Conducting polyaniline/multi-wall carbon nanotubes composite paints on low carbon steel for corrosion protection: electrochemical investigations

2013 ◽  
Vol 67 (8) ◽  
Author(s):  
Pravin Deshpande ◽  
Sanket Vathare ◽  
Shashikant Vagge ◽  
Elena Tomšík ◽  
Jaroslav Stejskal
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Steel ◽  
Corrosion Protection ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Low Carbon ◽  
Multi Wall Carbon Nanotubes ◽  
Poly Aniline

AbstractThe coaxial coating of multi-wall carbon nanotubes (MWCNT) with poly(aniline) (PANI) was synthesised and a paint was prepared containing conducting PANI-MWCNT composite. The corrosion protection performance was assessed by open circuit potential measurements, potentiodynamic polarisation, and electrochemical impedance spectroscopy. The corrosion rate of low-carbon steel coated with 1.5 mass % of PANI-MWCNT-based paint in 3.5 mass % sodium chloride solution was found to be 0.037 mm y−1, about 5.2 times lower than that of unpainted low-carbon steel and 3.6 times lower than that of epoxy painted steel.

Experimental study of the mechanical and corrosion properties of ethyl silicate resin applied on low carbon steel

2021 ◽  
Vol 2 (108) ◽  
pp. 68-74
Author(s):  
M. Ali ◽  
J.H. Mohmmed ◽  
A.A. Zainulabdeen
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Open Circuit Potential ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Treatment Temperature ◽  
Ethyl Silicate ◽  
Low Carbon ◽  
Corrosion Properties ◽  
Mixture Ratio

Purpose: This work aimed at evaluating the properties of the ethyl silicate-based coating that can be applied on low carbon steel. Design/methodology/approach: Two mixture ratio types (2:1, and 3:2) of resin and hardener respectively were used to prepared two specimen models (A and B). Findings: It found that some mechanical properties (tensile, hardness, and impact strength) of ethyl silicate resin were evaluated according to standard criteria. Research limitations/implications: The effect of heat treatments at various temperatures (100, 150, and 200°C) and holding at different times (10, 20 & 30) min on hardness was investigated. Practical implications: Moreover, an open circuit potential corrosion test with a solution of 3.5% Sodium Chloride at room temperature and 60°C was used to determine the corrosion resistance of low carbon steel specimens coated with the two mixture types. Originality/value: The effects of mixture ratios (for resin and hardener) and heat treatment conditions on properties of ethyl silicate-based coating were studied. From obtained results, acceptable values of tensile, hardness, and toughness were recorded. Increasing heat treatment temperature and holding time leads to enhance hardness for both model types. An open circuit potential (OCP) tests show that there is an enhancement of protective properties of ethyl silicate coatings with mixture type B in comparison with type A was achieved. Generally, the results indicate that specimen model B has higher properties as compared with specimen model A.

Corrosion study of low carbon steel under simulated geological disposal environments for HLW in China

2020 ◽  
Author(s):  
Junhua Dong
Keyword(s):  
Carbon Steel ◽  
Corrosion Rate ◽  
Dissolved Oxygen ◽  
Open Circuit Potential ◽  
Steel Substrate ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Low Carbon ◽  
Simulated Groundwater

<p>In the multi-barrier system of HLW repository, overpack is the first barrier to isolate high-level radioactive nuclides from biosphere, and Low carbon steel has been considered to be a promising candidate material for manufacturing the oberpack due to its good mechanical performance and workability and weldability. However, during thousands of years of geological disposal, the corrosion resistance of low carbon steel and its corrosion evolution behavior are the first element that must be fully understood, because it determines the life cycle of the artificial barrier.</p><p>Conventional studies had suggested that the corrosion of low carbon steel under the deep geological environment was driven by hydrogen evolution reaction (HER) based on that the dissolved oxygen was completely depleted during the long term disposal. However, the residual oxygen content is a critical factor to determine the corrosion mode of cathodic reduction reaction. Thermodynamics data indicated that the initial ferrous corrosion products formed in the deaerated bicarbonate solution can be chemically oxidized into ferric substance by the trace content of dissolved oxygen, and the accumulated FeOOH as a cathodic depolarizer significantly increased the open circuit potential and enhanced the corrosion rate of the low carbon steel. Moreover, chloride and sulfate in the simulated groundwater can reduce the increase of open circuit potential but it still promotes the corrosion of the low carbon steel. As the environments contained aggressive anions and high concentration of dissolved oxygen, low carbon steel was prone to suffer from the localized corrosion and the corrosion rate was obviously increased. By alloying with some contents of Ni and Cu, the corrosion rate of low alloy steel was decreased by an order of magnitude and it was less prone to suffer from the localized corrosion.</p><p>Under the conditions of simulated groundwater with different content of GMZ bentonite，the bentonite colloidal particle layer attached to the surface of low carbon steel showed blocking effect on resisting oxygen diffusion to the steel substrate, which consequently decrease the further oxidation of ferrous to ferric substances and the corrosion rate of low carbon steel. However, the barrier performance of bentonite colloids would be deteriorated due to their coagulation caused by the ferrous ions dissolved from the steel substrate. High content of bentonite was beneficial to maintain and to prolong the stabilization of the barrier system. An equivalent circuit model which correlates with the interfacial structure between electrode substrate and rust and bentonite layer was proposed. The fitting results showed a very good match between the model and experimental data, and the evolution of the results was also in agreement with real changes.</p>

