scholarly journals Algorithms for estimating equivalent resistances of in-plant electrical networks

2021 ◽  
Vol 23 (4) ◽  
pp. 3-13
Author(s):  
E. Yu. Abdullazyanov ◽  
E. I. Gracheva ◽  
A. N. Gorlov ◽  
Z. M. Shakurova ◽  
T. V. Tabachnikova ◽  
...  
Keyword(s):  
Electric Power ◽  
Reference Values ◽  
Power Supply ◽  
Electrical Energy ◽  
Energy Losses ◽  
Equivalent Resistance ◽  
Electrical Networks ◽  
Contact Devices ◽  
Power Point ◽  
Plant Power

THE PURPOSE. Investigation of the degree of influence of the characteristics of in- plant electrical networks on the reliability of the results in the algorithms for estimating equivalent resistances. METHODS. When solving this problem, a study of the radial power supply scheme of the tool shop section was carried out with the calculation and modeling of equivalent and reference values of the circuit resistances. Algorithms and methods for estimating the values of equivalent resistances have been developed, taking into account the main technical characteristics of in-plant networks.RESULTS. The data of calculations of the equivalent resistance values of the circuits with an assessment of the heating factor of the conductors and the resistance factor of the contact devices are analyzed. The proportions of the influence of the resistances of the contact equipment and lines, taking into account the number of electric power receivers connected to the power point, on the value of the equivalent resistances of the circuit are revealed. CONCLUSION. The article develops algorithms for estimating the values of equivalent resistances of in-plant power supply circuits. Nomograms are presented that take into account the number and length of the circuit lines with the allocation of the zone of accounting for the resistances of contact equipment in the equivalent resistances of the circuits. The obtained algorithms and results are recommended to be used to clarify the amount of power and electrical energy losses in the intra- factory networks, which will increase the reliability of calculations.

scholarly journals Calculations, norming and reducing of electrical energy losses in city electrical networks

2019 ◽  
Vol 21 (3) ◽  
pp. 46-54
Author(s):  
A. V. Lykin ◽  
E. A. Utkin
Keyword(s):  
High Voltage ◽  
Power Transmission ◽  
Low Voltage ◽  
Demand Curve ◽  
Electrical Energy ◽  
Electrical Network ◽  
Energy Losses ◽  
Capital Investments ◽  
Electrical Networks

The article considers the feasibility of changing the structure of a distribution electrical network by transferring points of electricity transformation as close to consumers as possible. This approach is based on installation of pole-mounted transformer substations (PMTS) near consumer groups and changes the topology of the electrical network. At the same time, for groups of consumers, the configuration of sections of the low-voltage network, including service drops, changes. The efficiency of approaching transformer substations to consumers was estimated by the reduction in electrical energy losses due to the expansion of the high-voltage network. The calculation of electrical losses was carried out according to twenty-four hour consumer demand curve. To estimate the power losses in each section of the electrical network of high and low voltage, the calculated expressions were obtained. For the considered example, the electrical energy losses in the whole network with a modified topology is reduced by about two times, while in a high-voltage network with the same transmitted power, the losses are reduced to a practically insignificant level, and in installed PMTS transformers they increase mainly due to the rise in total idle losses. The payback period of additional capital investments in option with modified topology will be significantly greater if payback is assessed only by saving losses cost. Consequently, the determination of the feasibility of applying this approach should be carried out taking into account such factors as increasing the reliability of electricity supply, improving the quality of electricity, and increasing the power transmission capacity of the main part of electrical network.

scholarly journals DIGITALIZATION OF THE ELECTRIC POWER METERING SYSTEM

2020 ◽  
pp. 74-83
Author(s):  
Ayrat G. Ziganshin ◽  
Georgi M. Mikheev
Keyword(s):  
Electric Power ◽  
Electrical Power ◽  
Electrical Energy ◽  
Smart Devices ◽  
Electrical Networks ◽  
Federal Law ◽  
Useful Power ◽  
The Republic ◽  
Power Metering ◽  
Electrical Power Consumption

