scholarly journals Evaluating Concrete Quality using Nondestructive In-situ Testing Methods

2019 ◽  
pp. 22-40
Author(s):  
Khalid Abdel Naser Abdel Rahim
Keyword(s):  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Initial Surface ◽  
In Situ Testing ◽  
Surface Absorption ◽  
Concrete Quality

This manuscript investigate the quality of concrete using non-destructive in-situ testing.The in-situ testing is a process by which different test are carried out such as rebound hammer, ultrasonic pulse veloc-ity, initial surface absorption test and fig air, to determine thein-situ strength, durability and deterioration, air permeability, concrete quality control andperformance. Additionally, the quality of concrete was researched using test methods with experimental results. Moreover, this research has found that (1) the increase in w/c ra-tioleads to a decrease in compressive strength and ultrasonic pulse velocity. Thus, lower w/cratio gives a bet-ter concrete strength in terms of quality, (2) the quicker the ultrasonic pulse travels through concrete indicates that the concrete is denser, therefore, better quality, (3) the lower initial surface absorption value indicates a better concrete with respect to porosity and (4) the w/c ratio plays an important role in the strength and per-meability of concrete.

scholarly journals The assessment of concrete quality by ultrasonic pulse velocity

2018 ◽  
Vol 12 (5) ◽  
pp. 20-27
Author(s):  
Van Viet Thien An
Keyword(s):  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Internal Defect ◽  
Internal Defects ◽  
Testing Method ◽  
Concrete Quality ◽  
Concrete Elements

In the present study, the uniformity and potential internal defects of concrete elements in situ were assessed by using Ultrasonic Pulse Velocity (UPV) testing method according to TCVN 9357:2012. Thirteen cross beams with dimension of 4.8 x 1.5 x 1.5 m3 were selected to measure the pulse velocity. Three cross beams were used to check potential internal defects in concrete and 10 cross beams were used to assess the uniformity of concrete in the elements. The results showed that there is no potential internal defect with size over 100 mm in three tested beams and concrete quality of all tested beams is good with the coefficient of variation (CV) of ultrasonic pulse velocity results of all tested points is lower than 2%. Keywords: concrete; homogeneity; internal defects; ultrasonic pulse velocity.

scholarly journals Effect of Improper Curing on the Properties of Normal Strength Concrete

2018 ◽  
Vol 8 (6) ◽  
pp. 3536-3540
Author(s):  
R. P. Memon ◽  
A. R. M. Sam ◽  
A. Z. Awang ◽  
U. I. Memon
Keyword(s):  
Cement Content ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Controlled Environment ◽  
Normal Strength Concrete ◽  
Normal Concrete ◽  
Normal Strength

In real applications, 28 days are regarded as proper curing time for concrete. There is a self-evident need to minimize the duration of curing days. For this purpose, this research investigates 1 to 7 days of curing and compares it with concrete cured for 28 days. Three grades of normal concrete strength grade 30, grade 35 and grade 40 were made. After curing, two exposure conditions were applied to the concrete, inside laboratory-controlled environment and outside environment. Results indicate that slump increases with cement content in DOE method at constant water content. The concrete density in all grades reduces when the concrete is subject to inside exposure in comparison with outside exposure. Water loss from concrete reduces with increase in curing days in all concrete grades. Compression strength of all concrete grades increases with increase in curing days. For the uniformity of concrete, ultrasonic pulse velocity indicated that with an increase in curing days, concrete becomes denser and a bit void. Results showed that an increase in curing days also improves the surface quality of concrete. The significance point noticed is that there was not much difference in the concrete properties between 7 days of curing and 28 days of curing in all grades.

scholarly journals Evaluation of Concrete Quality for Reinforced Concrete Frame Members Exposed to Natural Fires at Early Ages Using in situ Test Methods

2019 ◽  
Vol 13 (1) ◽  
pp. 201-209
Author(s):  
Muhammad I. Omer ◽  
Dilshad K. Jaf
Keyword(s):  
Reinforced Concrete ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Early Age ◽  
Concrete Frames ◽  
Natural Fire ◽  
Concrete Quality ◽  
Fire Accidents

Background: In recent years, numerous reinforced concrete buildings have been constructed in Iraq and some developing countries. Fire accidents occur in wooden formwork especially during the summer season due to problems associated with the construction procedure and on-site management. And fires can erupt during the construction stage of buildings. Introduction: Generally, if fire accidents occur in a wooden formwork, in these situations the concrete in the field is at an early age (i.e., “young”). The internal structure and chemical composition of early-age concrete are different from that of the carrier due to incomplete hydration at an early age. This study aimed to evaluate the strength of reinforced concrete frames at early ages when exposed to natural fire. The evaluation of existing buildings is an important issue that involves researchers and engineers in many countries. Methods: The experimental program consisted of constructing three full-scale reinforced concrete frames that are then exposed to natural fire. When the concrete age reaches three and five days by firing its formwork, the concrete quality of the structure was evaluated via ultrasonic pulse velocity as a nondestructive measurement. Core test was used as a destructive technique to implement a relationship between compressive strength and nondestructive measurements Results: The results showed that the frame exposed to natural fire early was generally more affected than the other frame, and its compressive strength was reduced close to 33%. The results also showed that the ultrasonic pulse velocity test for the structural elements was smaller than those of the core test Conclusion: It can be concluded that the current assessment methodology must be evaluated to provide practical suggestions that can enhance the reliability of assessing the in situ strength of existing concrete structures by nondestructive tests and cores.

