stringent requirements for wastewater treatment enforce the adoption of technologies that reduce pollution and minimize waste production. By combining the typical activated sludge process with membrane filtration, biological membrane reactors (MBR) offer great technological potential in this respect. The paper presents the principles and effectiveness of using an MBR at the Głogów Małopolski operation. Physicochemical tests of raw and treated wastewater as well as microscopic analyses with the use of the FISH (fluorescence in situ hybridization) method were carried out. Moreover, the level of electric energy consumption during the operation of the wastewater treatment plant and problems related to fouling were also discussed. A wastewater quality analysis confirmed the high efficiency of removing organic impurities (on average 96% in case of BOD5 and 94% in case of COD) and suspension (on average 93%).

scholarly journals Application of SAC254 measurement for the assessment of micropollutant removal in the adsorptive treatment stage of a municipal wastewater treatment plant

2016 ◽  
Vol 11 (2) ◽  
pp. 503-515 ◽  
Author(s):  
Annette Rößler ◽  
Steffen Metzger
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Wastewater Treatment Plant ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Treated Wastewater ◽  
Municipal Wastewater Treatment ◽  
Adsorptive Treatment ◽  
Micropollutant Removal ◽  
Treatment Stage

In 2010, the Mannheim wastewater treatment plant was expanded with an adsorptive treatment stage to remove organic micropollutants (OMPs). Differences in the removal efficiencies of the OMPs investigated were determined over four years of operation by applying different powdered activated carbon (PAC) products and a constant volume-proportional dosing of 10 mg PAC/L. Possible influences on the removal efficiency are discussed here on the basis of the data obtained, exemplified for the analgesic diclofenac. The analyses show that the removal efficiency is influenced significantly by the spectral absorption coefficient (SAC) of the biologically treated wastewater at a wavelength of 254 nm (SAC254). Therefore, in order to ensure the constant treatment performance desired, the dosage of PAC should be adjusted to the measured SAC254 values. Moreover, as the SAC254 reduction correlates with the removal efficiency of OMPs, the additional determination of its reduction allows indirect control of the actual removal performance achieved. The SAC254 reduction can also be used for targeted control of the PAC dosage.

Anaerobic Biofiltration versus Aerobic Membrane Filtration: Comparison on a Difficult Substrate

1992 ◽  
Vol 25 (10) ◽  
pp. 211-218 ◽  
Author(s):  
P. Sauvegrain ◽  
A. Tazi-Pain ◽  
F. Rogalla ◽  
F. Valter
Keyword(s):  
Removal Efficiency ◽  
Membrane Filtration ◽  
Suspended Solids ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Municipal Wastewater Treatment ◽  
Loading Rates ◽  
Anaerobic Filter ◽  
Aerobic Reactor ◽  
Membrane Treatment

Several methods were compared to treat heat treatment liquor on a municipal wastewater treatment plant, to reduce loading and allow upgrading. To ensure low suspended solids in the return flows, granular anaerobic filters were chosen in parallel with membrane treatment:–an upflow wood-based charcoal anaerobic filter–an upflow floating polystyrene anaerobic filter–an aerobic reactor (activated sludge) coupled with microfiltration. Very similar loading rates and removal efficiency was obtained with the anaerobic filters; they allow to treat highly concentrated effluents in a detention time of 10 h but COD removal efficiency was limited to 60%. The higher contact time of up to 7 days in aerobic treatment, coupled with microfiltration, achieves elimination of 85% of COD and 95% of BOD. Nevertheless, loading rates and biomass concentrations remained low and flux on the membranes was heavily restricted.

WASTEWATER DISINFECTION BY UV AT TRANI MUNICIPAL PLANT

1994 ◽  
Vol 30 (4) ◽  
pp. 125-132 ◽  
Author(s):  
D. Carnimeo ◽  
E. Contini ◽  
R. Di Marino ◽  
F. Donadio ◽  
L. Liberti ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Continuous Operation ◽  
Secondary Effluent ◽  
Municipal Wastewater Treatment ◽  
South Italy ◽  
Wastewater Disinfection ◽  
Pilot Investigation ◽  
Effluent Characteristics

The pilot investigation on the use of UV as an alternative disinfectant to NaOCI was started in 1992 at Trani (South Italy) municipal wastewater treatment plant (335 m3/h). The results collected after six months continuous operation enabled us to compare UV and NaOCl disinfection effectiveness on the basis of secondary effluent characteristics, quantify photoreactivation effects, evidence possible DBP formation and assess costs.

