scholarly journals PENGARUH PENAMBAHAN PASIR PADA ENDAPAN LUMPUR DANAU LIMBOTO SEBAGAI PEMBUATAN BATU BATA

2018 ◽  
Vol 1 (2) ◽  
pp. 8
Author(s):  
Ilyas Ichsan
Keyword(s):  
Mechanical Properties ◽  
Quantitative Research ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Sand Mixture ◽  
The Right ◽  
Lake Sludge

Research on the use of limboto lake sludge as raw material for bricks by adding sand as a mixture of materials using experimental quantitative research. In the study used limboto lake silt with sand mixture with variations of2%, 5%, 7%, 10% and 15%. Related variables are physical and mechanical properties of bricks. The controlling variable is the materials used.The results showed that bricks with raw material from limboto lake sludge with a mixture of sand with variations of 2%,5%, 7%, 10% and 15% did not produce the right composition to have the same quality of bricks with bricks using raw materials clay. Penelitian pemanfaatan endapan lumpur danau limboto sebagai bahan baku batu bata dengan penambahan pasir sebagai bahan campurnya menggunakan penalitian kuantitatif yang bersifat eksperimen. Dalam penelitian digunakan bahan endapan lumpur danau limboto dengan campuran pasir dengan variasi 2%, 5%, 7%, 10% dan 15%. Variabel terkait berupa sifat fisik dan mekanik batu  bata. Variabel pengendali adalah bahan-bahan yang digunakan. Hasil penelitian menunjukan bahwa batu bata dengan bahan baku endapan lumpur danau limboto dengan campuran pasir dengan variasi 2%, 5%, 7% 10% dan 15% tidak  menghasilkan komposisi yang tepat untuk memiliki kualitas batu bata yang sama dengan batu bata yang menggunakan bahan baku tanah liat.

scholarly journals Analysis Physical and Mechanical Of Particle Boards Raw Materials Nipah Fruit Fiber

Teknomekanik ◽  
2019 ◽  
Vol 2 (1) ◽  
pp. 14-19
Author(s):  
M Saddikin ◽  
Hendri Nurdin ◽  
Primawati Primawati
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Average Density ◽  
Raw Material ◽  
Average Moisture Content ◽  
Particle Board ◽  
Wood Particles ◽  
Tapioca Flour

The raw materials of the timber industry, especially furniture, are increasingly difficult to obtain in the quantity and quality needed. The development efforts carried out were utilizing Nipah coir waste as a raw material for making particle boards. Particle boards are panel boards made of wood particles or materials containing lignocellulose. Nipah plants contain 27.3% lignin and 36.5% cellulose which has the potential to be used as raw material for particleboard production. This study aims to reveal the physical and mechanical properties of particleboards made from Nipah fruit fibre with adhesive using tapioca flour. The making of particle board is done with a ratio of 90%: 10%, 80%: 20%, 70%: 30%, 60%: 40%, by giving a pressure of 100 kg / cm2. Particle testing is carried out according to the JIS A 5908 standard (2003). From this study, the optimum results were obtained in variations of 60%:40%. The particle physical properties which have an average density value of 1.15 gr / cm3 and an average moisture content of 5.8%. While the mechanical properties obtained by the value of Modulus of Elasticity an average of 21,188.93 kg / cm2. This shows the particle board variations of 60%: 40% produced to meet the JIS A 5908 (2003) standard. Based on the analysis of the quality variations 60%: 40% of particle boards can be recommended as raw materials for interior furniture.

Dispersing the Charge as a Way to Improve the Quality of Ceramic Bricks

2018 ◽  
Vol 931 ◽  
pp. 558-563 ◽  
Author(s):  
Viktoriya A. Guryeva ◽  
Viktor V. Dubineckij ◽  
Aleksandr V. Doroshin
Keyword(s):  
Mechanical Properties ◽  
Original Composition ◽  
Water Absorption ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Dust Particles ◽  
Drill Cuttings ◽  
Additional Processing ◽  
Grinding Time

Investigations of the influence of dispersion of feedstock on the basis of clay of the Buguruslan deposit and drill cuttings from the facilities of PJSC «Orenburgneft» have been carried out, it is revealed that as the grinding time increases, the content of clay and dust particles increases. Intensive sintering of the samples between 1000 °C and 1100 °C has been established, which is confirmed by the compaction of the samples and the decrease in the water absorption of the ceramic masses. Minimal water absorption, within 2.35%, showed a sample of 3-hour grinding, and a sample of a 2-hour grinding of 8.34%. As a result of the study of dispersion of the charge on the basis of clay raw materials and drill cuttings, it was found that by subjecting the original composition to additional processing, within 2 hours, the physical and mechanical properties of ceramic bricks can be improved.

