scholarly journals Behaviour of Uniaxial Reinforced Concrete Columns Strengthened with Ultra-High Performance Concrete and Fiber Reinforced Polymers

2021 ◽  
Vol 28 (2) ◽  
pp. 54-72
Author(s):  
Abd-al-Salam Al-Hazragi ◽  
Assim Lateef
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Columns ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced Polymers ◽  
Tension Zone ◽  
Fiber Reinforced ◽  
Group A ◽  
Group B

This article investigates the behaviour of strengthened concrete columns using jacketing ultra-high-performance fiber reinforced concrete (UHPFRC) and carbon fiber-reinforced polymer (CFRP) under uniaxial loaded. The jacket was connected to the column core using shear connectors and (CFRP) fixed as a strip on the tension zone between the column cores and the jacketing. Seven column samples of square cross-section (120 x120) mm at the midsection with overall length of 1250 mm were cast using normal strength concrete (NSC) and having similar longitudinal and transverse reinforcement. The samples were made and tested under axial load at eccentricity equal to 120 mm up to failure. Test parameters were the thickness of jackets (25 and 35) mm and the width of CFRP (0,8, and 12) cm. Column specimens were tested, one of them was reference without any strengthening, and the other specimens divided into two groups (A, and B), and each group included three specimens based on the parameters. Group (A) has UHPFRC jacket thickness 25 mm and CFRP width (0,8, and 12) cm respectively, and group (B) has UHPFRC jacket thickness 35 mm and CFRP width (0,8, and 12) cm respectively. The outcomes of the article show that increasing the thickness of jacket, and width of CFRP lead to increase in the load carrying capacity about (110.5%,168.4%, and 184.2%) for group A, and (157.9%,226.3%, and 263.2%) for group B compared with the reference column due to delay in the appearance of cracks and their distribution. The mid-height lateral displacement of columns was decreased about (66.6%,42.3%, and 35.9%) for group A, and (46.15%,38.46%, and 32.3%) for group B, also the axial deformation of specimens decreased about (71.7%,60.86%, and 55.86%) for group A, and (65.5%,60.5%, and 53.4) for group B compared with the reference column. The ductility of columns that were strengthened with UHPFRC jacket only was increased about (13.67%,19.66%) for thickness(25,35) mm respectively, because of that UHPFRC jacket was contented on steel fibers, and the percentage decrease of ductility was about (5.1%,and 12%) for group (A), (1%,and 9.4%) for group (B) when bonded CFRP in the tension zone with width (8 ,and 12) cm respectively. The results show improvement in the initial and secant stiffness when, increased the thickness of jacket, and width of CFRP because of increase in the size of columns and improvement in the modulus of elasticity. The toughness increase was about (273.97%,301.55%, and 304.5%) for group A, and (453.69%,511.93%, and 524.28%) for group B compared with the reference column because of increase in the size of specimens and delay the appearance of cracks.

Behaviour of Uniaxial Reinforced Concrete Columns Strengthened with Ultra-High Performance Concrete and Fiber Reinforced Polymers

2021 ◽  
Vol 28 (2) ◽  
pp. 54-72
Author(s):  
Abd-al-Salam Al-Hazragi ◽  
Assim Lateef
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Columns ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced Polymers ◽  
Tension Zone ◽  
Fiber Reinforced ◽  
Group A ◽  
Group B

This article investigates the behaviour of strengthened concrete columns using jacketing ultra-high-performance fiber reinforced concrete (UHPFRC) and carbon fiber-reinforced polymer (CFRP) under uniaxial loaded. The jacket was connected to the column core using shear connectors and (CFRP) fixed as a strip on the tension zone between the column cores and the jacketing. Seven column samples of square cross-section (120 x120) mm at the midsection with overall length of 1250 mm were cast using normal strength concrete (NSC) and having similar longitudinal and transverse reinforcement. The samples were made and tested under axial load at eccentricity equal to 120 mm up to failure. Test parameters were the thickness of jackets (25 and 35) mm and the width of CFRP (0,8, and 12) cm. Column specimens were tested, one of them was reference without any strengthening, and the other specimens divided into two groups (A, and B), and each group included three specimens based on the parameters. Group (A) has UHPFRC jacket thickness 25 mm and CFRP width (0,8, and 12) cm respectively, and group (B) has UHPFRC jacket thickness 35 mm and CFRP width (0,8, and 12) cm respectively. The outcomes of the article show that increasing the thickness of jacket, and width of CFRP lead to increase in the load carrying capacity about (110.5%,168.4%, and 184.2%) for group A, and (157.9%,226.3%, and 263.2%) for group B compared with the reference column due to delay in the appearance of cracks and their distribution. The mid-height lateral displacement of columns was decreased about (66.6%,42.3%, and 35.9%) for group A, and (46.15%,38.46%, and 32.3%) for group B, also the axial deformation of specimens decreased about (71.7%,60.86%, and 55.86%) for group A, and (65.5%,60.5%, and 53.4) for group B compared with the reference column. The ductility of columns that were strengthened with UHPFRC jacket only was increased about (13.67%,19.66%) for thickness(25,35) mm respectively, because of that UHPFRC jacket was contented on steel fibers, and the percentage decrease of ductility was about (5.1%,and 12%) for group (A), (1%,and 9.4%) for group (B) when bonded CFRP in the tension zone with width (8 ,and 12) cm respectively. The results show improvement in the initial and secant stiffness when, increased the thickness of jacket, and width of CFRP because of increase in the size of columns and improvement in the modulus of elasticity. The toughness increase was about (273.97%,301.55%, and 304.5%) for group A, and (453.69%,511.93%, and 524.28%) for group B compared with the reference column because of increase in the size of specimens and delay the appearance of cracks.