Enhanced Performance of Ultrafiltration Membrane with Powdered Zeolite Addition for Secondary Effluent Treatment

2013 ◽  
Vol 838-841 ◽  
pp. 2712-2716
Author(s):  
Yong Tu ◽  
Yong Gang Bai ◽  
Yong Chen ◽  
Wei Jing Liu ◽  
Jun Xu ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Fluorescence Spectra ◽  
Municipal Wastewater ◽  
Three Dimensional ◽  
Treatment Plant ◽  
Ultrafiltration Membrane ◽  
Effluent Treatment ◽  
Secondary Effluent ◽  
Municipal Wastewater Treatment ◽  
Sem Images

The research on ultrafiltration membrane assisted by powdered zeolite for the treatment of secondary effluent from a municipal wastewater treatment plant was studied. The results show that membrane fouling rate is reduced by pre-coating the ultrafiltration membrane with powdered zeolite, and the treatment performance of secondary effluent is enhanced. UV-vis, three-dimensional excitation emission matrix (3D-EEM) fluorescence spectra and scanning electron microscopy (SEM) images for ultrafiltration were also discussed.

scholarly journals Electrochemical redox treatment of denitrification in coastal secondary effluent using Ti/IrO2 anode

2021 ◽  
Author(s):  
Yaozong Zhang ◽  
Bo Pang
Keyword(s):  
Removal Efficiency ◽  
Treatment Plant ◽  
Chloride Ion ◽  
Ion Concentration ◽  
Secondary Effluent ◽  
Low Carbon ◽  
Cathodic Potential ◽  
Nitrate N ◽  
N Removal ◽  
Electrochemical Redox

Abstract In northern coastal industrial park, inlet of the wastewater treatment plant (WWTP) had the characteristics of low carbon source and high chloride ion concentration, which resulted in its poor biodegradability. In this case, the experiment explored an electrochemistral method to remove nitrogen. Cathodic potential, Ti/IrO2 was confirmed as the anode and − 1.6V was taken as the potential in order to remove nitrate-N. The findings include: when the initial chloride ion was 2000 and 3000 mg/L, the effect on the removal difference of nitrogen was slight. When the electrolysis time was 60 min, ammonia-N was removed completely, nitrite-N concentration kept 1mg/L approximately. The ammonia-N removal efficiency went up with the increasing cathodic potential, and was completely removed in different water samples, but nitrate-N removal showed an opposite result. The production amount of nitrite-N was the least at -1.6V. As the pH increased, ammonia-N and nitrate-N’s removal efficiency went up first and then down, the removal effect was the best at pH being 9, Nitrite-N was less influenced by pH. After optimizing the raw water sample, Nitrate-N and TN removal efficiency were significantly increased, but the nitrite-N almost kept constant.

scholarly journals Reuse of treated wastewater using sequencing batch bioreactor for the improvement of wheat growth

2011 ◽  
Vol 1 (3) ◽  
pp. 179-184 ◽  
Author(s):  
Beenish Saba ◽  
Tariq Mahmood ◽  
Bushra Zaman ◽  
Imran Hashmi
Keyword(s):  
Removal Efficiency ◽  
Growth Parameters ◽  
Wheat Variety ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Laboratory Scale ◽  
Treated Wastewater ◽  
Reclaimed Wastewater ◽  
Attached Growth ◽  
Batch Bioreactor

