Effect of Mesopore Development on Butane Working Capacity of Biomass-Derived Activated Carbon for Automobile Canister

Kenaf-derived activated carbons (AKC) were prepared by H3PO4 activation for automobile canisters. The microstructural properties of AKC were observed using Raman spectra and X-ray diffraction. The textural properties were studied using N2/77 K adsorption isotherms. Butane working capacity was determined according to the ASTM D5228. From the results, the specific surface area and total pore volume of the AKC was determined to be 1260–1810 m2/g and 0.68–2.77 cm3/g, respectively. As the activation time increased, the butane activity and retentivity of the AKC increased, and were observed to be from 32.34 to 58.81% and from 3.55 to 10.12%, respectively. The mesopore ratio of activated carbon increased with increasing activation time and was observed up to 78% at 973 K. This indicates that butane activity and retentivity could be a function not only of the specific surface area or total pore volume, but also of the mesopore volume fraction in the range of 2.8–3.8 nm and 5.5-6.5 nm of adsorbents, respectively. The AKC exhibit enhanced butane working capacity compared to commercial activated carbon with the high performance of butane working capacity due to its pore structure having a high mesopore ratio.

Download Full-text

Pitch-Derived Activated Carbon Fibers for Emission Control of Low-Concentration Hydrocarbon

Nanomaterials ◽

10.3390/nano9091313 ◽

2019 ◽

Vol 9 (9) ◽

pp. 1313 ◽

Cited By ~ 3

Author(s):

Hye-Min Lee ◽

Byeong-Hoon Lee ◽

Soo-Jin Park ◽

Kay-Hyeok An ◽

Byung-Joo Kim

Keyword(s):

Activated Carbon ◽

Specific Surface ◽

Surface Area ◽

Specific Surface Area ◽

Carbon Fibers ◽

Pore Volume ◽

Volume Fraction ◽

Structural Characteristics ◽

Total Pore Volume ◽

Activated Carbon Fibers

The unburned hydrocarbon (HC) emissions of automobiles are subject to strong regulations because they are known to be converted into fine dust, ozone, and photochemical smog. Pitch-based activated carbon fibers (ACF) prepared by steam activation can be a good solution for HC removal. The structural characteristics of ACF were observed using X-ray diffraction. The pore characteristics were investigated using N2/77K adsorption isotherms. The butane working capacity (BWC) was determined according to ASTM D5228. From the results, the specific surface area and total pore volume of the ACF were determined to be 840–2630 m2/g and 0.33–1.34 cm3/g, respectively. The butane activity and butane retentivity of the ACF increased with increasing activation time and were observed to range between 15.78–57.33% and 4.19–11.47%, respectively. This indicates that n-butane adsorption capacity could be a function not only of the specific surface area or total pore volume but also of the sub-mesopore volume fraction in the range of 2.0–2.5 nm of adsorbents. The ACF exhibit enhanced BWC, and especially adsorption velocity, compared to commercial products (granules and pellets), with lower concentrations of n-butane due to a uniformly well-developed pore structure open directly to the outer surface.

Download Full-text

Activated Carbons from Thermoplastic Precursors and Their Energy Storage Applications

Nanomaterials ◽

10.3390/nano9060896 ◽

2019 ◽

Vol 9 (6) ◽

pp. 896 ◽

Cited By ~ 2

Author(s):

Hye-Min Lee ◽

Kwan-Woo Kim ◽

Young-Kwon Park ◽

Kay-Hyeok An ◽

Soo-Jin Park ◽

...

Keyword(s):

Electron Microscope ◽

Specific Surface ◽

Surface Area ◽

Field Emission ◽

Specific Surface Area ◽

Pore Volume ◽

Activated Carbons ◽

Total Pore Volume ◽

Cross Linking ◽

Mesopore Volume

In this study, low-density polyethylene (LDPE)-derived activated carbons (PE-AC) were prepared as electrode materials for an electric double-layer capacitor (EDLC) by techniques of cross-linking, carbonization, and subsequent activation under various conditions. The surface morphologies and structural characteristics of the PE-AC were observed by field-emission scanning electron microscope, Cs-corrected field-emission transmission electron microscope, and X-ray diffraction analysis, respectively. The nitrogen adsorption isotherm-desorption characteristics were confirmed by Brunauer–Emmett–Teller, nonlocal density functional theory, and Barrett–Joyner–Halenda equations at 77 K. The results showed that the specific surface area and total pore volume of the activated samples increased with increasing the activation time. The specific surface area, the total pore volume, and mesopore volume of the PE-AC were found to be increased finally to 1600 m2/g, 0.86 cm3/g, and 0.3 cm3/g, respectively. The PE-AC also exhibited a high mesopore volume ratio of 35%. This mesopore-rich characteristic of the activated carbon from the LDPE is considered to be originated from the cross-linking density and crystallinity of precursor polymer. The high specific surface area and mesopore volume of the PE-AC led to their excellent performance as EDLC electrodes, including a specific capacitance of 112 F/g.

