scholarly journals PENGGUNAAN LIGHT EMITTING DIODE PADA LAMPU CELUP BAGAN (The Use of Light Emitting Diode on Sunked Lamps of Lift Net)

2016 ◽  
Vol 4 (2) ◽  
pp. 141
Author(s):  
Imanuel M. Thenu ◽  
Gondo Puspito ◽  
Sulaeman Martasuganda
Keyword(s):  
Key Words ◽  
Lower Cost ◽  
Light Emitting Diode ◽  
The Other ◽  
Fluorescent Lamp ◽  
Light Emitting ◽  
Led Light ◽  
Fluorescent Lamps ◽  
Energy Save

<p>ABSTRACT<br />Lift net fishermen usually use fluorescent lamp as attractor to lure fish. As price of fuel rise, fishermen are forced to find another option to change their attractor into some much lower cost and more energy-save lamp, or in other words, to change into LED lamp. This research are providing evidence that sunked LED lamps can be utilized as a helper tools, and also determined the best time for catching fish in the lift net. Two lift net used in this research, one of them used sunked LED lamps and the other used ordinary fluorescent lamps. Lift net are operated as long as 20 nights, with four catching times per night, between 18.00-21.00, 21.00-00.00, 00.00-03.00, and 03.00-06.00. Results showed that LED lamps give a better result with 11 organisms successfully catch (287,6 kg), compared to ordinary fluorescent lamps with only six organisms (238,3 kg). The best time for catching with LED lamps are between 18.00-21.00 (121 kg), while between 21.00-00.00 (67,4 kg), 00.00-03.00 (46,9 kg) and 03.00-06.00 (52,3 kg).<br />Key words: fluorescent lamp, lift net, light emitting diode, Palabuhanratu,sunked lights</p><p>-------</p><p><br />ABSTRAK<br />Nelayan bagan biasa menggunakan lampu fluorescent sebagai atraktor untuk memanggil ikan. Harga bahan bakar yang mahal menyebabkan nelayan harus beralih memakai jenis lampu lain yang hemat energi, seperti lampu LED (light emitting diode) Penelitian bertujuan untuk membuktikan bahwa lampu celup LED dapat digunakan sebagai alat bantu penangkapan ikan pada bagan dan menentukan waktu operasi penangkapan terbaik. Dua bagan digunakan dalam penelitian ini. Masing-masing menggunakan lampu celup LED dan lampu fluorescent. Bagan dioperasikan selama 20 malam. Dalam 1 malam dilakukan 4 kali penangkapan, yaitu antara jam 18.00-21.00, 21.00-00.00, 00.00-03.00 dan 03.00-06.00. Hasil penelitian menunjukkan bahwa penggunaan lampu celup LED pada bagan menghasilkan 11 jenis organisma tangkapan seberat 287,6 kg, atau lebih banyak dari lampu fluorescent sejumlah 6 organisma (238,3 kg). Adapun waktu penangkapan terbaik pada bagan yang menggunakan lampu LED adalah antara pukul 18.00-21.00 yang menghasilkan tangkapan seberat 121 kg, sedangkan 21.00-00.00 (67,4 kg), 00.00-03.00 (46,9 kg) dan 03.00-06.00 (52,3 kg).<br />Kata kunci: lampu fluorescent, bagan, light emitting diode, Palabuhanratu, lampu celup</p>

scholarly journals Redesigning Public Street Lighting Using Photometric Method

2021 ◽  
Vol 3 (1) ◽  
pp. 54-67
Author(s):  
Ade Abdullah ◽  
Muhammad Aziz ◽  
Muhammad Huda
Keyword(s):  
High Efficiency ◽  
Light Emitting Diode ◽  
The Other ◽  
Photometric Method ◽  
Main Road ◽  
Street Lighting ◽  
Light Emitting ◽  
Led Light ◽  
Significant Factors

Street lighting with LED (Light-Emitting Diode) technology is currently the main option of public lighting in almost every country. Even though LED technology is a less costly selection, there needs to be well planned in an attempt of acquiring high efficiency. The photometric approach was tested in this study in order to redesign the existing approach used in street lighting in Indonesia. The redesigning process was carried out using software namely DIALux on two different schemes; one with homogeneous luminaire and the other one with the non-homogeneous luminaire. The results of this study showed that the most significant factors in redesigning street lighting covered types of the lamp, pole distance, pole height, and proper lighting angles which could affect the illumination value on both the main road and the sidewalks. In addition, it has also been proven that a homogeneous approach using LED lamp lighting promoted uniformity as well as optimum illumination.

