scholarly journals Performance Panel Surya Saat Gerhana Matahari Cincin Pada Tanggal 26 Desember 2019 Di Kecamatan Larangan Kabupaten Brebes

2021 ◽  
Vol 22 (2) ◽  
pp. 115
Author(s):  
Su Dar Mono ◽  
Joko Waluyo ◽  
Wahyu Wilopo
Keyword(s):  
Power Plant ◽  
Tilt Angle ◽  
Lithium Battery ◽  
Solar Power ◽  
Load Capacity ◽  
Average Power ◽  
Solar Panel ◽  
Solar Power Plant ◽  
Solar Tracker ◽  
One Year

The purpose of this research is to know the performance of PV technology by using PV Solartracker on the eclipse Ring on 26 December 2019 by varying the net and dirty PV using themethod of Penyesuian sun position In one year. The study simulates using a solar panel capacity of3 watts and 6 volts with a lithium battery load capacity of 4000 mAh, the direction of the solarpanel is in the south with a tilt angle 230 in December each Stepnya solar tracker This 3- hourchanging angle 450, 900 and 1150 This research began from the hour 07:00 to 15:00 hours. Theaverage power of the solar power plant was received by 1.08 Watts, 4.24 Volt, 0.25 amper and netPV capacity of 2108 mAh, while with an average power of 0.83 watts, 4.36 volts, 0.19 Amper andgross PV capacity of 1524 mAh.

scholarly journals Tilt Angle Optimization and Formulation of Annual Adjustment Models for a Solar Power Plant Setup-able Site at Himachal Pradesh, India

2020 ◽  
Vol 9 (7) ◽  
pp. 1181-1185
Keyword(s):  
Power Plant ◽  
Solar Energy ◽  
Tilt Angle ◽  
Solar Power ◽  
Performance Enhancement ◽  
Diffuse Radiation ◽  
Himachal Pradesh ◽  
Solar Power Plant ◽  
Solar Tracking ◽  
Tracking Devices

Solar tracking devices are quite effective for collecting maximum solar radiations but for vastly spread solar energy collection plant, their usage is suppressed due to large cost involvement. The best alternative to this problem is adjustment of tilt angle at most appropriate position. In this study monthly optimum tilt angle have been identified for a solar power plant setup-able site Kalth (φ 30.85046˚, L 77.06153˚), situated at Himachal Pradesh, India. For diffuse radiation estimation, an isotropic model has been used. By considering the impracticality involved in monthly tilt angle adjustment, various annual adjustment models have been formulated for two, three and four annual adjustments. In order to estimate the increment in solar insolation by adopting these models, Performance Enhancement (PE) have been computed from the conventional method of setting the solar collector tilt equal to latitude angle. The results show that PE is maximum for monthly optimum tilt angles followed by M-4 which is a three annual adjustment model. Based on PE requirement, any of the proposed models can be selected for setting up solar energy collection plant at suggested site.

Pengembangan Sistem Pengaturan Suplai Beban (Ats) Pada Pembangkit Listrik Tenaga Hibrid Berbasiskan Mikrokontroler

Kilat ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 261-271
Author(s):  
Sugeng Purwanto
Keyword(s):  
Power Plant ◽  
Alternative Energy ◽  
Power Plants ◽  
Solar Power ◽  
Electrical Energy ◽  
Solar Power Plant ◽  
Solar Panels ◽  
Hybrid Power ◽  
Solar Power Plants ◽  
One Year

ABSTRACT Renewable energy is potential alternative energy to replace the central role of fossil energy which has been going on since the early 20th century. The solar power plant is alternative energy, especially for households and industry, and can be designed as a hybrid power plant consisting of solar panels, batteries, an automatic transfer switch (ATS), and a grid. This research will focus on developing ATS based on a microcontroller. It functions to regulate the load supply automatically from the three sources of electrical energy, like solar panels, batteries, and grid while the microcontroller functions to monitor the transfer of power from the solar power plant to grid and voltage movements in the system so that current and voltage data can be recorded from time to time to improve system reliability, effectiveness, and efficiency of the tool. ATS components consist of MCB, magnetic contactor, timer H3CR, relay, 2000VA inverter, solar charge controller 100A, NodeMCU ESP8266 IoT, and battery 12V 100AH. This research is conducted in one year to produce ATS based on a microcontroller that can automatically regulate the supply of loads from the three sources of electrical energy with a good level of efficiency and stability.  Keywords: solar power plants, hybrid power plants, an automatic transfer switch.  ABSTRAK Energi baru terbarukan merupakan energi alternatif yang potensial untuk menggantikan peran sentral dari energi fosil yang telah berlangsung sejak awal abad ke 20. PLTS merupakan salah satu energi alternatif penyedia energi listrik untuk rumah tangga dan industri serta dapat dirancang sebagai sistem pembangkit listrik tenaga hibrid (PLTH) yang terdiri dari panel surya, baterai, sistem pengaturan beban atau ATS (automatic transfer switch) dan jaringan PLN. Peneltian difokuskan pada pengembangan sistem ATS berbasiskan mikrokontroler. ATS berfungsi untuk mengatur suplai beban secara otomatis dari ketiga sumber energi listrik yaitu panel surya, baterai dan PLN sedangkan mikrokontroler berfungsi memonitor perpindahan daya dari PLTS ke sumber PLN dan pergerakan tegangan pada sistem sehingga dapat dilakukan pencatatan data arus dan tegangan dari waktu ke waktu sehingga dapat meningkatkan keandalan sistem, efektifitas dan efisiensi alat. Komponen ATS terdiri dari MCB, magnetic contactor, timer H3CR, relay, inverter 2000VA, solar charge controller 100A, NodeMCU ESP8266 IoT, dan baterai 12V 100Ah. Penelitian ini akan dilakukan dalam periode satu tahun menghasilkan ATS berbasiskan mikrokontroler yang dapat mengatur suplai beban secara otomatis dari ketiga sumber energi listrik dengan tingkat efisiensi dan kestabilan yang baik. Tim penelitian ini tediri dari 3 orang dan berasal dari program studi teknik elektro, IT PLN.  Kata kunci: pembangkit listrik tenaga surya, pembangkit listrik tenaga hibrid, pengaturan suplai beban.