Download Full-text

Preparation of Activated Carbons from Lignite for Electrochemical Capacitors by Microwave and Electrical Furnace Heating

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.194-196.2472 ◽

2011 ◽

Vol 194-196 ◽

pp. 2472-2479 ◽

Cited By ~ 5

Author(s):

Bao Lin Xing ◽

Chuan Xiang Zhang ◽

Lun Jian Chen ◽

Guang Xu Huang

Keyword(s):

Specific Surface ◽

Specific Capacitance ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Activated Carbons ◽

Electrochemical Capacitors ◽

Weight Ratio ◽

Total Pore Volume ◽

Electrochemical Performances

Activated carbons (ACs) were prepared from lignite by microwave (MW) and electrical furnace (EF) heating with KOH as activation agent. In order to compare pore structures and electrochemical performances of ACs prepared by both heating methods, the ACs were characterized by N2 adsorption at 77K, X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical performances of Electrochemical capacitors (ECs) with ACs as electrodes in 3mol/L KOH electrolyte were evaluated by constant current charge-discharge, cyclic voltammetry and electrochemical impedance spectroscopy. The results show that the pore structures of ACs prepared by MW and EF heating significantly enhance when the weight ratio of KOH to coal increases from 2 to 4. The BET specific surface area, total pore volume, the ratio of mesopore and average pore diameter of ACs prepared by MW heating (denoted as AC-MW4) reaches 2094m2/g, 1.193cm3/g, 53.6%, 2.28nm when the weight ratio of KOH to coal is 4, and ACs prepared by EF heating (denoted as AC-EF4) reaches 2580m2/g, 1.683cm3/g, 67.3%, 2.61nm. The ECs with AC-MW4 and AC-EF4 as electrodes present a high specific capacitance of 348F/g and 377F/g at a current density of 50mA/g, and still remain 325F/g and 350F/g after 500 cycles, respectively. Although the specific surface area, total pore volume and specific capacitance of ACs prepared by MW heating are slightly lower than EF heating, taking into account the heating time in the activation process, ACs prepared by EF heating needs approximate 140min, while MW heating only needs 10min, which have demonstrated that microwave heating technology is a promising and efficient technique to prepare ACs.

Download Full-text

Optimization of Experimental Conditions for the Preparation of High Specific Surface Area Bamboo-Based Activated Carbon

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.1090.154 ◽

2015 ◽

Vol 1090 ◽

pp. 154-159

Author(s):

Sheng Zhou Zhang ◽

Hong Ying Xia ◽

Li Bo Zhang ◽

Jin Hui Peng ◽

Jian Wu ◽

...

Keyword(s):

Activated Carbon ◽

Specific Surface ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Total Pore Volume ◽

High Specific Surface Area ◽

Raw Material ◽

Experimental Conditions ◽

Average Pore

Bamboo as the raw material is carbonized to prepare high specific surface area activated carbon by microwave heating under nitrogen atmosphere in our present work. Influences of activation agents on the preparation of activated carbon are studied. The results show that activation agents have a significant influence on the preparation of activated carbon. Under the heating time of 15 min, the adsorption capacity of the activated carbon prepared utilizing KOH as activation agent is the best. When the KOH/C ratio is 4, the iodine number and yield of activated carbon are 2298 mg/g and 39.82%, respectively. The BET specific surface area, total pore volume and average pore diameter of activated carbon are 3441 m2/g, 2.093 ml/g and 2.434 nm, respectively. The micropore volume of 1.304 ml/g is 62.30% of total pore volume, indicating that the activated carbon is microporous activated carbon.

Download Full-text

Pore Structure Regulation and Electrochemical Performance Characterization of Activated Carbon for Supercapacitors

Frontiers in Energy Research ◽

10.3389/fenrg.2021.680761 ◽

2021 ◽

Vol 9 ◽

Author(s):

Shijie Li ◽

Tao Xing ◽

Yilin Wang ◽

Pengwei Lu ◽

Weixue Kong ◽

...