scholarly journals Design of a Secondary Freeform Lens of UV LED Mosquito-Trapping Lamp for Enhancing Trapping Efficiency

Crystals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 335 ◽  
Author(s):  
Wei-Hsiung Tseng ◽  
Diana Juan ◽  
Wei-Cheng Hsiao ◽  
Cheng-Han Chan ◽  
Hsin-Yi Ma ◽  
...  
Keyword(s):  
Light Intensity ◽  
Intensity Distribution ◽  
Light Emitting Diode ◽  
Trapping Efficiency ◽  
Axially Symmetric ◽  
Light Intensity Distribution ◽  
Light Emitting ◽  
Led Light ◽  
Uv Led ◽  
Freeform Lens

In this study, our proposed ultraviolet light-emitting diode (UV LED) mosquito-trapping lamp is designed to control diseases brought by insects such as mosquitoes. In order to enable the device to efficiently catch mosquitoes in a wider area, a secondary freeform lens (SFL) is designed for UV LED. The lens is mounted on a 3 W UV LED light bar as a mosquito-trapping lamp of the new UV LED light bar module to achieve axially symmetric light intensity distribution. The special SFL is used to enhance the trapping capabilities of the mosquito-trapping lamp. The results show that when the secondary freeform surface lens is applied to the experimental outdoor UV LED mosquito-trapping lamp, the trapping range can be expanded to 100π·m2 and the captured mosquitoes increased by about 300%.

scholarly journals Analysis of Energy and Cost Performance of Retrofitting Fluorescent Tubes with Compact Fluorescent and Light Emitting Diode Lamps

2020 ◽  
pp. 34-46 ◽  
Author(s):  
J. S. Adeleke ◽  
A. B. Wahab ◽  
E. A. Olanipekun
Keyword(s):  
Light Emitting Diode ◽  
Electricity Consumption ◽  
Poor Performance ◽  
Payback Period ◽  
Optimal Performance ◽  
Light Emitting ◽  
Tertiary Institutions ◽  
Fluorescent Lamps ◽  
Significant Difference ◽  
Compact Fluorescent Lamp

Over the years, visual comfort has been described as a major requirement needed to enhance optimal performance of occupants in any learning environment in tertiary institutions. This is reflected in the poor performance of the commonly used Fluorescent Lamps (FL) occasioned by its constant burn-off, high failure rate and reduced durability. Hence, there is a shift to the adoption of Compact Fluorescent Lamp (CFL) and Light Emitting Diode (LED). This study therefore examined the pattern of electricity consumption involving the adoption of FL, CFL and LED in the purposively selected lecture theatres of Obafemi Awolowo University, Ile-Ife, Nigeria. The study was carried out using energy monitor to obtain the consumption data of the lamps for periodic logging at intervals of 1 hr, 3 hrs, 6 hrs, 12 hrs, 1 day, 7 days, 1 month and 3 months respectively; and also to determine the payback period of each of the lamps. From the data collected, patterns of electricity used, electricity savings were calculated and compared to establish performance potentials of each of the lamps. The study found that there was a significant difference in the pattern of electricity consumption of FLs compared with that of CFLs and LEDs, but a reduced margin existed between CFLs and LED lamps. It showed that the FLs consumed 681.576 kWh, 1619.466 kWh and 5652.432 kWh, CFLs consumed 387.302 kWh, 692.479 kWh and 1936.600 kWh, while LED consumed 294.188 kWh, 426.608 kWh and 1499.015 kWh. There were significant differences in consumption with 43, 47 and 65% reduction in electricity consumption using CFLs while 57, 73 and 73% using LED fittings were obtained. The CFLs performed better in terms of return on investments by having a lower payback period when compared to LED. The study concluded that replacing FL with CFL and LED would be desirable option in order to enhance optimal performance of lecture theatres, but in terms of payback period, it would be beneficial to retrofit FLs with CFLs.

scholarly journals Effect of ceramic thicknesses and opacities on water sorption and solubility of a light-curing resin cement by different units

2021 ◽  
Vol 20 ◽  
pp. e211656
Author(s):  
Gabriela Alves de Cerqueira ◽  
Lais Sampaio Souza ◽  
Rafael Soares Gomes ◽  
Giselle Maria Marchi ◽  
Paula Mathias
Keyword(s):  
Water Sorption ◽  
Light Emitting Diode ◽  
Lithium Disilicate ◽  
Resin Cement ◽  
The Other ◽  
Experimental Conditions ◽  
Light Emitting ◽  
Light Curing

