scholarly journals Physical layer synchronization algorithms for signal-code sequence increasing noise immunity of dvb-s2x standard vl-snr mode

2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
L. A. Antiufrieva ◽  
◽  
K. K. Iansitov ◽  
A. V. Dvorkovich
Keyword(s):  
Noise Immunity ◽  
Signal To Noise Ratio ◽  
Physical Layer ◽  
Code Sequence ◽  
Signal To Noise ◽  
Synchronization System ◽  
Noise Ratio ◽  
Signal Operating

The work is devoted to expanding the noise immunity of the DVB-S2X standard and the VL-SNR mode physical layer synchronization algorithms. The article proposes a signal-code sequence that increases the noise immunity of the signal, operating down to −11 dB signal-to-noise ratio, and a synchronization system for it.

scholarly journals Joint use of frequency-time division and antinoise coding in radio communication systems with FHSS

2021 ◽  
Vol 9 (4) ◽  
pp. 77-84
Author(s):  
A. A. Paramonov ◽  
Van Zung Hoang
Keyword(s):  
Data Transmission ◽  
Communication Systems ◽  
Error Probability ◽  
Noise Immunity ◽  
Signal To Noise Ratio ◽  
Frequency Division ◽  
Radio Communication ◽  
Signal To Noise ◽  
Noise Ratio ◽  
Time Division

In the context of continuous improvement of radio prospecting and active radio jamming technics along with introduction of automated active countermeasures systems (ACS), the frequency-hopping spread spectrum (FHSS) radio communication systems (RCS) are widely used in order to improve reliability and noise immunity of data transmission. The noise immunity of the RCS affected by unintentional or deliberate interference can be significantly perfected by the combined use of frequency-time division and antinoise coding. This paper explores the case when the interference created by an ACS system with a limited transmitter power covers a part of the RCS frequency range. The receiver gets input mix of the wanted signal, the receiver noise, and probably a deliberate interference also considered as a noise. The article analyzes the noise immunity of signals reception with FHSS in the low-speed radio systems with joint use of frequency-time division of information subsymbols and noise combating codes when the deliberate interference destructively impacts a part of the RCS working band. Dependence of the bit error probability on the signal-to-noise ratio is calculated for the joint use of frequency division of information subsymbols and noise combating codes. It is shown that due to effective use of the frequency-energy resource of a radio line, considering the use of correction codes, a quite high noise immunity of RCS under the influence of deliberate interference can be assured. The indicated dependences of the error probability on the signal-to-noise ratio confirm that the reliability of data transmission can be significantly increased by the proper combination of signal spectrum spreading, applying of correction codes, and frequency division of subsymbols followed by their weight processing.

scholarly journals Comparative analysis of noise immunity of reception of nonlinear complex discrete signals with standard signals AFM-16 BPSK

Radiotekhnika ◽  
2020 ◽  
pp. 133-140
Author(s):  
S.G. Rassomakhin ◽  
A.A. Zamula ◽  
I.D. Gorbenko ◽  
Ho Tri Luc
Keyword(s):  
Comparative Analysis ◽  
Error Probability ◽  
Noise Immunity ◽  
Signal To Noise Ratio ◽  
Statistical Simulation ◽  
Gaussian Channel ◽  
Signal To Noise ◽  
Discrete Signals ◽  
Noise Ratio ◽  
Correlation Properties

The article shows that the solution to the problem of increasing the noise immunity (noise immunity and secrecy of functioning) of the ICS can be achieved using systems of nonlinear signals with improved ensemble, structural and correlation properties. Two classes of nonlinear complex discrete signals are considered: characteristic discrete signals (CDS) and cryptographic signals (CS). Methods for the synthesis of these signals are presented. The paper gives a statistical simulation model for studying the noise immunity of various classes of signals in the Gaussian channel. Using this model, estimates of the dependence of the error probability on the signal-to-noise ratio were obtained for various classes of signals, namely: CDS, KS and standard BPSK AFM-16 signals. It is shown that for the signal-to-noise ratio – 10 the error probability for the CDR is 4.6875e-06, for the CS is 3.515625e-06, and for the AFM-16 is 0.002025. Thus, the use of nonlinear complex discrete signals, in particular, CDS and KS, can significantly increase the noise immunity of signal reception in modern ICS. At the same time, taking into account the improved ensemble and structural properties of these nonlinear signals, it is possible to improve significantly the indicators of crypto- and imitation security of the systems functioning.