The article deals with the issue of paying for electricity transmission services by consumers in connection with the introducing on the 1st of July, 2020 the Federal Law no. 522-FZ dated December 27, 2018 and the requirements for smart devices and electricity metering systems. This topic is one of the key points in the fight against non-payments for electrical energy, reducing business losses. The article draws attention to the change in the relationship between a consumer of electrical power and its supplier after the introduction of the above-mentioned law. The opportunities of intelligent electricity metering systems are examined as well as their features and some of their characteristics are given. On the example of the Verkhneuslonsky region of the Republic of Tatarstan, served by the branch of JSC “Network Company” Buinsky electrical networks, a comparative analysis of electrical power consumption is presented according to the data of those consumers who have smart metering devices installed and those who use ordinary counters. It is shown that installation of intelligent electric power metering systems made it possible to increase the useful power supply for the observed period by 15.5% in 2020 against 1.8% when using traditional counters for the same period of 2019.

Approach to the location of distributed generation sources in the structure of electrical networks

2021 ◽  
pp. 75-86
Author(s):  
A. Gai ◽  
◽  
V. Gulevich ◽  
Keyword(s):  
Electric Power ◽  
Quality Indicators ◽  
Distributed Generation ◽  
Power Supply ◽  
Alternative Energy ◽  
Electric Power Industry ◽  
Energy System ◽  
Electrical Network ◽  
Electrical Networks

Today, the electricity supplier is not able to declare the possible level of quality of electricity supply, and the consumer simply does not have the opportunity to buy such "high-quality" electricity. In such conditions, a differentiated approach to tariff formation is inevitable, which has been implemented in practice today, albeit in its infancy. Further improvement of the tariff-forming mechanism is impossible without creating a "flexible" dependence of the tariff on the quality indicators of the consumer's power supply. Quality indicators, in turn, are based, on the one hand, on the methods and approaches for their determination, and on the other, on statistically reliable data on the elements that make up the equipment in the "generation-consumer" chain. In recent years, there has been a tendency to change the concept of development of the electric power industry, since preference is given to the development of sources of distributed generation. Distributed generation is understood as a source of electrical energy directly connected to the distribution electrical network or connected to it by consumers. Ensuring the socio-economic stability of society and a decent quality of life for the population largely depends on the reliability and efficiency of the functioning of the infrastructure for the supply of fuel and energy resources, in particular, electricity. Excessive losses of electricity during its production, transportation and distribution, as well as an unacceptable level of harmful emissions into the atmosphere, are the cause of interruptions in power supply to consumers and even the threat of systemic accidents in the United Energy System (UPS) of the country. The introduction of alternative energy sources in electric power systems, in addition to reducing the harmful impact on the environment and solving the problems associated with waste pollution during electric power generation, will reduce the use of natural resources and relieve the backbone and distribution power lines. As part of the scientific search, an approach was proposed, which is the basis for calculations to determine the optimal installation locations for sources of distributed generation of an average overhead line. The results obtained are presented in the framework of a joint technical meeting of leading specialists of operating enterprises, the customer and the staff of the Department of Power Supply named after V.M. Sinkova NULES of Ukraine.

scholarly journals On the influence of electric power quality on the decimation of currents and voltages of utility frequency

2021 ◽  
Vol 288 ◽  
pp. 01022
Author(s):  
Gennady Vagin ◽  
Alexander Kulikov ◽  
Alexander Sevostyanov ◽  
Anatoly Fitasov
Keyword(s):  
Electric Power ◽  
Power Quality ◽  
Harmonic Component ◽  
Electric Power Industry ◽  
Digital Signal ◽  
Electrical Energy ◽  
Sampling Frequency ◽  
Electrical Network ◽  
Electrical Networks ◽  
Electric Power Quality

