scholarly journals Study of change in beryllium oxide strength properties as a result of irradiation with heavy ions

2021 ◽  
Vol 5 (3) ◽  
pp. 192-199
Author(s):  
M.V. Zdorovets ◽  
A.L. Kozlovskiy ◽  
D.B. Borgekov ◽  
D.I. Shlimas
Keyword(s):  
Heavy Ions ◽  
Mechanical Characteristics ◽  
Bending Strength ◽  
Sharp Decrease ◽  
Beryllium Oxide ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Radiation Doses ◽  
Near Surface ◽  
Ion Energy

The paper presents data on changes in strength properties, including data on microhardness, crack resistance, bending strength and wear of BeO ceramics as a result of irradiation with heavy accelerated ions. The following types of ions were selected as heavy ions: O2+ (28 MeV), Ar8+ (70 MeV), Kr15+ (147 MeV), Xe22+ (230 MeV). Radiation doses were 1013 -1015 ion/cm2 , which make it possible to assess the effect of both single defects arising from radiation, and cluster overlapping defective areas occurring at large radiation doses. During the studies carried out, it was found that an increase in the ion energy and, consequently, in the damaging ability and depth of the damaged area, leads to a sharp decrease in the strength mechanical characteristics of ceramics, which is due to an increase in defective areas in the material of the near-surface damaged layer. However, an increase in irradiation dose for all types of exposure results in an almost equilibrium decrease in strength characteristics and the same trend of change in strength characteristics. The obtained dependencies indicate that the proposed mechanisms responsible for changing the strength properties can, under certain assumptions, be extrapolated to various types of exposure to heavy ions in the energy range (25-250 MeV).

scholarly journals Study of Helium Swelling in Nitride Ceramics at Different Irradiation Temperatures

Materials ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2415 ◽  
Author(s):  
Maxim. V. Zdorovets ◽  
Kanat Dukenbayev ◽  
Artem. L. Kozlovskiy
Keyword(s):  
Crystal Structure ◽  
Surface Layer ◽  
Room Temperature ◽  
Sharp Decrease ◽  
Radiation Doses ◽  
Near Surface ◽  
Helium Bubbles ◽  
Density Of Dislocations ◽  
Nitride Ceramics ◽  
Average Size

This paper presents the results of a systematic study of helium swelling and the subsequent process of degradation of the near-surface layer of aluminum-based nitride ceramics. The samples were irradiated with 40 keV He2+ ions at temperatures of 300 and 1000 K with a fluence of 1 × 1017–5 × 1017 ions/cm2. The choice of radiation doses and temperature conditions was due to the possibility of simulating reactor tests of structural materials. It has been established that an increase in the irradiation fluence leads to the formation of large agglomerates of clusters of helium bubbles, as well as an increase in the degree of roughness and waviness of the surface with the formation of crater-like inclusions. In the case of irradiation at high temperatures, there was a slight decrease in the average size of helium inclusions compared with irradiation at room temperature. However, the density of inclusions and surface roughness were much higher. It is established that irradiation at room temperatures leads to a sharp decrease in ceramics density, as well as deformation of the crystal structure due to an increase in the density of dislocations and macrostresses in the structure. The decrease in ceramics density due to the formation of helium inclusions led to an increase in porosity and a defective fraction in the structure of the surface layer of ceramics.

Specimen Preparation of Near Surface Ion Irradiated Samples

1985 ◽  
Vol 43 ◽  
pp. 170-171
Author(s):  
K. F. Russell ◽  
L. L. Horton
Keyword(s):  
Radiation Damage ◽  
Heavy Ions ◽  
Target Material ◽  
Metal Alloys ◽  
Specimen Surface ◽  
Specimen Preparation ◽  
Particle Accelerators ◽  
Near Surface ◽  
Graaff Accelerator ◽  
Van De Graaff

Beams of heavy ions from particle accelerators are used to produce radiation damage in metal alloys. The damaged layer extends several microns below the surface of the specimen with the maximum damage and depth dependent upon the energy of the ions, type of ions, and target material. Using 4 MeV heavy ions from a Van de Graaff accelerator causes peak damage approximately 1 μm below the specimen surface. To study this area, it is necessary to remove a thickness of approximately 1 μm of damaged metal from the surface (referred to as “sectioning“) and to electropolish this region to electron transparency from the unirradiated surface (referred to as “backthinning“). We have developed electropolishing techniques to obtain electron transparent regions at any depth below the surface of a standard TEM disk. These techniques may be applied wherever TEM information is needed at a specific subsurface position.

scholarly journals Density, hardness and strength properties of densified fir and aspen woods pretreated with water repellents

Holzforschung ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Hüseyin Pelit ◽  
Fatih Emiroglu
Keyword(s):  
Compression Ratio ◽  
Bending Strength ◽  
Linseed Oil ◽  
Vacuum Treatment ◽  
Strength Properties ◽  
Aspen Wood ◽  
Positive Effect ◽  
Water Repellents ◽  
Impregnated Wood ◽  
Compression Temperature

