Adsorption and Desorption Behavior of Herbicide Using Bio-Based Materials

2019 ◽  
Vol 62 (6) ◽  
pp. 1435-1445 ◽  
Author(s):  
Saravanan Ramiah Shanmugam ◽  
Sushil Adhikari ◽  
Hyungseok Nam ◽  
Vivek Patil
Keyword(s):  
Activated Carbon ◽  
Pore Volume ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Agricultural Runoff ◽  
Kraft Lignin ◽  
Douglas Fir ◽  
Bet Surface Area ◽  
Runoff Water ◽  
Sorption Ability

HighlightsGlyphosate sorption using bio-based adsorbents was investigated in this study.Biochars showed poor sorption of glyphosate in comparison to the activated carbons.Total pore volume of bio-based adsorbents played a key role in sorption of glyphosate.Abstract. This study examined the glyphosate sorption ability of different bio-based materials, including biochars and activated carbons synthesized from Douglas fir, kraft lignin, and mixed wood pellets. All the biochars showed poor sorption of glyphosate in comparison to the activated carbons derived from biochars and the commercial powdered activated carbon (PAC) investigated in this study. All the biochar-derived activated carbons produced in the laboratory showed comparable glyphosate sorption in comparison to PAC. The activated carbons synthesized from Douglas fir biomass showed the highest glyphosate sorption among the activated carbons investigated. Langmuir and Freundlich isotherms were used to describe the adsorption kinetics of glyphosate onto activated carbons. Adsorption capacity showed better correlation (R2 = 0.989) with the total pore volume in comparison to the Brunauer-Emmett-Teller (BET) surface area and microporosity. The results of batch desorption tests indicated that the biochar-derived activated carbons and PAC showed >60% glyphosate retention. The results of this study indicate that activated carbons derived from biochars produced with thermochemical conversion processes could effectively sorb herbicide such as glyphosate similarly to commercial activated carbon and could be used either as a replacement for PAC in water treatment plants or for on-site treatment of agricultural runoff water. Keywords: Adsorption, Desorption, Herbicides, Kraft lignin, Model isotherms, Pore volume.

scholarly journals Carbonization Temperature Effect over Activated Carbon Porosity Derived from Industrial Processing Waste

2019 ◽  
Vol 2 (3) ◽  
pp. 1205-1209
Author(s):  
Hasan Sayğılı
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Waste Product ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Processing Waste ◽  
Industrial Processing

The influence of carbonization temperature (CT) on pore properties of the prepared activated carbon using lentil processing waste product (LWP) impregnated with potassium carbonate was studied. Activated carbons (ACs) were obtained by impregnation with 3:1 ratio (w/w) K2CO3/LWP under different carbonization temperatures at 600, 700, 800 and 900 oC for 1h. Activation at low temperature represented that micropores were developed first and then mesoporosity developed, enhanced up to 800 oC and then started to decrease due to possible shrinking of pores. The optimum temperature for LWP was found to be around 800 oC on the basis of total pore volume and the Brunauer-Emmett-Teller (BET) surface area. The optimum LWPAC sample was found with a CT of 800 oC, which gives the highest BET surface area and pore volume of 1875 m2/g and 0.995 cm3/g, respectively.

scholarly journals Phenol adsorption on high microporous activated carbons prepared from oily sludge: equilibrium, kinetic and thermodynamic studies

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
N. Mojoudi ◽  
N. Mirghaffari ◽  
M. Soleimani ◽  
H. Shariatmadari ◽  
C. Belver ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Pore Volume ◽  
Activated Carbons ◽  
Ph Value ◽  
Chemical Activation ◽  
Bet Surface Area ◽  
Polluted Water ◽  
Oily Sludge ◽  
Maximum Adsorption Capacity ◽  
Adsorption Desorption