scholarly journals Short term cloud nowcasting for a solar power plant based on irradiance historical data

2018 ◽  
Vol 18 (03) ◽  
pp. e21 ◽  
Author(s):  
Rafael Caballero ◽  
Luis F. Zarzalejo ◽  
Álvaro Otero ◽  
Luis Piñuel ◽  
Stefan Wilbert
Keyword(s):  
Neural Network ◽  
High Resolution ◽  
Power Plant ◽  
Solar Power ◽  
Historical Data ◽  
Prediction Methods ◽  
Solar Power Plant ◽  
Short Term ◽  
Temporal Series ◽  
One Year

This work considers the problem of forecasting the normal solar irradiance with high spatial and temporal resolution (5 minutes). The forecasting is based on a dataset registered during one year from the high resolution radiometric network at a operational solar power plan at Almeria, Spain. In particular, we show a technique for forecasting the irradiance in the next few minutes from the irradiance values obtained on the previous hour.  Our proposal employs a type of recurrent neural network known as LSTM, which can learn complex patterns and that has proven its usability for forecasting temporal series. The results show a reasonable improvement with respect to other prediction methods typically employed in the studies of temporal series.

Enhancing performance of maintenance in solar power plant

2019 ◽  
Vol 26 (4) ◽  
pp. 575-591
Author(s):  
Jittra Rukijkanpanich ◽  
Mathurot Mingmongkol
Keyword(s):  
Power Plant ◽  
Failure Modes ◽  
Solar Power ◽  
Electrical Equipment ◽  
First Year ◽  
Solar Power Plant ◽  
Maintenance Strategy ◽  
Content Type ◽  
One Year ◽  
Practical Implications

Purpose The purpose of this paper is to enhance the performance of maintenance in a solar power plant by implementing the proactive maintenance (PaM) strategy, measured by the availability and the total maintenance workload. Design/methodology/approach The prior maintenance strategy was reviewed, and then the strategy was adjusted to focus on PaM. Failure modes and effects analysis (FMEA) was a tool for analyzing the severity and occurrence of the failure modes and effects. Then, the Why‒Why analysis was used for investigating the root causes of failures. The countermeasures were drawn, and the preventive maintenance (PM) plan was revised and carried out. The total maintenance, the PaM and reactive maintenance workload, was obtained, and then the improvements were determined. The values of availability were also obtained. Findings Previously, the appeared maintenance strategy was not clearly defined. It seemed to have reactive maintenance coupled with PM; it was checked once a year, and corrective actions were made when something wrong was found. Then the management team observed an increase in the reactive maintenance workload, whereas the values of availability were not consistent and tended to drop. After implementing the new maintenance strategy, PaM, the total maintenance workload decreased 14 percent in one year. The average availability of the solar power plant improved from 0.9943 to 0.9969, and the values of availability had better consistency. Practical implications The PaM can be applied to solar power plant without limiting the prior maintenance strategy and the complexity of production or machinery. The solar power plant is a quite simple production, and most machines consist of electrical equipment and electrical circuits. The PaM supports to analyze the failure modes, the consequence of the failure events and failure effects, and to decide what should be done. Importantly, PaM can reduce total maintenance workload while the value of availability is higher and consistent. Originality/value This paper states how to successfully implement the PaM for the solar power plant. Previously, the plant did not have a clearly defined maintenance strategy; it was checked once a year, and it was corrected when abnormalities were detected. The PaM strategy provides tools and processes for failures and effects analysis. Although there was a more workload of PM, the total maintenance workload decreased, even in the first year.

