scholarly journals Mechanical Properties of Magnesium Alloys Produced by Powder Metallurgy Method.

1996 ◽  
Vol 43 (11) ◽  
pp. 1350-1353 ◽  
Author(s):  
Hajime Iwasaki ◽  
Kisho Yanase ◽  
Takasuke Mori ◽  
Mamoru Mabuchi ◽  
Kenji Higashi
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Magnesium Alloys ◽  
Powder Metallurgy Method

Mixing Y89 Influence on Mechanical Properties of Casting Mg17Al12

2015 ◽  
Vol 667 ◽  
pp. 303-307
Author(s):  
Hang Song Yang ◽  
Shao Ju Hao ◽  
Jun Jie Liang
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Rare Earth ◽  
Powder Metallurgy ◽  
Magnesium Alloy ◽  
Light Quality ◽  
Mechanical Performance ◽  
Powder Metallurgy Method ◽  
Compression Performance ◽  
Refinement Effect

For its light quality, good thermal conductivity, and excellent electricity shielding performance, Magnesium alloy has been used in industry, agricultural and so on, for rare earth elements can improve the mechanical performance of magnesium alloy, the study of powder metallurgy is influence by rare earth magnesium is few at present. so, in this paper, by mixing powder metallurgy method the Y89 element was added in Mg17Al12 magnesium alloy, the influence of Y89 on microstructure, hardness and compression performance of Mg17Al12 magnesium alloy was studied, The experimental results show that when amount of Y89’s addition, the mechanical performance is more then and when is 1.22%, its mechanical performance is best, hardness is 66.7 HV, compressive strength is 113.6 MPa,increased respectively by 19.7% and 29.3% compared the Mg17Al12 magnesium alloy substrate, and the grain refinement effect of Mg17Al12 magnesium alloy is the best at this time.

Improvement in physical and mechanical properties of aluminum/zircon composites fabricated by powder metallurgy method

2011 ◽  
Vol 32 (8-9) ◽  
pp. 4417-4423 ◽  
Author(s):  
Hossein Abdizadeh ◽  
Maziar Ashuri ◽  
Pooyan Tavakoli Moghadam ◽  
Arshia Nouribahadory ◽  
Hamid Reza Baharvandi
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Physical And Mechanical Properties ◽  
Powder Metallurgy Method

Mechanical properties of Al-Cu/B4C and Al-Mg/B4C metal matrix composites

2021 ◽  
Vol 63 (4) ◽  
pp. 350-355
Author(s):  
Mehmet Ayvaz ◽  
Hakan Cetinel
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Liquid Phase ◽  
Oxide Layer ◽  
Solid Phase ◽  
Aluminum Matrix ◽  
Liquid Phase Sintering ◽  
Aluminum Matrix Composites ◽  
Powder Metallurgy Method ◽  
Matrix Composites

Abstract To be able to successfully produce ceramic-reinforced aluminum matrix composites by using the powder metallurgy method, the wetting of ceramic reinforcements should be increased. In addition, the negative effects of the oxide layer of the aluminum matrix on sinterability should be minimized. In order to break the oxide layer, the deoxidation property of Mg can be used. Furthermore, by creating a liquid phase, both wettability and sinterability can be improved. In this study, the effects of Mg and Cu alloy elements and sintering phase on the wettability, sinterability, and mechanical properties of Al/B4C composites were investigated. For this purpose, various amounts (5, 10, 20, and 30 wt.-%) of B4C reinforced Al5Cu and Al5Mg matrix composites were produced by the powder metallurgy method. After pressing under 400 MPa pressure, composite samples were sintered for 4 hours. The sintering was carried out in two different groups as solid phase sintering at 560 °C and liquid phase sintering at 610 °C. Despite the deoxidation effect of Mg in Al5Mg matrix composites, higher mechanical properties were determined in Al5Cu composites which were sintered in liquid phase because wettability increased. The highest mechanical properties were obtained in the 20 wt.-% B4C reinforced Al5Cu sample sintered in liquid phase.

Microstructural Evolution and Mechanical Properties of AZ91 and SiCp/AZ91 Magnesium Alloys upon Rapid Solidification/Powder Metallurgy Followed by Hot Extrusion

2010 ◽  
Vol 146-147 ◽  
pp. 734-737
Author(s):  
Hui Yu ◽  
Hua Shun Yu ◽  
Zhen Ya Zhang ◽  
Guang Hui Min ◽  
Cheng Chen
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Magnesium Alloys ◽  
Rapid Solidification ◽  
Microstructural Evolution ◽  
Hot Extrusion ◽  
Interface Debonding ◽  
Porosity Level ◽  
Az91 Magnesium ◽  
Sic Particulates

In this study, AZ91 and SiC particulates reinforced AZ91 (SiCp/AZ91) magnesium alloys were successfully fabricated using rapid solidification/powder metallurgy technique followed by hot extrusion. Microstructural evolution and mechanical properties of the monolithic AZ91 and SiCp/AZ91 magnesium alloys were evaluated. SiC particulates were well distributed with only few agglomerated particles. The porosity level and microhardness increased as SiCp content increased because the increased surface area of SiCp, harder ceramic phases and SiCp acted obstacles to the motion of dislocations. In addition, an increase in particulate reinforcement content was observed to decrease mechanical properties of the composite compared with the unreinforced counterpart due to increasing agglomerating regions and porosity, brittle interface debonding between matrix and SiCp.

Sign in / Sign up

Export Citation Format

Share Document