scholarly journals Resistance of an Optimized Ultra-High Performance Fiber Reinforced Concrete to Projectile Impact

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 63
Author(s):  
Anna L. Mina ◽  
Michael F. Petrou ◽  
Konstantinos G. Trezos
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Depth Of Penetration ◽  
Projectile Impact ◽  
High Performance Fiber

The scope of this paper is to investigate the performance of ultra-high performance fiber reinforced concrete (UHPFRC) concrete slabs, under projectile impact. Mixture performance under impact loading was examined using bullets with 7.62 mm diameter and initial velocity 800 m/s. The UHPFRC, used in this study, consists of a combination of steel fibers of two lengths: 6 mm and 13 mm with the same diameter of 0.16 mm. Six composition mixtures were tested, four UHPFRC, one ultra-high performance concrete (UHPC), without steel fibers, and high strength concrete (HSC). Slabs with thicknesses of 15, 30, 50, and 70 mm were produced and subjected to real shotgun fire in the field. Penetration depth, material volume loss, and crater diameter were measured and analyzed. The test results show that the mixture with a combination of 3% 6 mm and 3% of 13 mm length of steel fibers exhibited the best resistance to projectile impact and only the slabs with 15 mm thickness had perforation. Empirical models that predict the depth of penetration were compared with the experimental results. This material can be used as an overlay to buildings or to construct small precast structures.

scholarly journals Concrete columns confined with different composite materials

2018 ◽  
Vol 199 ◽  
pp. 09012 ◽  
Author(s):  
Jacopo Donnini ◽  
Valeria Corinaldesi
Keyword(s):  
Composite Materials ◽  
High Performance ◽  
Optimal Solution ◽  
Concrete Columns ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced Polymers ◽  
Vapor Permeability ◽  
Fiber Reinforced ◽  
Existing Structures ◽  
Low Performance

In the last decades, the need for upgrading, strengthening and retrofitting of existing concrete structures is rapidly growing. Composite materials showed to be an optimal solution to face this problem, combining high efficacy with low invasiveness. The use of Fiber Reinforced Polymers (FRP) to wrap concrete columns has been widely investigated and became a very successful method to improve their structural performances. However, it has been recognized that FRPs, due to the presence of an organic resin, have a few drawbacks, such as poor mechanical behavior at high temperatures, lack of vapor permeability and impossibility to be installed on wet surfaces. This experimental work aims to propose a comparison between three different innovative methods as possible strengthening solutions for existing concrete columns. The structural behavior of 20 reduced scale concrete columns, realized by using a low performance concrete, in order to reproduce the poor mechanical properties of existing structures, was investigated. Two unreinforced column were tested in compression as reference. Six of them where reinforced by applying an external layer of FRP, with different types of fabric reinforcement (made of carbon or PBO fibers). Six columns were reinforced by using the same fabrics coupled with an inorganic matrix (FRCM) instead of epoxy. Six other columns were reinforced by using a layer of High Performance Fiber Reinforced Concrete (HPFRC) of 3 cm thick. Experimental results have been analyzed and performance of the three reinforcement systems have been compared.

Influence of Different Mechanical Properties to the Concrete Penetration Resistance

2014 ◽  
Vol 982 ◽  
pp. 119-124 ◽  
Author(s):  
Tomáš Vavřiník ◽  
Jan Zatloukal
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
High Speed ◽  
High Performance ◽  
High Performance Concrete ◽  
Penetration Resistance ◽  
Fiber Reinforced Concrete ◽  
Experimental Program ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete

This paper describes influence of different mechanical properties to the concrete penetration resistance. The resistance is evaluated on the basis of the presented experimental program. In the experiment, non-deformable ogive-nose projectiles with diameter of 7.92 mm and mass of 8 g with impact velocity of about 700 m/s were hitting center of the specimens. Determination of the concrete penetration resistance was than based on projectile residual velocity obtained from high-speed camera record. The specimens were made from high strength concrete, steel fiber-reinforced concrete, ultra-high performance concrete and ultra-high performance fiber-reinforced concrete with different fiber content. The concrete penetration resistance was evaluated on total 32 specimens. Influence of mechanical properties, addition of coarse aggregate and steel fibers were discussed. Mechanical properties of the tested materials were investigated on total 125 specimens. Data from the measurements were used for creation of new RHT concrete models in Autodyn. In order to confirm experiment's setup and results, numerical analysis was performed in Autodyn. Results of the numerical simulations were compared to the experimental program.

Sign in / Sign up

Export Citation Format

Share Document