Production of Cement Blocks and New Ceramic Materials with High Content of Glass Waste

2015 ◽  
Vol 663 ◽  
pp. 34-41 ◽  
Author(s):  
Fernanda Andreola ◽  
Isabella Lancellotti ◽  
Rosa Taurino ◽  
Cristina Leonelli ◽  
Luisa Barbieri
Keyword(s):  
Mechanical Properties ◽  
Environmental Impact ◽  
Economic Burden ◽  
Raw Materials ◽  
Glass Melting ◽  
Physical And Mechanical Properties ◽  
Ceramic Materials ◽  
Raw Material ◽  
Added Value ◽  
Glass Waste

Virgin raw materials can be partially replaced by glass waste in order to reduce the environmental impact being its recycling a significant problem for municipalities worldwide. In Italy in 2013, approximately 1,600,000 tons of container glass have been collected but it was not possible to recycle all of them in the glass melting process.This work is focused on the valorization of glass waste as raw material in new cement and ceramic products, to convert it from an environmental and economic burden to a profitable, added-value resource in the formulation of new mixes. Several parameters, such as grinding, forming, firing, etc. have been studied.It has been optimized the grinding and the reclaiming step of waste to obtain an alternative raw material for hot and cold consolidation processes. Chemical, physical and mechanical properties of products were carried out. The results show new real possibilities to use high amounts of glass waste as an alternative raw material in products consolidated either by hot or cold techniques, reducing the management problems of the glass waste.

scholarly journals STUDY OF RECEIVING WOOD AND PLANT PLASTICS WITHOUT BINDERS IN THE PRESENCE OF CATALYSTS OF POLYOXOMETALLATES TYPE

2018 ◽  
Vol 8 (1) ◽  
pp. 132-138
Author(s):  
Виктор Бурындин ◽  
Viktor Buryndin ◽  
Лариса Бельчинская ◽  
Larisa Belchinskaya ◽  
Андрей Савиновских ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Functional Groups ◽  
Hot Pressing ◽  
Raw Materials ◽  
Flexural Modulus ◽  
Chemical Activation ◽  
Physical And Mechanical Properties ◽  
Strength Properties ◽  
Raw Material ◽  
Plastic Properties

The possibility of obtaining wood and plant plastics without a binder (WP-WB) in the presence of a catalyst of man-ganese-containing sodium vanadomolybdophosphate has been investigated. The use of this catalyst makes it possible to reduce the temperature of hot pressing in closed molds from 1,800°C to 1,600°C. The fractional composition of the initial press raw material influences physical and mechanical properties of WP-WB. Higher values of the plastic properties are obtained by using a 0.7 mm fraction, which is associated with an increased specific surface area of the particles compared to 1.3 mm particles. The results has showed that the samples obtained by using the catalyst have increase in strength properties (flexural strength, flexural modulus, hardness) at lower pressing temperature, but reduction of water resistance performance has been observed . This is explained by the increase in the content of functional groups when using a catalyst. The process of obtaining plastic can be broken down into two successive stages: the first is hydrothermal destruction of lignin-carbohydrate complex (initial moisture of the press raw material is 12%, the temperature of hot pressing in closed molds is 160 ... .180 ° C) and partial chemical activation of lignin as a result of hydrogen peroxide and catalyst application; the second stage - formation of plastic with the formation of a network structure due to the formed functional groups. It is established that the values of physical and mechanical properties of WP-WB are higher than those of plastic obtained on the basis of plant raw materials (PP-WB). This can be explained by the fact that lignin of coniferous species has the guaiacylpropane structure, while plant raw material has a hydroxyphenylpropane structure

scholarly journals SIFAT FISIK DAN MEKANIK PAPAN PARTIKEL BERDASARKAN KOMPOSISI LIMBAH KULIT BUAH PINANG DAN LIMBAH KAYU GERGAJIAN DENGAN VARIASI KADAR PEREKAT

2021 ◽  
Vol 9 (2) ◽  
pp. 207
Author(s):  
Asmawati Wurya Sari ◽  
M Dirhamsyah ◽  
Yuliati Indrayani
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Betel Nut ◽  
Particle Board ◽  
Composition Ratio

