scholarly journals PERENCANAAN TUBUH BENDUNGANAIR LUAS KABUPATEN KAUR PROVINSI BENGKULU

2019 ◽  
Vol 9 (1) ◽  
pp. 23-37
Author(s):  
Robet Firmansyah ◽  
Besperi Besperi ◽  
Muhammad Fauzi
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
The Body ◽  
Rockfill Dam ◽  
Discharge Plan ◽  
Downstream Slope ◽  
Flow Filtration ◽  
The Stability ◽  
Base Elevation ◽  
Filtration Capacity

The purpose of this study was to plan the dimensions of the dam body that is technically feasible to build, as well as secure the stability. Flood discharge plan used amounted to 1,152 meters cubic/ sec with a return period of 1000 years. Based on the analysis that has been done, get a plan of flood water level is + 303,22 meters, surveillance obtained high of 3,0 meters, the body of the dam crest elevation gained + 306,22 meters high dam that is obtained by subtracting the height elevation of the peak body dam with a base elevation of the dam is 56,16 meters, width of the dam crest beacon of 11.0 meters, rockfill the upstream slope of 1:3 and for rockfill downstream slope is 1: 2,.25. Using the scheme of depression line formation with drainage leg with a graphic way, do not occur out of the body dam seepage and flow filtration capacity value of the calculation, Q = 9,553 x 10-5 meters cubic / sec, smallest than 2% Qinflow mean = 5,785 mmeters cubic / sec, dam secure against flow filtration. The stability of the main dam of landslide with the value of safety factor in a variety of conditions, namely dams both empty and fully charged in a normal state or an earthquake, for rockfill dam by calculating the weight of the dam, sliding moment, pore water pressure and earthquake loads. Using the method of slices Fellenius glide plane, the value obtained above safe rate (1,2), the planneddam safety to landslides

scholarly journals Instrumented Health Monitoring of an Earth Dam

2020 ◽  
Vol 5 (3) ◽  
pp. 26 ◽  
Author(s):  
S.M. Seyed-Kolbadi ◽  
M.A. Hariri-Ardebili ◽  
M. Mirtaheri ◽  
F. Pourkamali-Anaraki
Keyword(s):  
Health Monitoring ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Horizontal Stress ◽  
The Body ◽  
Earth Dam ◽  
Pressure Water ◽  
Stress Ratios ◽  
The Stability ◽  
Term Performance

This work evaluates the stability of the Boostan earth dam by investigating its long-term performance and interpreting the measured data. To measure the dam response, several sensitive locations are instrumented. This process includes measuring various quantities such as pore water pressure, water level, and internal stress ratios using inspection devices such as ordinary and Casagrande piezometers, and total pressure cells. The recorded data shows that the pore pressure is in good agreement with the initial (stable) design condition. The installed piezometers show that the drainage is efficient, and the water table in the body is adequate. The instrument also shows a reasonable horizontal stress in the dam body. Overall, the condition of the case study dam is assessed to be normal. The results of this case report can be used as a guide in similar dams for instrumented health monitoring.

scholarly journals ANALISIS REMBESAN TERHADAP KEAMANAN BENDUNGAN KEDUNG OMBO DI GROBOGAN, JAWA TENGAH

2021 ◽  
Vol 12 (2) ◽  
pp. 79-92
Author(s):  
Rais Buldan ◽  
Suharyanto Suharyanto ◽  
Najib Najib ◽  
Kresno Wikan Sadono
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Good Condition ◽  
Condition Index ◽  
The Body ◽  
Embankment Dam ◽  
Safety Level ◽  
Human Needs ◽  
The Stability

A dam, besides having a great benefits to meet human needs, it also can be a big disaster in addition to the dam collapsing. One of the main causes of failure of an embankment dam is the occurrence of excessive seepage which triggers piping events that can disturb the stability and safety of the dam. In general, the body of the Kedung Ombo Dam is in good condition, but there are several problems, such as the drain holes that are overgrown with dense grass which indicates that seepage has occurred. Therefore, it is necessary to evaluate the seepage to determine the safety level of the Kedung Ombo Dam. This study aims to analyze the condition of pore water pressure and seepage that occurs in the body of the Kedung Ombo Dam and to determine the level of safety of the dam body. The analyze was carried out using seepage monitoring instruments installed on the dam, namely the Piezometer and V-Notch at the Kedung Ombo Dam in 2021. Based on the results of the analysis, it was found that the pore water pressure and seepage discharge that occurred in the Kedung Ombo Dam were generally still within the permissible limits. According to the analysis results of the seepage index, the highest QI value is 0.09 at the maximum flood water level of +95 m, where the safety criteria for the seepage index is QI <1. Therefore it indicates that the seepage condition index at the Kedung Ombo Dam are still in a safe condition.Keywords: pore water pressure, seepage, piezometer, V-Notch, seepage index 

scholarly journals Integrated Simulation Modeling Approach for Investigating Pore Water Pressure Induced Landslides