Aim: This study evaluated the water sorption and solubility of a light-cured resin cement, under four thicknesses and four opacities of a lithium disilicate ceramic, also considering three light-emitting diode (LED) units. Methods: A total of 288 specimens of a resin cement (AllCem Veneer Trans – FGM) were prepared, 96 samples were light-cured by each of the three light curing units (Valo – Ultradent / Radii-Cal – SDI / Bluephase II – Ivoclar Vivadent), divided into 16 experimental conditions, according to the opacities of the ceramic: High Opacity (HO), Medium Opacity (MO), Low Translucency (LT), High Translucency (HT), and thicknesses (0.3, 0.8, 1.5, and 2.0 mm) (n = 6). The specimens were weighed at three different times: Mass M1 (after making the specimens), M2 (after 7 days of storage in water), and M3 (after dissection cycle), for calculating water sorption and solubility. Results: The higher thickness of the ceramic (2.0 mm) significantly increased the values of water sorption (44.0± 4.0) and solubility (7.8±0.6), compared to lower thicknesses. Also, the ceramic of higher opacity (HO) generated the highest values of sorption and solubility when compared to the other opacities, regardless of the thickness tested (ANOVA-3 factors / Tukey’s test, α = 0.05). There was no influence of light curing units. Conclusion: Higher thicknesses and opacities of the ceramic increased the water sorption and solubility of the tested light-cured resin cement.

scholarly journals PERANCANGAN ALAT PENDETEKSI KELAYAKAN OLI PADA KENDARAAN SEPEDA MOTOR BERBASIS ARDUINO UNO ATMEGA328

SIGMA TEKNIKA ◽  
2019 ◽  
Vol 2 (2) ◽  
pp. 179
Author(s):  
Muhammad Iirsyam
Keyword(s):  
Light Emitting Diode ◽  
Motor Vehicles ◽  
Light Reflection ◽  
Oil Viscosity ◽  
Light Emitting ◽  
Led Light ◽  
Detection Tool ◽  
Arduino Uno ◽  
Resistance Value ◽  
Oil Color

 AbstrakPada kendaraan bermotor pelumasan adalah suatu hal yang sangat penting. Pelumasan berfungsi untuk melumasi komponen logam atau metal yang bergesekan dalam mesin. Untuk menjaga performa mesin kendaraan tetap prima maka kita harus cermat dalam memilih jenis oli yang akan digunakan menurut tingkat kekentalan oli yang dibutuhkan oleh kendaraan yang kita gunakan. Selain itu pemeriksaan dan pergantian oli secara berkala berperan penting dalam menjaga awetnya mesin kendaraan.Untuk membantu dalam pengecekan oli bagi para pemilik kendaran bermotor dalam hal ini sepeda motor dalam itu peneliti merancang sebuah alat pendeteksi kelayakan oli pada kendaraan sepeda motor. Perubahan nilai resistansi dari sensor IR (Infrared Resistor) setelah menerima pantulan cahaya dari LED (Light Emitting Diode) yang diletakkan diatas permukaan oli menyebabkan tegangan yang diterima Arduino Uno microcontroller ATmega328 membaca perubahan warna oli pada sebuah baki oli sepeda motor. Kata kunci : Pengecekan oli, Pantulan cahaya LED, Arduino Uno   AbstractLubrication in motor vehicles is important, lubrication is not only serves to lubricate metal or metal touching or friction in the machine. To maintain the performance of the vehicle's engine is prime, we must carefully select the type of oil to be used according to the oil viscosity level required by the vehicle we use. In addition, inspection and oil change periodically play an important role in maintaining the vehicle's crew.To assist in oil checking for motorised owners in this motorcycle in this case the author devised an oil feasibility detection tool on a motorcycle vehicle. Changes in resistance value from IR sensor (Infrared Resistor) after receiving light reflection from LED (Light Emitting Diode) that is placed above the oil surface causing the received voltage Arduino Uno Microcontroller ATmega328 Read the changes Oil color on a motorcycle oil tray. Keywords: Oil checking, LED light reflection, Arduino Uno

scholarly journals Effects of Light-Emitting Diodes on the Accumulation of Glucosinolates and Phenolic Compounds in Sprouting Canola (Brassica napus L.)