This research aimed to analyze the physical and mechanical properties of particleboard based on the composition of raw materials and adhesive content as well as their interaction with the optimum quality of particle boards that meet JIS A 5908-2003 standards. The particleboard was made with a size of 30 cm x 30 cm x 1 cm with a target density of 0.7 g/cm³.  The pressing was done at a temperature of 140°C for 8 minutes with a pressure of 25 kg/cm². The composition ratio of betel nut peel waste and sawdust varied, namely 60% betel nut peel waste: 40% sawdust, 50% betel nut peel waste: 50% sawdust, and 40% betel nut peel waste: sawdust 60%. The adhesive used was Urea Formaldehyde with a concentration of 12%, 14%, and 16%. The results showed that all test values met the JIS A 5908: 2003 standard except the MOE test. The optimum value of particle board of betel nut peel and sawdust was with a composition ratio of 50% betel nut peel waste: 50% sawdust, 16% adhesive content, with a density value of 0.6876 g/cm³, a moisture content of 9,4530%, water absorption 34,5306%, thickness expansion 8,2508%, MOE 12432,6243 kg/cm², MOR 205,8462 kg/cm², adhesive firmness 2,2530 kg/cm², screw holding strength 81,6861 kg/cm².Keywords: adhesive content, betel nut peel waste, material composition, mechanical properties, particleboard, physical.Abstrak Penelitian ini bertujuan untuk menganalisis sifat fisik dan mekanik papan partikel berdasarkan komposisi bahan baku dan kadar perekat serta interaksi keduanya terhadap kualitas papan partikel yang optimum serta memenuhi standar JIS A 5908-2003. Papan partikel dibuat dengan ukuran 30 cm x 30 cm x 1 cm dengan target kerapatan 0,7 g/cm³. Pengepresan  pada suhu 140°C selama 8 menit dengan tekanan 25 kg/cm². Perbandingan komposisi kulit buah pinang dan serbuk kayu gergaji bervariasi yaitu kulit buah pinang 60% : serbuk kayu gergaji 40%, kulit buah pinang 50% : serbuk kayu gergaji 50% dan kulit buah pinang 40% : serbuk kayu gergaji 60%. Perekat yang digunakan adalah Urea Formaldehida dengan konsentrasi 12%, 14% dan 16%. Hasil penelitian menunjukkan semua nilai uji memenuhi standar JIS A 5908 : 2003 kecuali uji MOE. Nilai papan partikel kulit buah pinang dan serbuk kayu gergaji optimum dengan perbandingan komposisi kulit buah pinang 50% : serbuk kayu gergaji 50%, kadar perekat 16%, dengan nilai densitas 0,6876 g/cm³, kadar air 9,4530%, daya serap air 34,5306%, pengembangan tebal 8,2508%, MOE 12432,6243 kg/cm², MOR 205,8462 kg/cm², Keteguhan rekat 2,2530 kg/cm², kekuatan menahan sekrup 81,6861 kg/cm².Kata kunci : papan partikel, kadar perekat, kulit buah pinang, komposisi bahan, sifat fisik dan mekanik.

Raw mix for the production of ceramic paving stones by vibro pressing

2021 ◽  
Vol 2 (80) ◽  
pp. 256-263
Author(s):  
S. A. Montaev ◽  
◽  
B. T. Shakeshev ◽  
B. L. Idirisov ◽  
K. Zh. Dosov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Material Composition ◽  
Raw Material ◽  
Component Mixture ◽  
Mineralogical Characteristics ◽  
Two Component

The article presents the results of studying the physical-mechanical and chemical-mineralogical characteristics of raw materials and suggests a raw material composition based on clay for creating a technology of ceramic paving stones by vibropressing using talc rock. The compositions of ceramic compositions for the production of ceramic paving stones are studied, taking into account the dominant factors of a two-component mixture to improve the molding, drying and physical and mechanical properties of the finished product.