AbstractThe purpose of this study was the preparation, characterization and application of high-performance activated carbons (ACs) derived from oily sludge through chemical activation by KOH. The produced ACs were characterized using iodine number, N2 adsorption-desorption, Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The activated carbon prepared under optimum conditions showed a predominantly microporous structure with a BET surface area of 2263 m2 g−1, a total pore volume of 1.37 cm3 g−1 and a micro pore volume of 1.004 cm3 g−1. The kinetics and equilibrium adsorption data of phenol fitted well to the pseudo second order model (R2 = 0.99) and Freundlich isotherm (R2 = 0.99), respectively. The maximum adsorption capacity based on the Langmuir model (434 mg g−1) with a relatively fast adsorption rate (equilibrium time of 30 min) was achieved under an optimum pH value of 6.0. Thermodynamic parameters were negative and showed that adsorption of phenol onto the activated carbon was feasible, spontaneous and exothermic. Desorption of phenol from the adsorbent using 0.1 M NaOH was about 87.8% in the first adsorption/desorption cycle and did not decrease significantly after three cycles. Overall, the synthesized activated carbon from oily sludge could be a promising adsorbent for the removal of phenol from polluted water.

Experimental Research on the Preparation of Porous Activated Carbon from Orange Wastes

2009 ◽  
Vol 79-82 ◽  
pp. 1907-1910
Author(s):  
Zhi Gang Xie
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Average Pore ◽  
Impregnation Ratio ◽  
Heat Preservation

Porous activated carbon was prepared from orange wastes using zinc chloride as an activating agent by one-step carbonization method. Effects of impregnation ratio, carbonization temperature and heat preservation time on pore characteristics of activated carbon were studied. The porous structures of the orange wastes activated carbon were investigated by BET, D-R equations, BJH equations and Kelvin theory. The morphology was observed using transmission electron microscopy (TEM). The mesoporous activated carbon is gained when the impregnation ratio is 3:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has total pore volume 2.098 cm3/g, mesoporous pore volume 1.438 cm3/g, with a high BET surface area 1476m2/g. The pore distribution of the mesoporous activated carbon is very concentrative, with average pore diameter of 3.88nm. While, the high specific surface area activated carbon is gained when the impregnation ratio is 2:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has high BET surface area 1909 m2/g, while the total pore volume is only 1.448cm3/g and microporous pore volume is 0.889cm3/g, with average pore diameter of 2.29 nm.

scholarly journals Effect of Mesopore Development on Butane Working Capacity of Biomass-Derived Activated Carbon for Automobile Canister

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 673
Author(s):  
Byeong-Hoon Lee ◽  
Hye-Min Lee ◽  
Dong Chul Chung ◽  
Byung-Joo Kim
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Volume Fraction ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Working Capacity ◽  
Activation Time

Kenaf-derived activated carbons (AKC) were prepared by H3PO4 activation for automobile canisters. The microstructural properties of AKC were observed using Raman spectra and X-ray diffraction. The textural properties were studied using N2/77 K adsorption isotherms. Butane working capacity was determined according to the ASTM D5228. From the results, the specific surface area and total pore volume of the AKC was determined to be 1260–1810 m2/g and 0.68–2.77 cm3/g, respectively. As the activation time increased, the butane activity and retentivity of the AKC increased, and were observed to be from 32.34 to 58.81% and from 3.55 to 10.12%, respectively. The mesopore ratio of activated carbon increased with increasing activation time and was observed up to 78% at 973 K. This indicates that butane activity and retentivity could be a function not only of the specific surface area or total pore volume, but also of the mesopore volume fraction in the range of 2.8–3.8 nm and 5.5-6.5 nm of adsorbents, respectively. The AKC exhibit enhanced butane working capacity compared to commercial activated carbon with the high performance of butane working capacity due to its pore structure having a high mesopore ratio.

scholarly journals The effects of activation conditions on physical properties of activated carbon

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7640-7647
Author(s):  
Yan Luo ◽  
Kang Wang ◽  
Ling Fei
Keyword(s):  
Activated Carbon ◽  
Physical Properties ◽  
Surface Area ◽  
Pore Volume ◽  
Specific Volume ◽  
Activated Carbons ◽  
Weight Ratio ◽  
Total Pore Volume ◽  
High Porosity ◽  
Activation Conditions