The electric power industry cannot develop without analyzing the factors that affect the shape of currents and voltages when determining the parameters of the electric network mode in the context of the introduction of modern means of intellectualization into the structure of power supply systems. The share of equipment affecting the electric power quality reaches 90% in modern electrical networks. This leads to the appearance of noise in the network that reduces the quality of electrical energy, voltage distortion by higher harmonic components in particular, and affects the adequacy of the parameters of the electrical network adopted by automatic control devices. The article presents the results of digital signal processing containing distortions in the form of a harmonic component with a decrease in the sampling frequency. It is shown that a decrease in the sampling frequency does not exclude the effect of higher harmonics on the result of processing signals, including high-frequency distortions.

scholarly journals Solving optimization problems when designing power supply circuits

2019 ◽  
Vol 124 ◽  
pp. 04011 ◽  
Author(s):  
O. V. Shemelova ◽  
E. V. Yakovleva ◽  
T. G. Makuseva ◽  
I. I. Eremina ◽  
O. N. Makusev
Keyword(s):  
Electric Power ◽  
Power Supply ◽  
Optimization Problems ◽  
Cost Minimization ◽  
Mathematical Problem ◽  
Power Lines ◽  
Practical Significance ◽  
Electrical Network ◽  
Power Network ◽  
Electrical Networks

One of the quickly developing trends in the optimization of electric power grids is system development of operation and optimization of branch circuits which are based on linear programming problems. One of its categories is traffic problem. The paper discusses the formulation of various types of transport optimization problems used in the design of the most efficient power supply systems in the real sector of economy. The construction of arithmetic models of problems is carried out. Their optimality criterion is cost minimization for the design of electrical network diagrams consisting of power lines connecting sources and consumers. Examples of designing optimization power layout in mathematical problems considering the transmission capacity of power lines is given. The paper also touches upon a mathematical problem considering possible transit of capacities. The task is to build a mathematical model and solve problems that ensure minimization of process losses and losses of power when designing electrical networks. The results of solving problems are presented in the form of power supply circuits corresponding to the most optimal linking of source and consumer nodes. The work is of a scientific and practical significance as it considers the problem of optimizing economic costs when designing electric power network schemes. Moreover it is based on a qualitatively different level of use of the traffic problem algorithm. The algorithm for solving the minimization problem obtained in this paper allows developing the necessary computing operations as well as quickly obtaining the results of solving the cost optimization problem in the designed electric power network.

The Power Quality Evaluation Method Based on the Matter-Element Comprehensive Evaluation Method

2014 ◽  
Vol 1030-1032 ◽  
pp. 1403-1406 ◽  
Author(s):  
Gang Zhang ◽  
Fu Chao Liu ◽  
Tuo Xie ◽  
Jing Jing Zheng
Keyword(s):  
Electric Power ◽  
Power Quality ◽  
Power Supply ◽  
Evaluation System ◽  
Quality Evaluation ◽  
Evaluation Method ◽  
Comprehensive Evaluation ◽  
Evaluation Model ◽  
Electrical Energy ◽  
Element Model

As for the pricing by electrical energy quality and the decision of rewards and penalties based on the examination at assessment point, Comprehensive evaluation on power quality is one of the principal foundations. To analysis and evaluate electric power quality for electric power company is a focus research at present. In this paper, the power quality evaluation model based on the matter-element extension theory is applied to power quality evaluation service. For power quality evaluation system of the characteristics of the complexity and incompatibility between various indicators hierarchies, this paper applied the theory of matter-element extension constructing Matter-element model, and identified level of power quality of power supply company through the calculation of weight and the correlation service. Taking GanSu Grid Company as an example to evaluate power supply quality, the results show that the evaluation results of power quality evaluation method based on the matter-element evaluation method are more objective, more precise and more reasonable.

scholarly journals Electric power supply management of the construction site in the interests of facilitating electrical safety

2019 ◽  
Vol 140 ◽  
pp. 08006 ◽  
Author(s):  
Maxim Polyukhovich ◽  
Vyacheslav Burlov ◽  
Victor Mankov ◽  
Amangeldy Bekbayev
Keyword(s):  
Electric Power ◽  
Power Supply ◽  
Electrical Energy ◽  
Complex Problem ◽  
Industrial Safety ◽  
Electrical Safety ◽  
Construction Site ◽  
Construction Work ◽  
Electric Power Supply ◽  
Critical Resource