Recent Trends in Underwater Acoustic Communications

2013 ◽  
Vol 47 (5) ◽  
pp. 45-50 ◽  
Author(s):  
Milica Stojanovic ◽  
Lee Freitag
Keyword(s):  
Performance Metrics ◽  
Signal To Noise Ratio ◽  
The United States ◽  
Physical Layer ◽  
Small Scale ◽  
Underwater Acoustic Communications ◽  
Signal To Noise ◽  
Acoustic Communications ◽  
Underwater Acoustic ◽  
Noise Ratio

AbstractAdvances in underwater acoustic communications technology are being enabled by more access to in-water data and an infusion of new techniques, researchers, and students. In-water data collection is being made possible by robust funding in the United States, the European Union, and other countries, typically to multiorganization consortia working on both physical and network layer research. At the physical layer, single and multicarrier modulation methods continue to be refined, with a focus on both low signal-to-noise ratio, low-rate and high signal-to-noise ratio, high-rate data links. Establishment of performance metrics for adaptive equalizers and other parts of the physical layer continue, and recent work on high-fidelity channel models that mimic the effects of small-scale ocean processes indicates that progress is being made.Research in undersea acoustic networks continues to gain momentum as well, with multiple options available for integrating acoustic propagation models with network simulation, providing common frameworks for basing network design. The combination of these recent advances, plus continued interest by maritime science and industry in wireless communications, means that the field is poised to make new commercial breakthroughs in the next several years.

Determination of the Best Emulsion for the Microscopy of Crystals

1981 ◽  
Vol 39 ◽  
pp. 32-33
Author(s):  
David A. Grano ◽  
Kenneth H. Downing
Keyword(s):  
Spatial Frequency ◽  
Information Transfer ◽  
Signal To Noise Ratio ◽  
Experimental Situation ◽  
Photographic Emulsion ◽  
Modulation Transfer ◽  
Signal To Noise ◽  
Frequency Space ◽  
Noise Ratio

The retrieval of high-resolution information from images of biological crystals depends, in part, on the use of the correct photographic emulsion. We have been investigating the information transfer properties of twelve emulsions with a view toward 1) characterizing the emulsions by a few, measurable quantities, and 2) identifying the “best” emulsion of those we have studied for use in any given experimental situation. Because our interests lie in the examination of crystalline specimens, we've chosen to evaluate an emulsion's signal-to-noise ratio (SNR) as a function of spatial frequency and use this as our critereon for determining the best emulsion.The signal-to-noise ratio in frequency space depends on several factors. First, the signal depends on the speed of the emulsion and its modulation transfer function (MTF). By procedures outlined in, MTF's have been found for all the emulsions tested and can be fit by an analytic expression 1/(1+(S/S0)2). Figure 1 shows the experimental data and fitted curve for an emulsion with a better than average MTF. A single parameter, the spatial frequency at which the transfer falls to 50% (S0), characterizes this curve.

Experiments in Bright-Field Imaging with Hollow-Cone Illumination

1981 ◽  
Vol 39 ◽  
pp. 226-227
Author(s):  
W. Kunath ◽  
K. Weiss ◽  
E. Zeitler
Keyword(s):  
Signal To Noise Ratio ◽  
Carbon Support ◽  
Electronic System ◽  
Optic Axis ◽  
Hollow Cone ◽  
Signal To Noise ◽  
Bright Field ◽  
Noise Ratio ◽  
Single Field ◽  
Field Imaging

Bright-field images taken with axial illumination show spurious high contrast patterns which obscure details smaller than 15 ° Hollow-cone illumination (HCI), however, reduces this disturbing granulation by statistical superposition and thus improves the signal-to-noise ratio. In this presentation we report on experiments aimed at selecting the proper amount of tilt and defocus for improvement of the signal-to-noise ratio by means of direct observation of the electron images on a TV monitor.Hollow-cone illumination is implemented in our microscope (single field condenser objective, Cs = .5 mm) by an electronic system which rotates the tilted beam about the optic axis. At low rates of revolution (one turn per second or so) a circular motion of the usual granulation in the image of a carbon support film can be observed on the TV monitor. The size of the granular structures and the radius of their orbits depend on both the conical tilt and defocus.

Information capacity and bandwidth limitations in the SEM

1989 ◽  
Vol 47 ◽  
pp. 84-85
Author(s):  
D. C. Joy ◽  
R. D. Bunn
Keyword(s):  
Signal To Noise Ratio ◽  
Critical Dimension ◽  
Information Capacity ◽  
Acquisition Time ◽  
Signal To Noise ◽  
Sem Image ◽  
Probe Size ◽  
Minimum Number ◽  
Noise Ratio ◽  
Signal Channel