scholarly journals Electrochemical studies of the synergistic combination effect of thymus mastichina and illicium verum essential oil extracts on the corrosion inhibition of low carbon steel in dilute acid solution

2020 ◽  
Vol 11 (1) ◽  
pp. 1-13
Author(s):  
Roland Tolulope Loto ◽  
Samuel Keme Ororo
Keyword(s):  
Weight Loss ◽  
Carbon Steel ◽  
Corrosion Inhibition ◽  
Open Circuit Potential ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Low Carbon ◽  
Inhibition Effect ◽  
Illicium Verum ◽  
Hcl Solution

AbstractInhibition effect of the synergistic combination of thymus mastichina and illicium verum oil extracts (TMAV) on the corrosion inhibition of low carbon steel in 0.5 M H2SO4 and HCl solution was studied by weight loss analysis, potentiodynamic polarization, open circuit potential measurement, ATF-FTIR spectroscopy, and optical microscopy and macroscopic characterization. Results from weight loss shows TMAV performed more effectively in H2SO4 solution compared to HCl with optimal inhibition efficiency of 81.24% and 68.33%. Effective inhibition performance was observed at all TMAV concentration in H2SO4 compared to HCl where TMAV performed poorly until 5% concentration. The optimal inhibition performances from potentiodynamic polarization are 80.85% and 70.43%. The corresponding corrosion current density and polarization resistance are 7.16 × 105 A/cm2 and 8.01 × 105 A/cm2, and 331.73 and 284 Ω. TMAV exhibited mixed type inhibition effect in both acid solutions, strongly influencing the anodic-cathodic plot configurations with respect to concentration. Open circuit potential plots without TMAV were significantly electronegative compared to the plots at 1% and 5% TMAV concentration which were relative electropositive due to decreased thermodynamic tendency of the carbon steel to corrode. The corresponding plots at 1% and 5% TMAV concentration from HCl solution were thermodynamically unstable with significant active-passive corrosion behaviour. TMAV inhibited through chemisorption adsorption according to Langmuir and Freudlich adsorption isotherms in H2SO4 solution, and Frumkin and Freundlich adsorption isotherms in HCl solution with correlation coefficient values between 0.7 and 0.9. FTIR spectroscopic analysis exposed the functional groups and atomic bonds responsible for corrosion inhibition.

Corrosion protection performance of nano-TiO2-containing phosphate coatings obtained by anodic electrochemical treatment

2019 ◽  
Vol 37 (6) ◽  
pp. 565-578 ◽  
Author(s):  
Vaibhav S. Kathavate ◽  
Nilesh S. Bagal ◽  
Pravin P. Deshpande
Keyword(s):  
Carbon Steel ◽  
Corrosion Protection ◽  
Zinc Phosphate ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Electrochemical Treatment ◽  
Phosphate Coating ◽  
Low Carbon ◽  
X Ray ◽  
Phosphate Coatings

AbstractThe efficacy of nano-TiO2-containing zinc phosphate coatings on low-carbon steel is investigated. Zinc phosphate coatings are electrodeposited on low-carbon steel (AISI 1015) keeping current density, deposition time and wt % nano-TiO2 at their respective levels. Corrosion protection performance of these coatings was assessed using potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl electrolyte. The morphology, the composition and the growth process of the zinc phosphate coating is investigated using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy, X-ray diffraction (XRD) and electrochemical measurements. The XRD study reveals that the obtained phosphate layer contains traces of hopeite and phosphophylite. The formed zinc phosphate coating offers high corrosion protection in 3.5% NaCl solution, which is well supported by EIS studies. The presence of nano-TiO2 in the phosphate bath anticipated to offer a better surface coverage and reduction in porosity and forms more homogeneous coating, which is in agreement with the SEM studies. The optimization of the electrodeposition phosphating process for achieving better responses in terms of corrosion rate and coating resistance is addressed in this paper.