Keyword(s):

Activated Carbon ◽

Specific Surface ◽

Pore Structure ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Activation Time ◽

Activation Temperature ◽

Specific Pore Volume ◽

Impregnation Time

In order to achieve the purpose of regulating the pore structure characteristics of activated carbon by adjusting the experimental parameters, the effects of carbonization temperature, carbonization time, pre-activation temperature, pre-activation time and impregnation time on the pore structure of sargassum-based activated carbon (SAC) are studied by orthogonal experiment. The gravimetric capacitance of SAC and the relationship between the gravimetric capacitance and specific surface area are also studied. The results show that the SACs prepared at all experimental conditions have developed pore structure and huge specific surface area, reaching 3,122 m2/g. The pore size of SAC is almost all within 6 nm, in which the micropores are mainly concentrated in 0.4–0.8 nm, the mesopores are mainly concentrated in 2–4 nm, and the number of micropores is significantly higher than that of mesopores. During the preparation of SAC, the effect of carbonization temperature on the specific surface area and specific pore volume of SAC is very significant. The effect of carbonization time on the specific surface area of SAC is significant, but the effect on specific pore volume can be ignored. The effects of pre-activation temperature, pre-activation time, and impregnation time on specific surface area and specific pore volume of SAC can be ignored. In addition, SACs show good gravimetric capacitance performance as electrode material for supercapacitors, which can significantly increase the capacitance of supercapacitors and thus broaden their applications. The gravimetric capacitance and specific surface area of SACs show a good linear relationship when the activated carbons have similar material properties and pore size distribution.

Download Full-text

Properties of activated carbon regulated by rapid cooling treatment after pyrolysis

BioResources ◽

10.15376/biores.14.4.7935-7942 ◽

2019 ◽

Vol 14 (4) ◽

pp. 7935-7942

Author(s):

Bing Wang ◽

Huiyuan Chen ◽

Yonggang Li ◽

Hongyu Si ◽

Haomin Wei ◽

...

Keyword(s):

Activated Carbon ◽

Specific Surface ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Activated Carbons ◽

Raw Materials ◽

Average Pore Size ◽

Process Conditions ◽

Rapid Cooling

Effects of rapid cooling following pyrolysis were studied relative to the properties of activated carbon using different biomass as the raw materials. Coconut shell-based activated carbon (CSAC), bamboo-based activated carbon (BAC), and straw-based activated carbon (WSAC) were activated via high temperature and subsequently rapidly cooled to below minus 150 °C. The results showed that rapid cooling effectively increased the specific surface area, pore volume, and yield of activated carbons. Compared to natural cooling, rapid cooling increased the specific surface area of CSAC from 1076 m2/g to 1484 m2/g, increased the pore volume from 1.46 mL/g to 1.57 mL/g, decreased the average pore size from 2.25 nm to 2.13 nm, and increased the yield from 27.1% to 31.5%. The variation of the properties of activated carbon after rapid cooling using different raw materials and process conditions were studied using orthogonal experiments.

Download Full-text

Nanometer Pore Structure Characterization of Taiyuan Formation Shale in the Lin-Xing Area Based on Nitrogen Adsorption Experiments

Minerals ◽

10.3390/min11030298 ◽

2021 ◽

Vol 11 (3) ◽

pp. 298

Author(s):

Chenlong Ding ◽

Jinxian He ◽

Hongchen Wu ◽

Xiaoli Zhang

Keyword(s):

Specific Surface ◽

Pore Structure ◽

Surface Area ◽

Specific Surface Area ◽

Shale Gas ◽

Pore Volume ◽

Ordos Basin ◽

Total Pore Volume ◽

Nitrogen Adsorption ◽

Taiyuan Formation

Ordos Basin is an important continental shale gas exploration site in China. The micropore structure of the shale reservoir is of great importance for shale gas evaluation. The Taiyuan Formation of the lower Permian is the main exploration interval for this area. To examine the nanometer pore structures in the Taiyuan Formation shale reservoirs in the Lin-Xing area, Northern Shaanxi, the microscopic pore structure characteristics were analyzed via nitrogen adsorption experiments. The pore structure parameters, such as specific surface area, pore volume, and aperture distribution, of shale were calculated; the significance of the pore structure for shale gas storage was analyzed; and the main controlling factors of pore development were assessed. The results indicated the surface area and hole volume of the shale sample to be 0.141–2.188 m2/g and 0.001398–0.008718 cm3/g, respectively. According to the IUPAC (International Union of Pure and Applied Chemistry) classification, mesopores and macropores were dominant in the pore structure, with the presence of a certain number of micropores. The adsorption curves were similar to the standard IV (a)-type isotherm line, and the hysteresis loop type was mainly similar to H3 and H4 types, indicating that most pores are dominated by open type pores, such as parallel plate-shaped pores and wedge-shaped slit pores. The micropores and mesopores provide the vast majority of the specific surface area, functioning as the main area for the adsorption of gas in the shale. The mesopores and macropores provide the vast majority of the pore volume, functioning as the main storage areas for the gas in the shale. Total organic carbon had no notable linear correlation with the total pore volume and the specific surface area. Vitrinite reflectance (Ro) had no notable correlation with the specific surface area, but did have a low “U” curve correlation with the total pore volume. There was no relationship between the quartz content and specific surface area and total pore volume. In addition, there was no notable correlation between the clay mineral content and total specific surface area and total pore volume.