2022 ◽  
Author(s):  
Sahila Beegum ◽  
P J Jainet ◽  
Dawn Emil ◽  
K P Sudheer ◽  
Saurav Das
Keyword(s):  
Pore Water ◽  
Factor Of Safety ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Simulation Models ◽  
Integrated Simulation ◽  
Hill Slope ◽  
Slope Factor ◽  
The Stability ◽  
The Hill

Abstract Soil pore water pressure analysis is crucial for understanding landslide initiation and prediction. However, field-scale transient pore water pressure measurements are complex. This study investigates the integrated application of simulation models (HYDRUS-2D/3D and GeoStudio–Slope/W) to analyze pore water pressure-induced landslides. The proposed methodology is illustrated and validated using a case study (landslide in India, 2018). Model simulated pore water pressure was correlated with the stability of hillslope, and simulation results were found to be co-aligned with the actual landslide that occurred in 2018. Simulations were carried out for natural and modified hill slope geometry in the study area. The volume of water in the hill slope, temporal and spatial evolution of pore water pressure, and factor of safety were analysed. Results indicated higher stability in natural hillslope (factor of safety of 1.243) compared to modified hill slope (factor of safety of 0.946) despite a higher pore water pressure in the natural hillslope. The study demonstrates the integrated applicability of the physics-based models in analyzing the stability of hill slopes under varying pore water pressure and hill slope geometry and its accuracy in predicting future landslides.

scholarly journals Environmental impact of intensive farming in sloping areas

2018 ◽  
Vol 174 ◽  
pp. 01001
Author(s):  
Giovanni Bosco ◽  
Lucia Simeoni
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Sprinkler Irrigation ◽  
High Yield ◽  
Qualitative And Quantitative ◽  
Intensive Farming ◽  
Yield Production ◽  
Large Water ◽  
The Stability ◽  
Irrigation Runoff

The increased demand for food causes intensive farming with high yield production and large water consumption to extend significantly. Depending on soil properties, seasonal rainfall, surface drainage and water resources, hence the consumption-infiltration balance, the ground water table might be raised or depleted; soils could be saturated or remain partly saturated with negative pore pressures. As a result sloping grounds may become prone to shallow slides, as mudflows, or deep seated movements, involving large volumes of soil, especially after rupture of major watering lines or after long uncontrolled irrigations. Within this framework the paper investigates the possible effects of replacing grassland with intensive apple farming on the stability conditions of slopes. Apples require frequent watering, especially during spring and summer to meet qualitative and quantitative productive standards. Also, sprinkler irrigation is often used to protect against hail. From the precipitation, irrigation, runoff, evaporation and plant transpiration balance, the evolution of the pore water pressure distribution within an average year is calculated. Then the modified shear strength of the unsaturated-saturated soils is determined and the factor of safety against sliding is calculated.

Unsaturated Seepage and Fluid-Solid Coupling Analysis of Rainfall Infiltration of Slope

2011 ◽  
Vol 255-260 ◽  
pp. 3488-3492
Author(s):  
Bao Lin Xiong ◽  
Jing Song Tang ◽  
Chun Jiao Lu
Keyword(s):  
Pore Water ◽  
Unsaturated Flow ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Rainfall Infiltration ◽  
Medium Permeability ◽  
Stability Of Slope ◽  
Transient Seepage ◽  
The Stability ◽  
Unsaturated Seepage

Rainfall is one of the main factors that influence the stability of slope. Rainfall infiltration will cause soil saturation changing and further influence pore water pressure and medium permeability coefficient. Based on porous media saturation-unsaturated flow theory, the slope transient seepage field is simulated under the conditions of rainfall infiltration. It is shown that change of pore water pressure in slope soil lag behind relative changes in rainfall conditions. As the rainfall infiltrate, unsaturated zone in top half of slope become diminution, the soil suction and shear strength reduce, so stabilization of soil slope is reduced.

scholarly journals New technique for predicting the pore water pressure and evaluating the stability of rock-fill dam during impounding

2007 ◽  
Vol 49 (1) ◽  
pp. 3-15
Author(s):  
Yasuo YANAKA ◽  
Akira TAKAHASHI ◽  
Yoshinobu HOS H INO ◽  
Tomokazu SUZUKI ◽  
Makoto NISHIGAKI ◽  
...  
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
New Technique ◽  
Rock Fill ◽  
The Stability

Analyses for the stability of potash tailings piles

1993 ◽  
Vol 30 (3) ◽  
pp. 491-505 ◽  
Author(s):  
Delwyn G. Fredlund ◽  
Zai Ming Zhang ◽  
Karen Macdonald
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Field Studies ◽  
Equilibrium Analysis ◽  
Limit Equilibrium Analysis ◽  
Dissipation Model ◽  
The Stability

