scholarly journals Carbonization Temperature Effect over Activated Carbon Porosity Derived from Industrial Processing Waste

2019 ◽  
Vol 2 (3) ◽  
pp. 1205-1209
Author(s):  
Hasan Sayğılı
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Waste Product ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Processing Waste ◽  
Industrial Processing

The influence of carbonization temperature (CT) on pore properties of the prepared activated carbon using lentil processing waste product (LWP) impregnated with potassium carbonate was studied. Activated carbons (ACs) were obtained by impregnation with 3:1 ratio (w/w) K2CO3/LWP under different carbonization temperatures at 600, 700, 800 and 900 oC for 1h. Activation at low temperature represented that micropores were developed first and then mesoporosity developed, enhanced up to 800 oC and then started to decrease due to possible shrinking of pores. The optimum temperature for LWP was found to be around 800 oC on the basis of total pore volume and the Brunauer-Emmett-Teller (BET) surface area. The optimum LWPAC sample was found with a CT of 800 oC, which gives the highest BET surface area and pore volume of 1875 m2/g and 0.995 cm3/g, respectively.

Experimental Research on the Preparation of Porous Activated Carbon from Orange Wastes

2009 ◽  
Vol 79-82 ◽  
pp. 1907-1910
Author(s):  
Zhi Gang Xie
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Average Pore ◽  
Impregnation Ratio ◽  
Heat Preservation

Porous activated carbon was prepared from orange wastes using zinc chloride as an activating agent by one-step carbonization method. Effects of impregnation ratio, carbonization temperature and heat preservation time on pore characteristics of activated carbon were studied. The porous structures of the orange wastes activated carbon were investigated by BET, D-R equations, BJH equations and Kelvin theory. The morphology was observed using transmission electron microscopy (TEM). The mesoporous activated carbon is gained when the impregnation ratio is 3:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has total pore volume 2.098 cm3/g, mesoporous pore volume 1.438 cm3/g, with a high BET surface area 1476m2/g. The pore distribution of the mesoporous activated carbon is very concentrative, with average pore diameter of 3.88nm. While, the high specific surface area activated carbon is gained when the impregnation ratio is 2:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has high BET surface area 1909 m2/g, while the total pore volume is only 1.448cm3/g and microporous pore volume is 0.889cm3/g, with average pore diameter of 2.29 nm.

Adsorption and Desorption Behavior of Herbicide Using Bio-Based Materials

2019 ◽  
Vol 62 (6) ◽  
pp. 1435-1445 ◽  
Author(s):  
Saravanan Ramiah Shanmugam ◽  
Sushil Adhikari ◽  
Hyungseok Nam ◽  
Vivek Patil
Keyword(s):  
Activated Carbon ◽  
Pore Volume ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Agricultural Runoff ◽  
Kraft Lignin ◽  
Douglas Fir ◽  
Bet Surface Area ◽  
Runoff Water ◽  
Sorption Ability

HighlightsGlyphosate sorption using bio-based adsorbents was investigated in this study.Biochars showed poor sorption of glyphosate in comparison to the activated carbons.Total pore volume of bio-based adsorbents played a key role in sorption of glyphosate.Abstract. This study examined the glyphosate sorption ability of different bio-based materials, including biochars and activated carbons synthesized from Douglas fir, kraft lignin, and mixed wood pellets. All the biochars showed poor sorption of glyphosate in comparison to the activated carbons derived from biochars and the commercial powdered activated carbon (PAC) investigated in this study. All the biochar-derived activated carbons produced in the laboratory showed comparable glyphosate sorption in comparison to PAC. The activated carbons synthesized from Douglas fir biomass showed the highest glyphosate sorption among the activated carbons investigated. Langmuir and Freundlich isotherms were used to describe the adsorption kinetics of glyphosate onto activated carbons. Adsorption capacity showed better correlation (R2 = 0.989) with the total pore volume in comparison to the Brunauer-Emmett-Teller (BET) surface area and microporosity. The results of batch desorption tests indicated that the biochar-derived activated carbons and PAC showed >60% glyphosate retention. The results of this study indicate that activated carbons derived from biochars produced with thermochemical conversion processes could effectively sorb herbicide such as glyphosate similarly to commercial activated carbon and could be used either as a replacement for PAC in water treatment plants or for on-site treatment of agricultural runoff water. Keywords: Adsorption, Desorption, Herbicides, Kraft lignin, Model isotherms, Pore volume.