Reclaimed wastewater reuse for irrigation to crop plants is evaluated in a laboratory-scale experiment to assess growth and water saving potential from natural resources. A prototype laboratory-scale treatment plant was established for this purpose with suspended and attached growth configurations. Chakwal wheat variety was selected to examine growth parameters. The removal of chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) were evaluated to check the quality of treated water. It was found that a suspended growth sequencing batch bioreactor (SGSBBR) achieved 97% ± 2 removal efficiency over a 4 h hydraulic retention time (HRT). For an attached growth sequencing batch bioreactor (AGSBBR) results showed 98% ± 2 removal efficiencies with polyurethane. TN and TP removal efficiency was 58.7 ± 3% and 64 ± 4.8% in SGSBBR, 53 ± 0.17% and 67 ± 2.7% in polyurethane. AGSBBR enhanced performance with AGSBBR may be due to enforced anoxic/aerobic conditions in the inner layers of biofilm formed on biocarriers which facilitate the required metabolic conditions for treating high strength wastewater. Plant growth was visibly greater in SGSBBR treated wastewater than AGSBBR because of less nutrient removal.

scholarly journals Upflow packed bed Anammox reactor used in two-stage deammonification of sludge digester effluent

2018 ◽  
Vol 78 (9) ◽  
pp. 1843-1851 ◽  
Author(s):  
İ. Çelen-Erdem ◽  
E. S. Kurt ◽  
B. Bozçelik ◽  
B. Çallı
Keyword(s):  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Municipal Wastewater ◽  
Removal Rate ◽  
Treatment Plant ◽  
Packed Bed ◽  
Municipal Wastewater Treatment ◽  
Two Stage ◽  
N Removal ◽  
Total Nitrogen Removal

Abstract The sludge digester effluent taken from a full scale municipal wastewater treatment plant (WWTP) in Istanbul, Turkey, was successfully deammonified using a laboratory scale two-stage partial nitritation (PN)/Anammox (A) process and a maximum nitrogen removal rate of 1.02 kg N/m3/d was achieved. In the PN reactor, 56.8 ± 4% of the influent NH4-N was oxidized to NO2-N and the effluent nitrate concentration was kept below 1 mg/L with 0.5–0.7 mg/L of dissolved oxygen and pH of 7.12 ± 12 at 24 ± 4°C. The effluent of the PN reactor was fed to an upflow packed bed Anammox reactor where high removal efficiency was achieved with NO2-N:NH4-N and NO3-N:NH4-N ratios of 1.32 ± 0.19:1 and 0.22 ± 0.10:1, respectively. The results show that NH4-N removal efficiency up to 98.7 ± 2.4% and total nitrogen removal of 87.7 ± 6.5% were achieved.

scholarly journals Microplastics Removal from Treated Wastewater by a Biofilter

Water ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 1085 ◽  
Author(s):  
Fan Liu ◽  
Nadia Nord ◽  
Kai Bester ◽  
Jes Vollertsen
Keyword(s):  
Particle Number ◽  
Treatment Plant ◽  
Complete Removal ◽  
Pilot Scale ◽  
Particle Mass ◽  
Treated Wastewater ◽  
Secondary Effluent ◽  
Global Environmental Issue ◽  
Wwtp Effluent ◽  
Global Environmental

Microplastic (MP) pollution is a global environmental issue, and traditionally treated wastewater has been identified as a source of land-based microplastics into the aquatic environment. This study evaluated the performance of a pilot-scale biofilter to polish wastewater treatment plant (WWTP) effluent before it enters the environment. The filter was divided into four zones, allowing the concentration of microplastics to be followed through the filter. It was fed with secondary effluent from a conventional WWTP in Denmark. The raw effluent from the WWTP contained 917 items m−3 which corresponded to a mass concentration of 24.8 µg m−3. After the top layer of the biofilter, the concentration had decreased to a median value of 197 item m−3 and 2.8 µg m−3, indicating an overall removal efficiency of 79% in terms of particle number and 89% in terms of particle mass. We also observed a tendency that MP of larger size and higher particle mass were more likely to be retained. After the last filtration zone, all MP larger than 100 µm had been removed. The results of this study demonstrate that biofilters are able to lower the MP abundance in treated wastewater significantly, but a complete removal is not ensured, hence some MP, particularly small-sized ones, can still be discharged into the receiving environment.

Sign in / Sign up

Export Citation Format

Share Document