A critical resource in construction work is electricity. Various problems that can lead to a breakdown of the electric power supply to the construction site can arise during its active operation. The basis of the activity is the decision of the person. Activity is based on the model. The dependence of human activity on electrical energy has formed the need to ensure uninterrupted electric power supply. To solve the complex problem of electric power supply, it is necessary to develop a theory. A properly constructed theory has three levels, three components: methodology, methods, technology. The decision maker (DM) perceives the world around him and carries out his activities through processes. A process is an object in action at a fixed purpose. A constructive methodology should form the condition for the existence of a process with which the DM works. The goal of research is to select and justify the conditions for the existence of the electric power supply process in the interests of guaranteed achievement of the goal of the industrial safety.

scholarly journals DEVELOPMENT PROSPECTS OF EXTERNAL POWER SUPPLY ELECTRICAL NETWORKS OF TRACTION SUBSTATIONS

2020 ◽  
Vol 1 (154) ◽  
pp. 8-15
Author(s):  
I. Domanskyi ◽  
О. Kozlova
Keyword(s):  
Power Supply ◽  
Electrical Equipment ◽  
Energy Losses ◽  
Electric Transport ◽  
Electrical Networks ◽  
Traction Substations ◽  
External Power ◽  
Traction Power Supply ◽  
Traction Power ◽  
External Power Supply

In the paper on the basis of the analysis of classical power schemes traction substations of railways and urban electric transport conceptual directions of development of electric networks of external power supply of traction substations in the conditions of market economy and normative requirements of the electric power industry of Ukraine are developed, which allow to provide energy saving modes of their operation. Based on system analysis of domestic and foreign traction power supply systems of railways and electric transport of large cities, the concept of their development is substantiated and proposed by increasing the supply voltage of traction substations and minimizing capacity upflows and energy losses, which provides resource and energy savings. It is suggested that the investment programs of the structures that are part of Corporation «Ukrzaliznytsia» and the municipal services be synchronized according to their technological indicators, as well as according to the criteria of energy efficiency and quality of energy supply with similar investment programs of external energy. For reduction of energy losses, it is proposed: realization of rational schedule of train movement and deep high voltage inputs with the prospect of transition to own 110 kV distribution networks, modernization and equipping of modern rolling stock electrical equipment and infrastructure of the main and perspective directions of the railways. The need to expand tram and trolleybus lines and modernize power supply devices in terms of resource conservation requires new technologies for the design, construction and operation of the facilities of municipal enterprise «Miskelektrotransservice». Such technologies have been implemented by the «DAK-Energetika» enterprise in the manufacture of modern electrical equipment of municipal enterprise «Miskelektrotransservice» TS. The most important tasks are the improvement of stationary and mobile substations and other linear facilities of traction power supply by completing functional modular blocks with modern switchgear with digital relay protection and diagnostics of traction networks; local and remote control of switchgear devices, as well as switch diagnostics and self-diagnosis. Keywords: external power supply, traction substations, electrical networks, power systems operation modes.

scholarly journals Analysis of reliability of power supply of consumers in non-full-phase modes using adaptive models of their calculation

2019 ◽  
Vol 139 ◽  
pp. 01012
Author(s):  
T.N. Nasirov ◽  
V.A. Nepomnyashchiy ◽  
O.V. Radionova
Keyword(s):  
Power Systems ◽  
Electric Power ◽  
Power Supply ◽  
Adaptive Methods ◽  
Electric Power Systems ◽  
Electricity Supply ◽  
Electrical Networks ◽  
Adaptive Models

Reviewed and analyzed issues related to the reliability of electricity supply in non-full-phase modes of electrical networks, to calculate which use adaptive methods, is built on one Central principle of modeling the modes of electric power systems (EPS). Special attention is paid to the calculation of damages from no full provided of electricity in non-full-phase modes.

Sign in / Sign up

Export Citation Format

Share Document