scholarly journals Structural State Effect on Mechanical Properties and Acoustic Emission of High-Purity Titanium at Different Types of Deformation

2019 ◽  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
High Purity ◽  
Acoustic Waves ◽  
Hydrostatic Extrusion ◽  
Dislocation Slip ◽  
Petch Relation ◽  
Strength Differential ◽  
Purity Titanium

The results on investigations of mechanical properties of high-purity titanium with grains ranging from tens of nanometers up to a few micrometers subjected to uniaxial tension, compression and microindenting are presented. Different structural states in high-purity titanium were formed by severe plastic deformation according to the scheme «upsetting – extrusion – drawing» in combination with annealing at temperatures of 250–550° C and quasi-hydrostatic extrusion at room and liquid nitrogen temperatures. The values of yield strengths and microhardness for samples of high-purity titanium with grains of different sizes are determined. It was shown that the combination of severe plastic deformation with cryogenic quasi-hydrostatic extrusion allowed to create high-purity nanocrystalline titanium with high mechanical properties. The obtained experimental data were analyzed for the implementation of the Hall-Petch relation and discrepancy between the values of yield strengths in tension and compression (strength differential or S-D effect). Satisfactory fulfillment of the Hall-Petch relation for high-purity titanium in the whole range of the studied grain size values was shown and a noticeable difference in the yield values for compression and tension was found. The values of the coefficients in the Hall-Petch equation for deformation by tension, compression and microindenting were determined. These coefficients are noticeably lower than the corresponding values for the industrial grades of titanium, i.e. in high-purity titanium, the grain boundaries are weaker barriers for moving dislocations than in the industrial titanium, whose boundaries are enriched with impurities. The features of the acoustic waves emission during compression of samples in various structural states were studied. It was concluded that the deformation of titanium in all the investigated structural states was carried out by dislocation slip.

Influence of Severe Plastic Deformation on the PLC Effect and Mechanical Properties in Al 5XXX Alloy

2006 ◽  
Vol 114 ◽  
pp. 171-176 ◽  
Author(s):  
Joanna Zdunek ◽  
Pawel Widlicki ◽  
Halina Garbacz ◽  
Jaroslaw Mizera ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
True Strain ◽  
Tensile Tests ◽  
Size Reduction ◽  
Hydrostatic Extrusion ◽  
Stress Strain ◽  
Chatelier Effect

In this work, Al-Mg-Mn-Si alloy (5483) in the as-received and severe plastically deformed states was used. Plastic deformation was carried out by hydrostatic extrusion, and three different true strain values were applied 1.4, 2.8 and 3.8. All specimens were subjected to tensile tests and microhardness measurements. The investigated material revealed an instability during plastic deformation in the form of serration on the stress-strain curves, the so called Portevin-Le Chatelier effect It was shown that grain size reduction effected the character of the instability.

scholarly journals INTENSE PLASTIC DEFORMATION OF HIGH-PURITY CAST BERYLLIUM

2020 ◽  
pp. 230-235
Author(s):  
A.A. Vasil’ev ◽  
S.P. Stetsenko ◽  
R.L. Vasilenko ◽  
D.G. Malykhin ◽  
P.I. Stoyev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Grain Refinement ◽  
High Purity ◽  
Recrystallization Annealing ◽  
Initial State ◽  
Angular Pressing ◽  
Temperature Dependences ◽  
First Time

Studies were made into the effect of severe plastic deformation on the mechanical properties, structure, and texture of high-purity cast beryllium. For the first time, angular pressing of high-purity cast beryllium was carried out at temperatures of 600 and 500 °C. It is shown that the degree of grain refinement during angular pressing into a strip reaches a significant value. In a single deformation cycle, the grain is crushed from 3 mm down to 10 μm. Temperature dependences of the mechanical properties of the material of extruded billets in the initial state and after recrystallization annealing at a temperature of 650 °C for one hour were studied. It has been established that the best mechanical properties are shown by the samples of material deformed at 600 °C with subsequent annealing at 650 °C for an hour.