scholarly journals Effect of Mesopore Development on Butane Working Capacity of Biomass-Derived Activated Carbon for Automobile Canister

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 673
Author(s):  
Byeong-Hoon Lee ◽  
Hye-Min Lee ◽  
Dong Chul Chung ◽  
Byung-Joo Kim
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Volume Fraction ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Working Capacity ◽  
Activation Time

Kenaf-derived activated carbons (AKC) were prepared by H3PO4 activation for automobile canisters. The microstructural properties of AKC were observed using Raman spectra and X-ray diffraction. The textural properties were studied using N2/77 K adsorption isotherms. Butane working capacity was determined according to the ASTM D5228. From the results, the specific surface area and total pore volume of the AKC was determined to be 1260–1810 m2/g and 0.68–2.77 cm3/g, respectively. As the activation time increased, the butane activity and retentivity of the AKC increased, and were observed to be from 32.34 to 58.81% and from 3.55 to 10.12%, respectively. The mesopore ratio of activated carbon increased with increasing activation time and was observed up to 78% at 973 K. This indicates that butane activity and retentivity could be a function not only of the specific surface area or total pore volume, but also of the mesopore volume fraction in the range of 2.8–3.8 nm and 5.5-6.5 nm of adsorbents, respectively. The AKC exhibit enhanced butane working capacity compared to commercial activated carbon with the high performance of butane working capacity due to its pore structure having a high mesopore ratio.

scholarly journals The effects of activation conditions on physical properties of activated carbon

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7640-7647
Author(s):  
Yan Luo ◽  
Kang Wang ◽  
Ling Fei
Keyword(s):  
Activated Carbon ◽  
Physical Properties ◽  
Surface Area ◽  
Pore Volume ◽  
Specific Volume ◽  
Activated Carbons ◽  
Weight Ratio ◽  
Total Pore Volume ◽  
High Porosity ◽  
Activation Conditions

Porous carbons with a high porosity were successfully produced from fast pyrolysis pine wood char via a thermochemical method in which KOH was used as chemical activator. The effects of various weight ratios of KOH to pyrolysis char (0.65:1, 0.7:1, 1.0:1, 1.35:1, and 1.7:1) on the physical properties of activated carbons were investigated. When the weight ratio of KOH to pyrolysis char was 1.35:1, the prepared activated carbon had the highest surface area of 1140 m2/g with a total pore volume of 0.71 cm3/g, a microporous surface area of 957 m2/g, and a microporous specific volume of 0.51 cm3/g. As the weight ratio of KOH to pyrolysis char increased from 0.65 to 1.35, the prepared activated carbon had increases in total surface area, total pore volume, microporous surface area, and specific volume of micropores. However, there was a reverse trend when the weight ratio of KOH to pyrolysis char was higher than 1.35. The use of nitrogen as a flow gas resulted in much more developed activated carbon than without nitrogen. The experiment results suggested that activated carbon with high surface area could be prepared from pyrolysis char by adjusting the activation conditions.

scholarly journals Preparation and Characterization of Activated Carbon from Poplar Sawdust by Chemical Activation: Comparison of Different Activating Agents and Carbonization Temperature

2018 ◽  
Vol 3 (11) ◽  
pp. 6-11 ◽  
Author(s):  
Funda Ateş ◽  
Öznur Özcan
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Experimental Studies ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Koh Activation ◽  
Chemical Agent ◽  
Poplar Sawdust

Activated carbons were prepared from poplar sawdust by chemical activation using ZnCl2, H3PO4 or KOH. The influence of activating agents, carbonization temperatures ranging from 500 ºC to 800 ºC, and mass ratio of chemical agent to precursor (1:1 and 2:1) on the porosity of activated carbons were studied. The properties of the carbons were characterized by adsorption/desorption of nitrogen to determine the BET areas, scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). It was determined that the surface morphology and textural characteristics of activated carbons vary depending on the carbonization temperature or chemical agent. Maximum surface areas were obtained at carbonization temperatures of 500, 700 and 800 ºC for H3PO4, KOH and ZnCl2 activation, respectively. The activated carbons prepared using ZnCl2 and H3PO4 activation had a higher BET surface area (nearly 1100 m2/g) than that of the KOH activation (761 m2/g). This study also presents a comparison of mechanisms of activating agents and carbonization temperature. As a result of the experimental studies, positive results were obtained, and the production of activated carbon with a high surface area was conducted. 