The information available from an SEM image is limited both by the inherent signal to noise ratio that characterizes the image and as a result of the transformations that it may undergo as it is passed through the amplifying circuits of the instrument. In applications such as Critical Dimension Metrology it is necessary to be able to quantify these limitations in order to be able to assess the likely precision of any measurement made with the microscope.The information capacity of an SEM signal, defined as the minimum number of bits needed to encode the output signal, depends on the signal to noise ratio of the image - which in turn depends on the probe size and source brightness and acquisition time per pixel - and on the efficiency of the specimen in producing the signal that is being observed. A detailed analysis of the secondary electron case shows that the information capacity C (bits/pixel) of the SEM signal channel could be written as :

Speech Reception in the Presence of Classroom Noise

1979 ◽  
Vol 10 (4) ◽  
pp. 221-230 ◽  
Author(s):  
Veronica Smyth
Keyword(s):  
Signal To Noise Ratio ◽  
Learning Processes ◽  
Speech Discrimination ◽  
Signal To Noise ◽  
Speech Reception ◽  
Monosyllabic Words ◽  
Noise Ratio

Three hundred children from five to 12 years of age were required to discriminate simple, familiar, monosyllabic words under two conditions: 1) quiet, and 2) in the presence of background classroom noise. Of the sample, 45.3% made errors in speech discrimination in the presence of background classroom noise. The effect was most marked in children younger than seven years six months. The results are discussed considering the signal-to-noise ratio and the possible effects of unwanted classroom noise on learning processes.

Quantifying the Effects of Background Speech Babble on Preschool Children's Novel Word Learning in a Multisession Paradigm: A Preliminary Study

2020 ◽  
Vol 63 (1) ◽  
pp. 345-356
Author(s):  
Meital Avivi-Reich ◽  
Megan Y. Roberts ◽  
Tina M. Grieco-Calub
Keyword(s):  
Word Learning ◽  
Signal To Noise Ratio ◽  
Preschool Age ◽  
Exposure Condition ◽  
Signal To Noise ◽  
Verbal Recall ◽  
Referent Selection ◽  
Main Effect ◽  
Noise Ratio ◽  
Novel Word Learning

Purpose This study tested the effects of background speech babble on novel word learning in preschool children with a multisession paradigm. Method Eight 3-year-old children were exposed to a total of 8 novel word–object pairs across 2 story books presented digitally. Each story contained 4 novel consonant–vowel–consonant nonwords. Children were exposed to both stories, one in quiet and one in the presence of 4-talker babble presented at 0-dB signal-to-noise ratio. After each story, children's learning was tested with a referent selection task and a verbal recall (naming) task. Children were exposed to and tested on the novel word–object pairs on 5 separate days within a 2-week span. Results A significant main effect of session was found for both referent selection and verbal recall. There was also a significant main effect of exposure condition on referent selection performance, with more referents correctly selected for word–object pairs that were presented in quiet compared to pairs presented in speech babble. Finally, children's verbal recall of novel words was statistically better than baseline performance (i.e., 0%) on Sessions 3–5 for words exposed in quiet, but only on Session 5 for words exposed in speech babble. Conclusions These findings suggest that background speech babble at 0-dB signal-to-noise ratio disrupts novel word learning in preschool-age children. As a result, children may need more time and more exposures of a novel word before they can recognize or verbally recall it.

On the Signal-to-Noise Ratio for Boolean Functions

2020 ◽  
Vol E103.A (12) ◽  
pp. 1659-1665
Author(s):  
Yu ZHOU ◽  
Wei ZHAO ◽  
Zhixiong CHEN ◽  
Weiqiong WANG ◽  
Xiaoni DU
Keyword(s):  
Boolean Functions ◽  
Signal To Noise Ratio ◽  
Signal To Noise ◽  
Noise Ratio

An Over 120dB Dynamic Range Linear Response Single Exposure CMOS Image Sensor with Two-stage Lateral Overflow Integration Trench Capacitors

2020 ◽  
Vol 2020 (7) ◽  
pp. 143-1-143-6 ◽  
Author(s):  
Yasuyuki Fujihara ◽  
Maasa Murata ◽  
Shota Nakayama ◽  
Rihito Kuroda ◽  
Shigetoshi Sugawa
Keyword(s):  
Linear Response ◽  
Dynamic Range ◽  
Signal To Noise Ratio ◽  
Cmos Image Sensor ◽  
Image Sensor ◽  
Signal To Noise ◽  
Single Exposure ◽  
Two Stage ◽  
Noise Ratio ◽  
Maximum Signal

This paper presents a prototype linear response single exposure CMOS image sensor with two-stage lateral overflow integration trench capacitors (LOFITreCs) exhibiting over 120dB dynamic range with 11.4Me- full well capacity (FWC) and maximum signal-to-noise ratio (SNR) of 70dB. The measured SNR at all switching points were over 35dB thanks to the proposed two-stage LOFITreCs.

Sign in / Sign up

Export Citation Format

Share Document