The stability of potash tailings piles is investigated using a pore-water pressure generation and dissipation model together with a limit equilibrium analysis. It is found that a shallow toe failure mode is generally the most applicable and that the stability may be influenced by pore-water pressure migration below the pile. It is suggested that field studies would be useful in evaluating stability in the toe region of the pile. Key words : potash tailings, slope stability, pore pressure dissipation, solutioning.

scholarly journals Effect of different parameters of heterogeneous dams on safety factor using the neural network. Case study: Marvan dam

2019 ◽  
Vol 32 (02) ◽  
pp. 126-138
Author(s):  
B. Beiranvand ◽  
A. Mohammadzade ◽  
M. Komasi
Keyword(s):  
Neural Network ◽  
Factor Of Safety ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Drainage System ◽  
Friction Angle ◽  
The Body ◽  
The Neural Network ◽  
The Cost

The drainage system is used to guide the flow of water in the earth dams. Construction of drainage in the dam body to collect and direct the drainage formed in the dam body to keep the slope dry and prevent the increase of pore water pressure in the body. One of the main goals of the designers is to find the minimum factor of safety and, consequently, reduce the cost of construction. In this study, the Marvak dam is modeled with the actual characteristics of the materials in the Geostudio software, and with the change in the dimensions of the drain, the material and the slope of the dam body, the minimum Factor of safety of the dam is obtained. In order to predict the minimum Factor of safety, a two-layer neural network has been used. With the training of the neural network based on the data obtained from heterogeneous dams, a minimum Factor of safety has been extracted for optimization of drainage. Finally, it was determined that the internal friction angle of the body material and the slope of the dam have the greatest effect on the dam factor of safety.

scholarly journals Influence of Layer Transition Zone on Rainfall-Induced Instability of Multilayered Slope

Lithosphere ◽  
2021 ◽  
Vol 2021 (Special 4) ◽  
Author(s):  
Zhi Dou ◽  
Yimin Liu ◽  
Xueyi Zhang ◽  
Yashan Wang ◽  
Zhou Chen ◽  
...  
Keyword(s):  
Hydraulic Conductivity ◽  
Transition Zone ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Layer Transition ◽  
Infiltration Process ◽  
Local Factor ◽  
The Stability ◽  
Different Thickness

Abstract Although numerous studies have been paid much attention to rainfall-induced instability of multilayered slopes, the interface between layers is generally considered to be “zero thickness”, and the layer transition zone between layers is neglected. In this study, the influence of the layer transition zone on the rainfall-induced instability of multilayered slope was investigated. A model was developed to simulate the rainfall infiltration process, the distribution of pore water pressure, and the stability of multilayered slope by coupling the unsaturated seepage model and the slope stability analysis method. Based on the analysis of the multilayered slopes with the different thickness ratios of the layer transition zone, a method for determining the critical thickness of the layer transition zone was proposed. The results showed that the layer transition zone had a significant influence on the stability of multilayered slope. It was found that the presence of the layer transition zone in the multilayered slope reduced the hydraulic conductivity of the slope and increased the rate of formation of transient saturated zone, which contributed to excess pore water pressure at the toe of the slope. The analysis of the local factor of safety (LFS) showed that when the thickness ratios of the layer transition zone were between 2.5% and 5%, the corresponding hydraulic conductivity of the slope decreased by 1%-2.5% and the maximum failure area of the slope during the rainfall was 25% of the slope. Our study highlighted the importance of the layer transition zone for the rainfall-induced instability of the multilayered slope.

scholarly journals Total and Effective Stresses in Backfilled Stopes during the Fill Placement on a Pervious Base for Barricade Design

Minerals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 38 ◽  
Author(s):  
Jian Zheng ◽  
Li Li ◽  
Yuchao Li
Keyword(s):  
Analytical Solution ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
The Self ◽  
Underground Mines ◽  
Filling Rate ◽  
Effective Stresses ◽  
Arching Effect ◽  
The Stability ◽  
Backfilled Stopes

Backfill is increasingly used in underground mines worldwide. Its successful application depends on the stability of the barricades built at the base of the stopes to hold the backfill in place, which in turn depends on the knowledge of the pore water pressure (PWP) and stresses during, or shortly after, the placement of the slurried backfill. Until now, self-weight consolidation is usually considered for the estimation of the PWP. There is no solution available to evaluate the total and effective stresses during, and shortly after, the filling operation. As excess PWP can simultaneously be generated (increased) and dissipated (decreased) during the backfilling operation, effective stresses can develop when the filling rate is low and/or hydraulic conductivity of the backfill is high. The arching effect has to be considered to evaluate the effective and total stresses in the backfilled stopes. In this paper, a pseudo-analytical solution is proposed to evaluate the effective and total stresses in backfilled stopes during the backfill deposition on a permeable base, by considering the self-weight consolidation and arching effect. The proposed solution is validated by numerical results obtained by Plaxis2D. A few sample applications of the proposed solution are shown.

Sign in / Sign up

Export Citation Format

Share Document