scholarly journals Effect of textural and chemical characteristics of activated carbons on phenol adsorption in aqueous solutions

2017 ◽  
Vol 19 (4) ◽  
pp. 87-93 ◽  
Author(s):  
Diana P. Vargas ◽  
Liliana Giraldo ◽  
Juan Carlos Moreno-Piraján
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Chemical Properties ◽  
Granular Activated Carbon ◽  
Bet Surface Area ◽  
Phenol Adsorption

Abstract The effect of textural and chemical properties such as: surface area, pore volume and chemical groups content of the granular activated carbon and monoliths on phenol adsorption in aqueous solutions was studied. Granular activated carbon and monolith samples were produced by chemical activation. They were characterized by using N2 adsorption at 77 K, CO2 adsorption at 273 K, Boehm Titrations and immersion calorimetry in phenol solutions. Microporous materials with different pore size distribution, surface area between 516 and 1685 m2 g−1 and pore volumes between 0.24 and 0.58 cm3 g−1 were obtained. Phenol adsorption capacity of the activated carbon materials increased with increasing BET surface area and pore volume, and is favored by their surface functional groups that act as electron donors. Phenol adsorption capacities are in ranged between 73.5 and 389.4 mg · g−1.

scholarly journals Preparation and characterization of activated carbons from different kinds of coal

2020 ◽  
pp. 25-31
Author(s):  
Batkhishig Damdin ◽  
Purevsuren Barnasan ◽  
Chung-Jun Lin ◽  
Batbileg Sanjaa ◽  
Ariunaa Alyeksandr
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Bet Surface Area ◽  
Water Steam ◽  
Initial Coal

Initial coal was purified in heavy liquid with a density 1.3 cm3 of ZnCl2 solution and purified coal was carbonized and the initial coal samples of each deposits were purified by pyrolysis. Thus, the yield of pyrolysis hard residue in the enriched sample was slightly higher than in the hard residue of initial coal. Therefore, pyrolysis hard residue of purified coal (carbonized sample) was activated at 800°C for 2 hours by preheated water steam. Activated carbons (ACs) and non-activated and non-carbonized coal from Baganuur, Ereen and Nariin Sukhait deposits were technically analyzed and their iodine number, BET surface area, pore volume and adsorption of methylene blue (MB) were determined. When these results were compared, these indicators increased 5-17 times in the Baganuur activated carbon (BN-AC), Ereen activated carbon (E-AC) and Nariin Sukhait activated carbon (NS-AC) as compared to inactivated coal.

Development and Characterization of Activated Carbons Derived from Lignocellulosic Material

2020 ◽  
Vol 988 ◽  
pp. 80-86
Author(s):  
Dewa Ngakan Ketut Putra Negara ◽  
Tjokorda Gde Tirta Nindhia ◽  
Lusiana ◽  
I. Made Astika ◽  
Cokorda Istri Putri Kusuma Kencanawati
Keyword(s):  
Activated Carbon ◽  
Pore Size ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
High Surface ◽  
Carbonization Temperature ◽  
Lignocellulosic Material ◽  
Activation Time ◽  
Average Pore

Activated carbon is a multipurpose material due to its unique properties such as high surface area and pore volume. The reduced carbon source from coal has led to the development of activated carbon from lignocellulosic material. However, there is limited literature reported the use of swat bamboo (Gigantocholoa verticillata) as an activated carbon precursor. In this research, swat bamboo has been converted to activated carbons under different carbonization temperatures of 550, 650, and 750OC and activation durations of 1.5 and 2 h. The results show that at activation time of 1.5 h, increasing carbonization temperature affecting the higher pore volume and surface area gained. The optimal characteristics of activated carbon were obtained at a carbonization temperature of 750OC and activation time of 1.5 h. This due to the activated carbon produced in this condition has the highest pore volume, surface area, and adsorption capacity of 0.138 cm3/g, 135.30 m2/g, and 95.776 cm3/g, respectively. Its average pore diameter was 2.053 nm with fix carbon of 75.26% and C of 76.79%. It has a monomodal pore size distribution with the highest adsorption of 0.056 cm3/g/nm occurred at a pore size of 1.516 nm.

