scholarly journals Combustion stability control of gasoline compression ignition (GCI) under low-load conditions: A review

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Leilei Liu ◽  
Zhifa Zhang ◽  
Yue Liang ◽  
Fan Zhang ◽  
Binbin Yang
Keyword(s):  
High Efficiency ◽  
Stability Control ◽  
Combustion Stability ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Low Load ◽  
Temperature Combustion ◽  
Future Work ◽  
Load Conditions

Abstract With greater energy pressure and stricter emission standards, increasing power output and reducing emissions of engines are simultaneously required. To achieve this, considerable researches are motivated. In recent years, key and representative developments in the field of high-efficiency and clean engines have been carried out. Among them, a low temperature combustion concept called gasoline compression ignition (GCI) is widely considered by universities and research institutions around the world, since it has the potential to achieve ultra-low NO X and soot emissions while maintaining high thermal efficiency. However, GCI combustion mode has certain issues to be solved, such as combustion instability under low-load conditions. Therefore, this paper reviews the experimental, computational and optical studies on the combustion stability control of GCI combustion mode during low loads and describes the recent progress to improve combustion stability as well as points out the future work finally.

Initial Results on a New Light-Duty 2.7L Opposed-Piston Gasoline Compression Ignition Multi-Cylinder Engine

2018 ◽  
Author(s):  
Ashwin Salvi ◽  
Reed Hanson ◽  
Rodrigo Zermeno ◽  
Gerhard Regner ◽  
Mark Sellnau ◽  
...  
Keyword(s):  
Pressure Rise ◽  
High Load ◽  
Combustion Stability ◽  
Residual Fraction ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Peak Cylinder Pressure ◽  
Low Load ◽  
Initial Results ◽  
Load Conditions

Gasoline compression ignition (GCI) is a cost-effective approach to achieving diesel-like efficiencies with low emissions. Traditional challenges with GCI arise at low-load conditions due to low charge temperatures causing combustion instability and at high-load conditions due to peak cylinder pressure and noise limitations. The fundamental architecture of the two-stroke Achates Power Opposed-Piston Engine (OP Engine) enables GCI by decoupling piston motion from cylinder scavenging, allowing for flexible and independent control of cylinder residual fraction and temperature leading to improved low load combustion. In addition, the high peak cylinder pressure and noise challenges at high-load operation are mitigated by the lower BMEP operation and faster heat release for the same pressure rise rate of the OP Engine. These advantages further solidify the performance benefits of the OP Engine and demonstrate the near-term feasibility of advanced combustion technologies, enabled by the opposed-piston architecture. This paper presents initial results from a steady state testing on a brand new 2.7L OP GCI multi-cylinder engine. A part of the recipe for successful GCI operation calls for high compression ratio, leading to higher combustion stability at low-loads, higher efficiencies, and lower cycle HC+NOx emissions. In addition, initial results on catalyst light-off mode with GCI are also presented. The OP Engine’s architectural advantages enable faster and earlier catalyst light-off while producing low emissions, which further improves cycle emissions and fuel consumption over conventional engines.

scholarly journals PRELIMINARY STUDY OF WATER INJECTION ON THE COMBUSTION AND EMISSIONS CHARACTERISTICS IN A HCCI ETHANOL ENGINE

2020 ◽  
Vol 19 (2) ◽  
pp. 50
Author(s):  
G. D. Telli ◽  
G. Y. Zulian ◽  
S. R. Stefanello ◽  
T. D. M. Lanzanova ◽  
M. E. S. Martins ◽  
...  
Keyword(s):  
Fossil Fuels ◽  
High Efficiency ◽  
Thermal State ◽  
Water Injection ◽  
Combustion Stability ◽  
Intake Manifold ◽  
Renewable Fuels ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Diesel Generator

Our dependence on fossil fuels coupled with concerns about harmful emissions have motivated researchers to look for renewable fuels that have clean combustion and for advanced combustion modes. In this context, homogeneous charge compression ignition (HCCI) is an emerging technology which offers an alternative to conventional spark ignition and compression ignition engines and can operate on renewable fuels. Low temperature combustion, which can result in low NOx emissions with high indicated efficiency, is the more important characteristic of this combustion mode. It’s main problem is the combustion timing control due to lack of direct ignition control, once HCCI flame initiation is based on charge thermal state. Thus, controlled auto-ignition (CAI) combustion mode has been proposed. Several methods were proposed for combustion phasing control, between them, the injection of water in the intake manifold. This work investigated the influence of water injection in the intake runner of an ethanol HCCI cylinder from a converted three-cylinder diesel generator set, in which two cylinders operated on conventional diesel combustion and one diesel cylinder provided recycled exhaust gas for the one cylinder running on ethanol HCCI combustion. The water injection was used to control the CA50 combustion parameter. The results show that water injection is an efficient strategy to control the combustion timing, since the reactivity of the mixture can be controlled. The results at 400 and 600 kPa of IMEP and 1800 rpm indicated a good combustion stability, high efficiency and low emissions characteristics. The highest indicated fuel conversion efficiency found was 36.9% for 600 kPa of IMEP and 8 CAD of CA50. However, for 200 kPa of IMEP the combustion was unstable, the indicated efficiency was deteriorated and indicted CO emissions was high.

Low Temperature Combustion Within an HSDI Diesel Engine Using Multiple Injection Strategies

2007 ◽  
Author(s):  
Tiegang Fang ◽  
Robert E. Coverdill ◽  
Chia-Fon F. Lee ◽  
Robert A. White
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Injection Pressure ◽  
High Load ◽  
Injection Timing ◽  
Diesel Combustion ◽  
Low Temperature Combustion ◽  
Combustion Mode ◽  
Temperature Combustion ◽  
Load Conditions

Low Temperature Compression Ignition (LTCI) combustion employing multiple injection strategies in an optical High-Speed Direct Injection (HSDI) diesel engine was investigated in this work. Heat release characteristics were analyzed through the measurement of in-cylinder pressure. The whole cycle combustion process was visualized with a high-speed digital video camera by imaging natural flame luminosity and three-dimensional-like combustion structures were obtained by taking flame images from both the bottom of the optical piston and the side window simultaneously. The NOx emissions were measured in the exhaust pipe. The effects of pilot injection timing, pilot fuel quantity, main injection timing, operating load, and injection pressure on the combustion and emissions were studied. Low temperature combustion mode was achieved by using a small pilot injection with an injection timing much earlier than TDC followed by a main injection after TDC. For comparison, experiment of a diffusion diesel combustion case was also conducted. Premixed-combustion-dominated heat release rate pattern was seen for all the low temperature combustion cases, while a typical diffusion flame combustion heat release rate was obtained for the conventional combustion case. Highly luminous flame was observed for the conventional combustion condition while much less luminous flame was seen for the low temperature combustion cases. For the higher load and lower injection pressure cases, liquid fuel being injected into low temperature premixed flame was observed for certain cases, which was different from the conventional diesel combustion with liquid fuel injected into hot premixed flame. Compared with the conventional diffusion diesel combustion, simultaneous reduction of soot and NOx was obtained for the low temperature combustion mode at both the same and increased injection pressure with similar operating load. For high load conditions, higher NOx emissions were obtained than the low load conditions with the same injection pressure due to a higher in-cylinder temperature under high load conditions with more fuel burned. However, compared with the diffusion combustion mode with a lower load at lower injection pressure, a significant reduction of soot was achieved for the high load conditions, which shows that increasing injection pressure greatly reduce soot emissions.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Sign in / Sign up

Export Citation Format

Share Document