Porous carbons with a high porosity were successfully produced from fast pyrolysis pine wood char via a thermochemical method in which KOH was used as chemical activator. The effects of various weight ratios of KOH to pyrolysis char (0.65:1, 0.7:1, 1.0:1, 1.35:1, and 1.7:1) on the physical properties of activated carbons were investigated. When the weight ratio of KOH to pyrolysis char was 1.35:1, the prepared activated carbon had the highest surface area of 1140 m2/g with a total pore volume of 0.71 cm3/g, a microporous surface area of 957 m2/g, and a microporous specific volume of 0.51 cm3/g. As the weight ratio of KOH to pyrolysis char increased from 0.65 to 1.35, the prepared activated carbon had increases in total surface area, total pore volume, microporous surface area, and specific volume of micropores. However, there was a reverse trend when the weight ratio of KOH to pyrolysis char was higher than 1.35. The use of nitrogen as a flow gas resulted in much more developed activated carbon than without nitrogen. The experiment results suggested that activated carbon with high surface area could be prepared from pyrolysis char by adjusting the activation conditions.

scholarly journals Preparation and characterization of bio-based activated carbon from fish scales

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 614-621
Author(s):  
Qingsong Ji ◽  
Haichao Li ◽  
Jingjing Zhang
Keyword(s):  
Activated Carbon ◽  
Functional Groups ◽  
Photoelectron Spectroscopy ◽  
Activated Carbons ◽  
Structural Characteristics ◽  
Total Pore Volume ◽  
Bet Surface Area ◽  
Fish Scales ◽  
Average Pore ◽  
Activation Temperature

The object of this study was to prepare activated carbons containing nitrogenous functional groups by a chemical method from nitrogen-containing raw materials. Fish (Ctenopharyngodon idellus) scales were impregnated with phosphoric acid (H3PO4) and activated at varied temperatures. The adsorption ability, structural characteristics, surface chemistry, and morphology of the activated carbons were characterized by methylene blue and iodine values, nitrogen adsorption, the Boehm method, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The total alkaline groups content of the activated carbon produced from fish scales was 0.4330 mmol/g, the total acidic groups was 1.68 mmol/g, the Brunauer–Emmett–Teller (BET) surface area was 501 cm2/g, and the total pore volume was 0.284 cm3/g. The average pore diameter was 1.94 nm under an activation temperature of 550 °C, an activation time of 1 h, and an impregnation ratio of 2. As a result of this study, nitrogenous functional groups that contained acid-base amphoteric adsorbent were produced.

scholarly journals Effect of textural and chemical characteristics of activated carbons on phenol adsorption in aqueous solutions

2017 ◽  
Vol 19 (4) ◽  
pp. 87-93 ◽  
Author(s):  
Diana P. Vargas ◽  
Liliana Giraldo ◽  
Juan Carlos Moreno-Piraján
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Chemical Properties ◽  
Granular Activated Carbon ◽  
Bet Surface Area ◽  
Phenol Adsorption

Abstract The effect of textural and chemical properties such as: surface area, pore volume and chemical groups content of the granular activated carbon and monoliths on phenol adsorption in aqueous solutions was studied. Granular activated carbon and monolith samples were produced by chemical activation. They were characterized by using N2 adsorption at 77 K, CO2 adsorption at 273 K, Boehm Titrations and immersion calorimetry in phenol solutions. Microporous materials with different pore size distribution, surface area between 516 and 1685 m2 g−1 and pore volumes between 0.24 and 0.58 cm3 g−1 were obtained. Phenol adsorption capacity of the activated carbon materials increased with increasing BET surface area and pore volume, and is favored by their surface functional groups that act as electron donors. Phenol adsorption capacities are in ranged between 73.5 and 389.4 mg · g−1.

scholarly journals Preparation and characterization of activated carbons from different kinds of coal

2020 ◽  
pp. 25-31
Author(s):  
Batkhishig Damdin ◽  
Purevsuren Barnasan ◽  
Chung-Jun Lin ◽  
Batbileg Sanjaa ◽  
Ariunaa Alyeksandr
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Bet Surface Area ◽  
Water Steam ◽  
Initial Coal