SIFAT FISIS DAN MEKANIS ANYAMAN BAMBAN (Donax canniformis) DENGAN BAHAN STABILISATOR PEG 1000 DAN TANIN KULIT AKASIA

2014 ◽  
Vol 7 (2) ◽  
pp. 23
Author(s):  
Dwi Harsono
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Biological Resources

Bamban (Donax canniformis) is one of the biological resources that grow in the swampy areas and has been used by the community as a raw material in the form of woven handicrafts. Bamban bark that used as raw material woven texture is hard and the surface was very slippery so hard to make. This study was conducted to determine the nature of the characteristics of stem Bamban and determine the effectiveness of the stabilizers PEG 1000 and tannin from extract acacia bark in improving the quality of physical and mechanical properties strands of Bamban. Treatments include immersion with PEG 1000 and acacia bark tannins for 2 hours. Results of the study the effectiveness of treatments of soaking the material stabilizers PEG 1000 and tannins from extract acacia bark all of them can improve the physical and mechanical properties of raw material of Bamban woven handicraft and make it easier for artisans in the process of weaving due to the treated material can make more limp strands of Bamban and not to stiff, in addition to making the product brighter and more attractive.Keywords : bamban, physical properties , mechanical  properties

scholarly journals Some Properties of Eastern Red Cedar (Juniperus Virginiana L.) Particleboard Panels Made Using Modified Starch as Binder

2020 ◽  
Vol 71 (4) ◽  
pp. 371-377
Author(s):  
Onur Ulker ◽  
Salim Hiziroglu
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Juniperus Virginiana ◽  
Modified Starch ◽  
Thickness Swelling ◽  
Eastern Red Cedar ◽  
Red Cedar

The objective of this study was to evaluate physical and mechanical properties of experimental panels manufactured from eastern red cedar (Juniperus virginiana L.) using modified starch as binder. Modulus of elasticity (MOE), modulus of rupture (MOR), internal bond strength (IB), hardness and dimensional stability in the form of thickness swelling and water absorption in addition to surface quality of the samples were tested. Panels were manufactured at three density levels, which are 0.60 g/cm3, 0.70 g/cm3 and 0.80 g/cm3. The highest MOE, MOR and IB values for the samples having 0.80 g/cm3 density were determined as 2207.16 MPa, 15.17 MPa and 0.87 MPa, respectively. Thickness swelling values of the samples soaked in water for 2 h ranged from 15.38 % to 23.23 %. Micrographs taken on the samples using scanning electron microscope revealed that starch was uniformly distributed within the particles. Based on the findings in this study, it appears that eastern red cedar would have a potential as a raw material to manufacture particleboard panel using modifi ed starch as green adhesive with accepted physical and mechanical properties.

Effects of Bamboo Age on the Strength of Board Made from Laccase-Treated Pleioblastus amarus Particle

2011 ◽  
Vol 80-81 ◽  
pp. 207-212 ◽  
Author(s):  
Jin Wang ◽  
Li Liu ◽  
Chun De Jin
Keyword(s):  
Mechanical Properties ◽  
Reactive Oxygen Species ◽  
Free Radicals ◽  
Raw Materials ◽  
Chemical Constituents ◽  
Reactive Oxygen ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Oxygen Species ◽  
Wet Process

The different age pleioblastus amarus particle were taken as the raw materials, and the wet-process bamboo powder-boards were made from the laccase-treated powder by hot pressing. The raw material chemical constituents were analyzed. The reactive oxygen species free radicals produced from the laccase-treated bamboo were detected by electron spin resonance. The physical and mechanical properties of the bamboo particleboards were measured. In order to provide some theoretical basis for producing bamboo particleboard by laccase activation, the relations between physical and mechanical properties of bamboo particle boards and chemical constituents, the reactive oxygen species free radicals were researched.

FEATURES OF TECHNOLOGY FOR PRODUCING CONSTRUCTIONAL HEAT INSULATING CELLULAR CONCRETE BASED ON NONCONVENTIONAL RAW MATERIALS

2016 ◽  
Vol 2 (1) ◽  
pp. 138-143 ◽  
Author(s):  
Строкова ◽  
Valeriya Strokova ◽  
Володченко ◽  
Anatoliy Volodchenko
Keyword(s):  
Mechanical Properties ◽  
High Activity ◽  
Energy Production ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Production Costs ◽  
Raw Material ◽  
Porous Concrete ◽  
Clay Rocks ◽  
Cellular Concrete

It was found that the clay rocks unfinished stage mineral suitable as a raw material for thermal insulation materials construction-autoclaved. High activity of raw rock-forming minerals accelerate the synthesis of tumors and the formation of a rational connection cementitious microstructure that provides high physical and mechanical properties of porous concrete. At the same time by reducing the pressure and time of autoclaving and simplify technology possible reduction of energy production costs by 35%.

Sign in / Sign up

Export Citation Format

Share Document