AbstractIn this study, the effect of thermo-mechanical densification on the density, hardness, compression strength, bending strength (MOR), and modulus of elasticity (MOE) of fir and aspen wood pretreated with water repellents was analyzed. Wood specimens were impregnated with paraffin, linseed oil and styrene after pre-vacuum treatment. Then, the impregnated wood specimens were densified with compression ratios of 20 and 40%, and at 120, 150 and 180 °C. The results indicated that the density, hardness and strength properties of the all densified specimens (untreated and impregnated) increased depending on the compression ratio and temperature. For all tested properties, higher increases were obtained in the paraffin and styrene pretreated specimens compared to untreated samples. However, the increase rates in linseed oil pretreated specimens were generally lower than untreated specimens. Regarding water repellents the most successful results in all tested properties were determined in styrene pretreated specimens. The density, hardness and strength properties of all specimens increased with the increase in compression ratio. On the other hand, the increase in the compression temperature negatively affects the properties of untreated and linseed oil pretreated specimens, while having a generally positive effect on the properties of paraffin pretreated specimens. However, all tested properties of styrene pretreated specimens have increased significantly due to the increase in compression temperature. The increasing strength properties of wood as a result of densification have increased much more with paraffin and especially styrene pretreatment. These combinations can be considered as an important potential for applications that require more hardness and strength.

scholarly journals Shear cutting induced residual stresses in involute gears and resulting tooth root bending strength of a fineblanked gear

2021 ◽  
Author(s):  
Daniel Müller ◽  
Jens Stahl ◽  
Anian Nürnberger ◽  
Roland Golle ◽  
Thomas Tobie ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Carrying Capacity ◽  
Bending Strength ◽  
Tooth Root ◽  
Load Carrying Capacity ◽  
Near Surface ◽  
Load Carrying ◽  
Involute Gears ◽  
Cut Surface

AbstractThe manufacturing of case-hardened gears usually consists of several complex and expensive steps to ensure high load carrying capacity. The load carrying capacity for the main fatigue failure modes pitting and tooth root breakage can be increased significantly by increasing the near surface compressive residual stresses. In earlier publications, different shear cutting techniques, the near-net-shape-blanking processes (NNSBP’s), were investigated regarding a favorable residual stress state. The influence of the process parameters on the amount of clean cut, surface roughness, hardness and residual stresses was investigated. Furthermore, fatigue bending tests were carried out using C-shaped specimens. This paper reports about involute gears that are manufactured by fineblanking. This NNSBP was identified as suitable based on the previous research, because it led to a high amount of clean cut and favorable residual stresses. For the fineblanked gears of S355MC (1.0976), the die edge radii were varied and the effects on the cut surface geometry, hardness distribution, surface roughness and residual stresses are investigated. The accuracy of blanking the gear geometry is measured, and the tooth root bending strength is determined in a pulsating test rig according to standardized testing methods. It is shown that it is possible to manufacture gears by fineblanking with a high precision comparable to gear hobbing. Additionally, the cut surface properties lead to an increased tooth root bending strength.

Characteristics of Low Temperature Degradation Free ZTA for Artificial Joint

2014 ◽  
Vol 631 ◽  
pp. 18-22 ◽  
Author(s):  
Junji Ikeda ◽  
Takayuki Murakami ◽  
Takayoshi Shimozono ◽  
Reiji Watanabe ◽  
Mikio Iwamoto ◽  
...  
Keyword(s):  
Low Temperature ◽  
Phase Stability ◽  
Mechanical Characteristics ◽  
Bending Strength ◽  
Accelerated Aging ◽  
Ceramic Materials ◽  
Wear Property ◽  
Artificial Joint ◽  
Four Point Bending ◽  
Bearing Materials

Low temperature degradation free Zirconia toughened alumina (ZTA) has been developed. It is reported that ZTA has higher mechanical strength compared to alumina due to the stress induced transformation and spontaneously transformation of zirconia phase on some ZTA have been occurred. For achieving the higher reliability of artificial joint prosthesis alternative to alumina and other ceramic materials, it is necessary to improve and validate the both mechanical characteristics and phase stability at the same time. We evaluated that microstructure, mechanical characteristics and phase stability of newly developed ZTA (BIOCERAM®AZUL). It was confirmed that four-point bending strength and weibull modulus were extreamly high, and ZTA has higher reliability. There were no significant changes and deterioration in four-point bending strength, crystal structure and wear property with and without accelerated aging test. Newly developed ZTA not only with high mechanical characteristics but also with phase stability could be quite useful as bearing materials in artificial joints for longer clinical use.