Phenylcoumarin Glucoside as a Natural Inhibitor in the Protection of Low Carbon Steel Against Corrosion

MRS Advances ◽  
2017 ◽  
Vol 2 (62) ◽  
pp. 3909-3915
Author(s):  
Héctor M. Barbosa Cásarez ◽  
Araceli Espinoza Vázquez ◽  
Francisco J. Rodríguez-Gomez
Keyword(s):  
Carbon Steel ◽  
Inhibition Efficiency ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Low Carbon Steel ◽  
Steel Corrosion ◽  
Low Carbon ◽  
Low Concentrations ◽  
Natural Inhibitor ◽  
Polarization Studies

AbstractPhenylcoumarin glucoside (4-PC) is a compound extracted from the plant Hintona latiflora and was studied as inhibitor for AISI 1018 steel corrosion in 3% NaCl solution using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques, which may find application as eco-friendly corrosion inhibitors. The 4-PC provides inhibitor properties that protect AISI 1018 low carbon steel against corrosion at low concentrations (5 ppm) obtained by EIS. Polarization studies showed that the inhibitor was of mixed type. The inhibition efficiency by the two electrochemical techniques shows similar results. The inhibitor adsorption was demonstrated to be a combined process (physisorption and chemisorption) according to the Langmuir isotherm.

Corrosion Behavior of Al-Si-Cr-Cu Bearing Low Carbon Steel in A Cyclic Dry/Wet Laboratory Test

2009 ◽  
Vol 79-82 ◽  
pp. 1017-1020 ◽  
Author(s):  
Hui Shu Zhang ◽  
Dong Ping Zhan ◽  
Song Lian Bai ◽  
Zhou Hua Jiang
Keyword(s):  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Optical Microscope ◽  
Low Carbon ◽  
Rust Layer ◽  
Electrochemical Behaviors ◽  
Corrosion Rates ◽  
The Matrix ◽  
Corrosion Behaviors

The corrosion behaviors of Al-Si-Cr-Cu bearing low carbon steel and a reference steel Q235 were tested in a cyclic dry/wet environment containing 0.01mol/L NaHSO3 in laboratory. Rust layers were observed by optical microscope (OM), scanning electron microscopy (SEM) and XRD. The electrochemical behaviors of the steels were studied on the polarization curves and electrochemical impedance spectroscopy (EIS). The results indicate that after 120h corrosion test, the annual corrosion rates of the designed steels reduce 42 % than Q235 at least. The corrosion products are generally iron oxyhydroxides and oxides such as FeOOH, γ-FeOOH, α-FeOOH, γ-Fe2O3, Fe3O4. The α-FeOOH possesses good stabilization mainly exits and can improve the corrosion resistance. There are the enrichments of Cu, Cr, Si and Al in the rust layer close to the matrix, which make the rust layer be more compact and protected. The corrosion currents of the two designed steels are lower than that of Q235, the corrosion potentials are higher than that of Q235 after Tafel fitting. The rust layer impedances of the designed steels are higher than that of Q235.

Effect of Nanoparticle Addition in Hybrid Sol-Gel Silane Coating on Corrosion Resistance of Low Carbon Steel

2013 ◽  
Vol 686 ◽  
pp. 244-249 ◽  
Author(s):  
Poovarasi Balan ◽  
Aaron Ng ◽  
Chee Beng Siang ◽  
R.K. Singh Raman ◽  
Eng Seng Chan
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Electrochemical Corrosion ◽  
Alumina Nanoparticles ◽  
Low Carbon ◽  
Silane Coating ◽  
Sol Gel Films

Chromium pre-treatments of metal have been replaced by silane pre-treatments as more environmental friendly option. Nanoparticles can be added in the silane sol-gel network have been reported to improve corrosion resistance. In this work, the electrochemical corrosion resistance of low carbon steel coated with hybrid organic-inorganic sol-gel film filled with nanoparticles was evaluated. The sol-gel films have been synthesized from 3-glycidoxy-propyl-trimethoxy-silane (3-GPTMS) and tetra-ethyl-ortho-silicate (TEOS) precursors. These films have been impregnated with 300 ppm of silica or alumina nanoparticles. The electrochemical behavior of the coated steel was evaluated by means of electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). Equivalent circuit modeling, used for quantifying the EIS measurements showed that sol-gel films containing silica nanoparticles improved the barrier properties of the silane coating. The silica nanoparticle-containing films showed highest initial pore resistance over the five days of immersion in 0.05M NaCl.

Sign in / Sign up

Export Citation Format

Share Document