scholarly journals Implementasi grid tie inverter pada pembangkit listrik tenaga surya on grid untuk golongan pelanggan rumah tangga masyarakat perkotaan

JURNAL ELTEK ◽  
2021 ◽  
Vol 19 (1) ◽  
pp. 108
Author(s):  
Herwandi
Keyword(s):  
Renewable Energy ◽  
Power Plant ◽  
Solar Energy ◽  
Solar Power ◽  
Average Power ◽  
Electricity Production ◽  
Solar Power Plant ◽  
Solar Panels ◽  
Fossil Energy ◽  
Electricity Network

Terbatasnya energi fosil di Indonesia menyebabkan adanya pengembangan energi baru terbarukan. Energi terbarukan merupakan energi non-fosil yang berasal dari alam. Pemanfaatan energi surya bisa dilakukan dengan membangun Pembangkit Listrik Tenaga Surya (PLTS). Perencanaan PLTS menggunakan sistem on grid, sistem masih terkoneksi dengan jaringan PLN. Sistem dimanfaatkan sebagai backup untuk aliran listrik. Sistem akan bekerja secara otomatis ketika aliran listrik PLN terputus dengan memanfaatkan panel ATS (Automatic Transfer Switch). Pembangkit listrik tenaga surya sistem on grid ini cocok diterapkan di perumahan dengan memanfaatkan atap sebagai ruang untuk menyerap energi matahari. Sistem ini jika dipasang bersamaan dengan PLN akan mengurangi pengeluaran biaya listrik. Penerapan sistem atau prinsip kerja PLTS Grid Tie System ini dapat dijalankan dengan sistem kelistrikan PLN. Dalam sistem ini, jaringan listrik PLN berperan sebagai penyalur atau penghubung arus listrik yang berasal dari panel surya yang dialirkan pada beban. Dengan begitu pada siang hari, penggunaan listrik dapat memanfaatkan energi listrik dari sinar matahar dan pada malam hari karena tidak ada sinar matahari menyebabkan tidak ada produksi listrik dari solar panel, maka dapat tetap menggunakan arus listrik yang berasal dari PLN. Perencanaan dilakukan dengan pemilihan komponen PLTS, beban yang dibutuhkan 900Watt, lama waktu penyinaran efektif 10 jam/hari. kemudian melakukan perhitungan komponen PLTS, menentukan tata letak penempatan panel surya dan panel ATS (Automatic Transfer Switch) yang digunakan untuk membackup apabila jaringan listrik PLN terputus. Dari hasil pengukuran arus, tegangan dan daya di dalam rumah pada jam 07.00 sampai dengan 17.00 pada waktu cuaca cerah, yaitu sebelum Grid Tie Inverter dihubungkan ke jala-jala dihasilkan daya rata-rata, P=606,105Watt dan setelah Grid Tie dihubungkan ke jala-jala, P=292,63 Watt. Jadi penghematan daya beban di rumah yang dihasilkan sebesar 52 % dalam satu hari. Limited fossil energy in Indonesia has led to the development of new and renewable energy. Renewable energy is non-fossil energy that comes from nature. Utilization of solar energy can be done by building a Solar Power Plant (PLTS). PLTS planning uses an on-grid system, the system is still connected to the PLN network. The system is used as a backup for electricity. The system will work automatically when the flow of PLN electricity is cut off by utilizing an ATS (Automatic Transfer Switch) panel. This on-grid solar power plant system is suitable for residential use by utilizing the roof as a space to absorb solar energy. This system if installed together with PLN will reduce expenditure of electricity costs. The application of the system or the working principle of the PLTS Grid Tie System can be run with the PLN electrical system. In this system, the PLN electricity network acts as a distributor or connector for the electricity that comes from the solar panels that are flowed to the load. That way during the day, the use of electricity can take advantage of electrical energy from the sun and at night because there is no sunlight it causes no electricity production from solar panels, it can still use the electric current that comes from PLN. Planning is done by selecting the PLTS component, the load required is 900 Watt, the duration of effective irradiation is 10 hours / day. Then calculate the PLTS components, determine the layout of the placement of the solar panels and ATS (Automatic Transfer Switch) panels which are used to back up when the PLN electricity network is interrupted. From the results of measuring currents, voltages and power in the house at 07.00 to 17.00 when the weather is clear, that is, before the Grid Tie Inverter is connected to the grid, the average power is generated, P = 606.105Watt and after the Grid Tie is connected to the grid mesh, P = 292.63 Watts. So, the resulting load power savings at home is 52% in one day

Operating Experience of a 20kW Rooftop Solar Power Plant

2018 ◽  
Author(s):  
P. K. Verma ◽  
A. K. Vishnoi ◽  
Naveen Kumar ◽  
Arun K. Nayak ◽  
G. J. Gorade ◽  
...  
Keyword(s):  
Power Plant ◽  
Solar Power ◽  
Operating Experience ◽  
Solar Power Plant ◽  
Rooftop Solar
Sign in / Sign up

Export Citation Format

Share Document