General concept of determining the parameters of non-mining walls of ultra-deep diamond deposits development open pits

2021 ◽  
pp. 48-53
Author(s):  
I. V. Zyryanov ◽  
A. N. Akishev ◽  
I. B. Bokiy ◽  
N. M. Sherstyuk
Keyword(s):  
Rock Mass ◽  
Structural Relaxation ◽  
Slope Angle ◽  
Field Tests ◽  
Friction Angle ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Open Pit ◽  
Open Pit Mining ◽  
Relaxation Coefficient

A specific feature of open pit mining of diamond deposits in Western Yakutia is the construction of the open pits in the zone of negative ambient temperatures, which includes thick permafrost rock mass, and which is at the same time complicated by the influence of cryogenic processes on deformation of pit wall benches. The paper presents the comparative analysis of strength characteristics in frozen and thawed rocks, stability of benches during mining, the general geomechanical approach to the determination of parameters of non-mining walls of the ultra-deep open pit diamond mines, and the parameters of nonmining walls and benches. Optimization of open pit wall configuration should primarily be based on the maximum utilization of the strength properties of frozen rocks in combination with the development of new approaches, calculation schemes and methods for assessing stability of open pit walls and benches of unconventional design, including the non-mining vertical benches. The main design characteristic that determines the parameters of open pit walls is the structural tectonic relaxation coefficient, which specifies the calculated value of cohesion in rock mass. For the diamond deposits, the values of the structural relaxation coefficient were obtained in a series of field tests and back calculations. Full-scale tests were carried out both during exploration operations in underground mines and in open pits. The accuracy of determining the values of the structural relaxation coefficient in the range of 0.085–0.11 is confirmed by the parameters of non-mining walls in an open pit mine 385–640 m deep, with overall slope angles of 38–55° and a steeper H 0.35–0.5 lower part having the slope angle of up to 70° with average strength characteristics of 7.85–11.84 MPa and the internal friction angle of 28.1–37.4°. Using the natural load-bearing capacity of rock mass to the full advantage, which the values of the structural relaxation coefficient of deposits show, allows optimization of open pit wall slope design and minimization of stripping operations.

Study on Particleboard made from Nipa palm (Nypa fruticans) stem wood and Rajkoroi (Albizia richardiana) wood

2018 ◽  
Vol 25 (1) ◽  
pp. 15-18
Author(s):  
Md. Mahabubur Rahaman ◽  
◽  
Khurshid Akhter ◽  
S. Hossain ◽  
Md. Rakibul Islam ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Dimensional Stability ◽  
Bending Strength ◽  
Strength Properties ◽  
Wood Chips ◽  
Standard Specification ◽  
Stem Wood ◽  
Nypa Fruticans ◽  
Albizia Richardiana ◽  
Nipa Palm

The study was conducted to find out the suitability of making particleboard using nipa palm (Nypa fruticans) stem wood and rajkoroi (Albizia richardiana) wood chips. Particleboards were fabricated at six different ratios of nipa palm stem and rajkoroi wood chips such as 100:0, 75:25, 50:50, 25:75, 10:90 and 0:100. Characteristics of particleboards such as modulus of rupture, internal bond strength, water absorption, thickness swelling and moisture content were measured. Results shows that particleboards made from 100% rajkoroi wood chips have the highest static bending properties and highest tensile strength properties of other particleboards but 100% nipa palm stem wood chips have the lowest static bending and lowest tensile strength properties of other particleboards. 10% nipa palm stem wood chips particleboard have the highest bending strength and tensile strength is better than 100% nipa palm stem wood chips and other mixing chips of particleboards. Mechanical, water resistance and dimensional stability properties were tested according to Indian standard specification. Tensile strength passed the British and German standard specification and nearest to Bureau of Indian Standard, bending strength was found nearest to Indian Standard but lower than German and British Standard specification. Strength property of rajkoroi wood chips particleboard is higher than nipa palm steam wood chips particleboard but dimensional stability is lower than nipa palm steam wood chips particleboard.

Weldability: Effect of Alloying Element Sc, Mn, and Zr on Alloys of the Al-Mg-Sc-Mn-Zr System

2019 ◽  
Author(s):  
V. I. Lukin
Keyword(s):  
Aluminum Alloys ◽  
Practical Importance ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Mg Alloy ◽  
Alloying Element ◽  
Processing Properties ◽  
Alloys Of The Al ◽  
Effect Of Alloying

Scandium in aluminum alloys behaves as the most efficient modifier of the structure of the material and as an agent suppressing recrystallization. This unique behavior of scandium in alloys of the Al-Mg system greatly increases the strength characteristics, whilst retaining on a higher level the ductility and processing properties of deformed semi-finished products. This article describes the effect of complex alloying the Al-6.3% Mg alloy with scandium, manganese and zirconium on the weldability and strength properties of the material is of considerable scientific and practical importance.Investigations.

Sign in / Sign up

Export Citation Format

Share Document