Initial coal was purified in heavy liquid with a density 1.3 cm3 of ZnCl2 solution and purified coal was carbonized and the initial coal samples of each deposits were purified by pyrolysis. Thus, the yield of pyrolysis hard residue in the enriched sample was slightly higher than in the hard residue of initial coal. Therefore, pyrolysis hard residue of purified coal (carbonized sample) was activated at 800°C for 2 hours by preheated water steam. Activated carbons (ACs) and non-activated and non-carbonized coal from Baganuur, Ereen and Nariin Sukhait deposits were technically analyzed and their iodine number, BET surface area, pore volume and adsorption of methylene blue (MB) were determined. When these results were compared, these indicators increased 5-17 times in the Baganuur activated carbon (BN-AC), Ereen activated carbon (E-AC) and Nariin Sukhait activated carbon (NS-AC) as compared to inactivated coal.

scholarly journals Preparation of High-Performance Activated Carbon from Coffee Grounds after Extraction of Bio-Oil

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 257
Author(s):  
Jie Ren ◽  
Nanwei Chen ◽  
Li Wan ◽  
Guojian Li ◽  
Tao Chen ◽  
...  
Keyword(s):  
Activated Carbon ◽  
High Performance ◽  
Average Pore Size ◽  
Total Pore Volume ◽  
Micropore Volume ◽  
Bet Surface Area ◽  
Average Pore ◽  
Activation Temperature ◽  
Coffee Grounds ◽  
Bio Oil

In this study, a new method for economical utilization of coffee grounds was developed and tested. The resulting materials were characterized by proximate and elemental analyses, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and N2 adsorption–desorption at 77 K. The experimental data show bio-oil yields reaching 42.3%. The optimal activated carbon was obtained under vacuum pyrolysis self-activation at an operating temperature of 450 °C, an activation temperature of 600 °C, an activation time of 30 min, and an impregnation ratio with phosphoric acid of 150 wt.%. Under these conditions, the yield of activated carbon reached 27.4% with a BET surface area of 1420 m2·g−1, an average pore size of 2.1 nm, a total pore volume of 0.747 cm3·g−1, and a t-Plot micropore volume of 0.428 cm3·g−1. In addition, the surface of activated carbon looked relatively rough, containing mesopores and micropores with large amounts of corrosion pits.

scholarly journals An Eco-Friendly Process for Removal of Lead from Aqueous Solution

2017 ◽  
Vol 11 (5) ◽  
pp. 47 ◽  
Author(s):  
Heman A. Smail ◽  
Kafia M. Shareef ◽  
Zainab H. Ramli
Keyword(s):  
Heavy Metal ◽  
Oxalic Acid ◽  
Surface Area ◽  
Pore Volume ◽  
Metal Ion ◽  
Adsorption Equilibrium ◽  
Total Pore Volume ◽  
Heavy Metal Ion ◽  
Bet Surface Area ◽  
Barley Husk

The adsorption of lead (Pb II) ion on different types of synthesized zeolite was investigated. The BET surface area, total pore volume & average pore size distribution of these synthesized zeolites were determined by adsorption isotherms for N2, the surface area & total pore volume of their sources were found by adsorption isothermN2.The adsorption equilibrium was measured after 24h at room temperature (RT) & concentration 10mg.L-1 of Pb (II) was used. The adsorption of heavy metal Pb (II) on four different prepared zeolites (LTA from Montmorillonite clay, FAU(Y)-B.H (G2) from Barley husk, Mordenite (G1) from Chert rock, FAU(X)-S.C (G3) from shale clay & modified Shale clay by oxalic acid (N1) & sodium hydroxide (N2)), were compared with the adsorption of their sources by using static batch experimental method. The major factors affecting the heavy metal ion sorption on different synthesized zeolites & their sources were investigated. The adsorption equilibrium capacity (Qm) of Pb (II) ion for different synthesized zeolites ordered from (N1>N2>LTA>G3>G2>G1&for their sources ordered Shale clay >Montmorilonite> Barley husk>Chert rock. The atomic absorption spectrometry was used for analysis of lead heavy metal ion, the obtained results in this study showed that the different synthesized zeolites were efficient ion exchanges for removing heavy metal, in particular, the modified zeolite from shale clay by oxalic acid.

Sign in / Sign up

Export Citation Format

Share Document