The Influence of Hydrostatic Extrusion on the Microstructure of 6082 Aluminium Alloy

2006 ◽  
Vol 114 ◽  
pp. 145-150 ◽  
Author(s):  
Pawel Widlicki ◽  
Halina Garbacz ◽  
Małgorzata Lewandowska ◽  
Wacław Pachla ◽  
Mariusz Kulczyk ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Tensile Strength ◽  
Severe Plastic Deformation ◽  
Light Microscopy ◽  
Aluminium Alloy ◽  
Extrusion Process ◽  
Hydrostatic Extrusion ◽  
Fine Grained

Hydrostatic extrusion can be viewed as one of the methods of Severe Plastic Deformation, SPD, for the fabrication of ultra-fine grained alloys which causes a significant increase in the mechanical properties such as tensile strength and hardness. In the present study the microstructure of 6082 aluminium alloy after hydrostatic extrusion was investigated. Hydroextrusion was performed in three steps with accumulated true strains of 1.34, 2.73 and 3.74 respectively. Microstructural observations were carried out using SEM, TEM and light microscopy. Grain and inclusion sizes, shapes and distribution were investigated in the HE processed samples. The study has shown that the hydrostatic extrusion process results in a profound refinement of both the grain size and the inclusions in 6082 aluminium alloy.

scholarly journals Microstructure and Texture of Hydrostatic Extrusion Deformed Ni Single Crystals and Polycrystal

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
D. Jakubowska ◽  
J. Zdunek ◽  
M. Kulczyk ◽  
J. Mizera ◽  
K. J. Kurzydłowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Single Crystal ◽  
Single Crystals ◽  
Relevant Literature ◽  
Hydrostatic Extrusion ◽  
Total Deformation ◽  
Polycrystalline Nickel ◽  
Before And After

The differences in the microstructure and texture of two Ni single crystals, with different initial orientations (100and110), and of polycrystalline nickel, before and after severe plastic deformation (SPD) produced by hydrostatic extrusion (HE), have been investigated. The crystals were deformed by a two-step HE process with a total deformation value ofε=1.2. The global texture, mechanical properties, and microstructure were examined after the deformation. In every investigated sample, the presence of111fibre texture was noted, while the starting orientation of a100Ni single crystal was preserved in 50% of the volume. The results obtained were compared with the relevant literature data.

The Influence of the Initial State on Microstructure and Mechanical Properties of Hydrostatically Extruded Titanium

2008 ◽  
Vol 140 ◽  
pp. 191-196 ◽  
Author(s):  
Krzysztof Topolski ◽  
Halina Garbacz ◽  
Wacław Pachla ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Extrusion Process ◽  
Hydrostatic Extrusion ◽  
Initial Condition ◽  
Optimum Conditions ◽  
Initial State ◽  
Intended Application ◽  
Extruded Product

Titanium was subjected to hydrostatic extrusion, a method of producing Severe Plastic Deformation (SPD). The experiments were aimed at refining the microstructure of the titanium in order to improve some of its mechanical properties. The effect of the initial state of titanium on the process of extrusion process and the final product was investigated. The results of these investigations are used to establish the optimum conditions for the hydrostatic extrusion process and more easily selecting the initial condition of the material according to the intended application of the extruded product.

Severe Plastic Deformation Induced in Al, Al-Si, Ag and Cu by Hydrostatic Extrusion

2014 ◽  
Vol 59 (1) ◽  
pp. 59-64 ◽  
Author(s):  
M. Kulczyk ◽  
S. Przybysz ◽  
J. Skiba ◽  
W. Pachla
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Hydrostatic Extrusion ◽  
Adiabatic Heating ◽  
High Quality ◽  
Aluminum Silicon Alloy ◽  
Quality Surface ◽  
High Quality Surface

Abstract The study was concerned with the effect of severe deformation induced in one pass, by hydrostatic extrusion on the properties of fine aluminum, aluminum-silicon alloy, copper and silver wires. The influence of adiabatic heating which takes place during deformation on the mechanical properties and microstructure of the wires was examined. The quality of the surface of the wires was estimated. It has been demonstrated that fine aluminum and silver wires processed by hydrostatic extrusion have very good mechanical properties and a high-quality surface.

Severe plastic deformation of Al-1%Cu Alloy processed by a Simple Cyclic Extrusion Compression technique

2018 ◽  
Vol 1 (1) ◽  
pp. 77-90
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen A. Hassan
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Behavior ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Compression Technique ◽  
Cu Alloy ◽  
Cyclic Extrusion Compression

Severe plastic deformation is an effective method for improving the mechanical properties of metallic alloys through promoting the grain structure. In the present work, simple cyclic extrusion compression technique (SCEC) has been developed for producing a fine structure of cast Al-1 wt. % Cu alloy and consequently enhancing the mechanical properties of the studied alloy. It was found that the grain structure was significantly reduced from 1500 µm to 100 µm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of the as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. Also, cyclic extrusion deformation increased the surface hardness of the alloy by 49 % after two passes. FE-simulation model was adopted to simulate the deformation behavior of the material during the cyclic extrusion process using DEFORMTM-3D Ver11.0. The FE-results revealed that SCEC technique was able to impose severe plastic strains with the number of passes. The model was able to predict the damage, punch load, back pressure, and deformation behavior.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

Sign in / Sign up

Export Citation Format

Share Document