Foods ◽  
2019 ◽  
Vol 8 (2) ◽  
pp. 76 ◽  
Author(s):  
Chang Park ◽  
Nam Kim ◽  
Jong Park ◽  
Sook Lee ◽  
Jong-Won Lee ◽  
...  
Keyword(s):  
Brassica Napus ◽  
Phenolic Compounds ◽  
Light Emitting Diode ◽  
Red Light ◽  
Dry Weight ◽  
Total Phenolic ◽  
Brassica Napus L ◽  
Light Emitting ◽  
Led Light ◽  
Sprout Growth

In this study, we investigated optimal light conditions for enhancement of the growth and accumulation of glucosinolates and phenolics in the sprouts of canola (Brassica napus L.). We found that the shoot lengths and fresh weights of red light-irradiated sprouts were higher than those of sprouts exposed to white, blue, and blue + red light, whereas root length was not notably different among red, blue, white, and blue + red light treatments. The accumulations of total glucosinolates in plants irradiated with white, blue, and red lights were not significantly different (19.32 ± 0.13, 20.69 ± 0.05, and 20.65 ± 1.70 mg/g dry weight (wt.), respectively). However, sprouts exposed to blue + red light contained the lowest levels of total glucosinolates (17.08 ± 0.28 mg/g dry wt.). The accumulation of total phenolic compounds was the highest in plants irradiated with blue light (3.81 ± 0.08 mg/g dry wt.), 1.33 times higher than the lowest level in plants irradiated with red light (2.87 ± 0.05 mg/g dry wt.). These results demonstrate that red light-emitting diode (LED) light is suitable for sprout growth and that blue LED light is effective in increasing the accumulation of glucosinolates and phenolics in B. napus sprouts.

scholarly journals Smart Solar-Powered LED Outdoor Lighting System Based on the Energy Storage Level in Batteries

Buildings ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 119
Author(s):  
Suhil Kiwan ◽  
Anwar Abo Mosali ◽  
Adnan Al-Ghasem
Keyword(s):  
Light Emitting Diode ◽  
Lighting System ◽  
Energy Status ◽  
Sustainable Buildings ◽  
Light Emitting ◽  
Led Light ◽  
Smart Control ◽  
Solar Powered ◽  
Conventional Systems ◽  
New System

A novel smart solar-powered light emitting diode (LED) outdoor lighting system is designed, built, and tested. A newly designed controller, that continuously monitors the energy status in the battery and, accordingly, controls the level of illumination of the LED light to satisfy the lighting requirements and/or to keep the light “on” the longest time possible, has been developed. The use of such a reliable solar energy-driven lighting system, with maximum time when the light is “on”, will eliminate the sudden-death of light problem present in conventional photovoltaic (PV) outdoor lights and, therefore, will enhance the natural surveillance and feeling of safety in sustainable buildings and cities. Furthermore, the new smart control eliminates the overdischarge of the system battery and, thus, ensures a longer lifetime of the system battery. Experimental measurements on a system using a 30 W LED light showed that the operating hours of the new system reached 29.16 h (1750 min), while the operating hours for a similar conventional system were 20.86 h (1252 min). Thus, the new lighting system was demonstrated, securing more than 40% of operating hours than the conventional systems.

1.331μm Narrow-Bandwidth Light Source Based on Polymer Micro-Blazed Grating

2008 ◽  
Author(s):  
Hairong Wang ◽  
Xianni Gao ◽  
Guoliang Sun ◽  
Yulong Zhao ◽  
Zhuangde Jiang
Keyword(s):  
Light Source ◽  
Light Emitting Diode ◽  
Low Cost ◽  
Diffraction Order ◽  
Blazed Grating ◽  
Light Emitting ◽  
Led Light ◽  
Narrow Bandwidth ◽  
Narrow Width ◽  
The Cost

In order to detect methane (CH4) accurately and reliably, this paper presents a sensor which consists of infrared diode, fixtures, blazed grating, to realize the extremely narrow-bandwidth light at wavelength of 1.331μm. Based on factors such as compatibility with the transmission characteristics of silica fiber and the cost, a LED (light-emitting diode) with center wavelength of 1.3μm is selected. The LED light is modulated as the parallel light beam. As the light is incident in a micro-blazed grating with certain angle, by diffraction and interference, the light will output the maximum light intensity of its diffraction order at 1.331 μm, which just is an absorption peak of CH4. Micro-blazed grating applied here is low cost and easy replication by various ways, which makes extreme narrow width wavelength possible. Simulation and analysis indicate the designed prototype can output 1.331μm with bandwidth from 1.32907μm to 1.332495μm. With the light source basing on light dividing system, more reliable and higher sensitive measurement of the dangerous gases such as methane and carbon monoxide (CO) can be realized.

Sign in / Sign up

Export Citation Format

Share Document