scholarly journals In-situ examination of the concrete quality European standard approach

2018 ◽  
Vol 196 ◽  
pp. 02045
Author(s):  
Andrzej Moczko ◽  
Marta Moczko
Keyword(s):  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Velocity Measurements ◽  
European Standard ◽  
Pull Out ◽  
Standard Procedures ◽  
Concrete Quality ◽  
Proper Interpretation

The paper presents overview of European standard procedures related to determining concrete quality basing on the in-situ testing. Among other things following testing methods have been discussed: testing cored specimens, rebound measurements, “pull-out” method, “pull-off” method, ultrasonic pulse velocity measurements. Testing conditions, guidelines for calibration and crucial requirement for proper interpretation of the data obtained by means of rebound and ultrasonic measurements were shown. Independently “pull-out” and “pull-off” NDT methods have been introduced. Finally, the European procedures of assessment of in-situ concrete compressive strength in structures have been also presented.

scholarly journals In Situ Measurement of the Compressive Strength of Local Concrete: Correlation between Non-destructive and Destructive Tests

2020 ◽  
pp. 1-10
Author(s):  
Saïdou Bamogo ◽  
David Y. K. Toguyeni ◽  
Fati Zoma ◽  
Mohamed Yerbanga
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Compression Tests ◽  
Regression Methods ◽  
Tests And Measurements ◽  
Non Destructive

The method used to evaluate the quality of concrete in structures includes, among other things, compressive strength testing of specimens cast on site. This method has shortcomings due to the non-uniformity in their formulation processes of the concrete studied in laboratories and that of the structure on site and the tardiness in obtaining test results. This is why the development of reliable methods of non-destructive assessment of the compressive strength of concrete in situ is essential for a better performance assessment of structures.There are a multitude of non-destructive methods, but in this article, the ultrasonic pulse velocity (UPV) and the rebound hammer (RH) are the methods used as they are easy to get manipulate, accessible and permit fast access to results. Analyses using single and multiple linear regression methods have been carried out with the results from compression tests and measurements of pulse velocity and rebound indices carried out between February and April 2018 on over 90 specimen samples in total. This resulted in correlation equations for the in-situ estimation of the compressive strength of the concrete studied.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

scholarly journals Correlation between Uniaxial Compression Test and Ultrasonic Pulse Rate in Cement with Different Pozzolanic Additions

2021 ◽  
Vol 11 (9) ◽  
pp. 3747
Author(s):  
Leticia Presa ◽  
Jorge L. Costafreda ◽  
Domingo Alfonso Martín
Keyword(s):  
Compression Test ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Uniaxial Compression Test ◽  
Unconfined Compression Test ◽  
Pozzolanic Cement ◽  
The Relationship ◽  
Compression Resistance

This work aims to study the relationship between the compression resistance and velocity from ultrasonic pulses in samples of mortars with 25% of pozzolanic content. Pozzolanic cement is a low-priced sustainable material that can reduce costs and CO2 emissions that are produced in the manufacturing of cement from the calcination of calcium carbonate. Using ultrasonic pulse velocity (UPV) to estimate the compressive resistance of mortars with pozzolanic content reduces costs when evaluating the quality of structures built with this material since it is not required to perform an unconfined compression test. The objective of this study is to establish a correlation in order to estimate the compression resistance of this material from its ultrasonic pulse velocity. For this purpose, we studied a total of 16 cement samples, including those with additions of pozzolanic content with different compositions and a sample without any additions. The results obtained show the mentioned correlation, which establishes a basis for research with a higher number of samples to ascertain if it holds true at greater curing ages.

scholarly journals High Strength Nano Silica Based Concrete

2020 ◽  
Vol 9 (7) ◽  
pp. 1150-1155
Keyword(s):  
Electron Microscope ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hardened Concrete ◽  
Nano Silica ◽  
Nano Structure ◽  
Transmission Electron

There is a substantial curiosity in academia, the investment community and among manufacturers about the exhilarating opportunities offered by nano materials. Although a lot of applications for nanotechnology remain hypothetical, construction is one area where numerous ‘here and now’ applications have already emerged. While existing use is restricted, the market is likely to approach more than 500 million dollars within ten years. Concrete is most likely exceptional in the construction field, that it is the distinct material exclusive to business and hence, is the recipient of a reasonable quantity of research and development capital from the construction industry. SiO2 (Silica) usually is an integral part of concrete in the normal mix. On the other hand, one of the innovations made by the study of concrete at nano scale level is that particle stuffing in concrete can be enhanced by means of adding nano silica (NS), which results in the densification of the micro and nano structure of cementitious composite resulting in enhanced mechanical properties. In this research paper, the result of a thorough investigational analysis on the utilization of NS in addition to cement so that the strength and quality of concrete can improve has been achieved. The effect of various proportions of NS in concrete has been premeditated to evaluate the properties of NS based hardened concrete according to the standard concrete. The obtained outcomes after testing indicate that the addition of NS together with concrete has improved the mechanical behavior of concrete. The NS blended high strength concrete (HSC) shows a better compressive strength (CS) of 66.00 N/mm2 (MPa) after standard twenty eight days, which is an exceptional development over standard concrete. Each and every mixture containing NS in various proportions gave enhanced outcomes in comparison with the standard predictable concrete. RH (Rebound Hammer), UPV (Ultrasonic Pulse Velocity), SEM (Scanning Electron Microscope) and TEM (Transmission Electron Microscope) examinations further authenticate the above results.

Sign in / Sign up

Export Citation Format

Share Document