scholarly journals An Eco-Friendly Process for Removal of Lead from Aqueous Solution

2017 ◽  
Vol 11 (5) ◽  
pp. 47 ◽  
Author(s):  
Heman A. Smail ◽  
Kafia M. Shareef ◽  
Zainab H. Ramli
Keyword(s):  
Heavy Metal ◽  
Oxalic Acid ◽  
Surface Area ◽  
Pore Volume ◽  
Metal Ion ◽  
Adsorption Equilibrium ◽  
Total Pore Volume ◽  
Heavy Metal Ion ◽  
Bet Surface Area ◽  
Barley Husk

The adsorption of lead (Pb II) ion on different types of synthesized zeolite was investigated. The BET surface area, total pore volume & average pore size distribution of these synthesized zeolites were determined by adsorption isotherms for N2, the surface area & total pore volume of their sources were found by adsorption isothermN2.The adsorption equilibrium was measured after 24h at room temperature (RT) & concentration 10mg.L-1 of Pb (II) was used. The adsorption of heavy metal Pb (II) on four different prepared zeolites (LTA from Montmorillonite clay, FAU(Y)-B.H (G2) from Barley husk, Mordenite (G1) from Chert rock, FAU(X)-S.C (G3) from shale clay & modified Shale clay by oxalic acid (N1) & sodium hydroxide (N2)), were compared with the adsorption of their sources by using static batch experimental method. The major factors affecting the heavy metal ion sorption on different synthesized zeolites & their sources were investigated. The adsorption equilibrium capacity (Qm) of Pb (II) ion for different synthesized zeolites ordered from (N1>N2>LTA>G3>G2>G1&for their sources ordered Shale clay >Montmorilonite> Barley husk>Chert rock. The atomic absorption spectrometry was used for analysis of lead heavy metal ion, the obtained results in this study showed that the different synthesized zeolites were efficient ion exchanges for removing heavy metal, in particular, the modified zeolite from shale clay by oxalic acid.

scholarly journals Activated Carbons from Thermoplastic Precursors and Their Energy Storage Applications

Nanomaterials ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 896 ◽  
Author(s):  
Hye-Min Lee ◽  
Kwan-Woo Kim ◽  
Young-Kwon Park ◽  
Kay-Hyeok An ◽  
Soo-Jin Park ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Specific Surface ◽  
Surface Area ◽  
Field Emission ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Cross Linking ◽  
Mesopore Volume

In this study, low-density polyethylene (LDPE)-derived activated carbons (PE-AC) were prepared as electrode materials for an electric double-layer capacitor (EDLC) by techniques of cross-linking, carbonization, and subsequent activation under various conditions. The surface morphologies and structural characteristics of the PE-AC were observed by field-emission scanning electron microscope, Cs-corrected field-emission transmission electron microscope, and X-ray diffraction analysis, respectively. The nitrogen adsorption isotherm-desorption characteristics were confirmed by Brunauer–Emmett–Teller, nonlocal density functional theory, and Barrett–Joyner–Halenda equations at 77 K. The results showed that the specific surface area and total pore volume of the activated samples increased with increasing the activation time. The specific surface area, the total pore volume, and mesopore volume of the PE-AC were found to be increased finally to 1600 m2/g, 0.86 cm3/g, and 0.3 cm3/g, respectively. The PE-AC also exhibited a high mesopore volume ratio of 35%. This mesopore-rich characteristic of the activated carbon from the LDPE is considered to be originated from the cross-linking density and crystallinity of precursor polymer. The high specific surface area and mesopore volume of the PE-AC led to their excellent performance as EDLC electrodes, including a specific capacitance of 112 F/g.

Sign in / Sign up

Export Citation Format

Share Document