Download Full-text

Study of the Porous Structure and High Adsorption Capacity of Biomass-Based Activated Carbon Prepared from Aspen Wood by Ferric Nitrate III Activation

Journal of Biobased Materials and Bioenergy ◽

10.1166/jbmb.2021.2047 ◽

2021 ◽

Vol 15 (2) ◽

pp. 131-144

Author(s):

Chunjiang Jin ◽

Huimin Chen ◽

Luyuan Wang ◽

Xingxing Cheng ◽

Donghai An ◽

...

Keyword(s):

Activated Carbon ◽

Specific Surface ◽

Adsorption Capacity ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Mass Ratio ◽

Aspen Wood ◽

Surface Functional Groups ◽

Wood Sawdust

In this study, aspen wood sawdust was used as the raw material, and Fe(NO3)3 and CO2 were used as activators. Activated carbon powder (ACP) was produced by the one-step physicochemical activation method in an open vacuum tube furnace. The effects of different mass ratios of Fe(NO3)3 and aspen wood sawdust on the pore structure of ACP were examined under single-variable experimental conditions. The mass ratio was 0–0.4. The detailed characteristics of ACP were examined by nitrogen adsorption, scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The adsorption capacity of ACP was established by simulating volatile organic compounds (VOCs) using ethyl acetate. The results showed that ACP has a good nanostructure with a large pore volume, specific surface area, and surface functional groups. The pore volume and specific surface area of Fe-AC-0.3 were 0.26 cm3/g and 455.36 m2/g, respectively. The activator played an important role in the formation of the pore structure and morphology of ACP. When the mass ratio was 0–0.3, the porosity increased linearly, but when it was higher than 0.3, the porosity decreased. For example, the pore volume and specific surface area of Fe-AC-0.4 reached 0.24 cm3/g and 430.87 m2/g, respectively. ACP presented good VOC adsorption performance. The Fe-AC-0.3 sample, which contained the most micropore structures, presented the best adsorption capacity for ethyl acetate at 712.58 mg/g. Under the action of the specific reaction products nitrogen dioxide (NO2) and oxygen, the surface of modified ACP samples showed different rich C/O/N surface functional groups, including C-H, C=C, C=O, C-O-C, and C-N.

Download Full-text

Structural and fractal characterization of adsorption pores of middle–high rank coal reservoirs in western Yunnan and eastern Guizhou: An experimental study of coals from the Panguan syncline and Laochang anticline

Energy Exploration & Exploitation ◽

10.1177/0144598718790319 ◽

2018 ◽

Vol 37 (1) ◽

pp. 251-272 ◽

Cited By ~ 9

Author(s):

Junjian Zhang ◽

Chongtao Wei ◽

Gaoyuan Yan ◽

Guanwen Lu

Keyword(s):

Specific Surface ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Pore Diameter ◽

Structural Parameters ◽

Total Pore Volume ◽

Type A ◽

Type B ◽

Type C

To better understand the structural characteristic of adsorption pores (pore diameter < 100 nm) of coal reservoirs around the coalbed methane production areas of western Yunnan and eastern Guizhou, we analyzed the structural and fractal characteristics of pore size range of 0.40–2.0 nm and 2–100 nm in middle–high rank coals ( Ro,max = 0.93–3.20%) by combining low-temperature N2/CO2 adsorption tests and surface/volume fractal theory. The results show that the coal reservoirs can be divided into three categories: type A ( Ro,max < 2.15%), type B (2.15% < Ro,max <2.50%), and type C ( Ro,max > 2.15%). The structural parameters of pores in the range from 2 to 100 nm are influenced by the degree of coal metamorphism and the compositional parameters (e.g., ash and volatile matter). The dominant diameters of the specific surface areas are 10–50 nm, 2–50 nm, and 2–10 nm, respectively. The pores in the range from <2 nm provide the largest proportion of total specific surface area (97.22%–99.96%) of the coal reservoir, and the CO2-specific surface area and CO2-total pore volume relationships show a positive linear correlation. The metamorphic degree has a much greater control on the pores (pore diameter less than 2 nm) structural parameters than those of the pore diameter ranges from 2 to 100 nm. Dv1 and Dv2 can characterize the structure of 2–100 nm adsorption pores, and Dv1 (volume heterogeneity) has a positive correlation with the pore structural parameters such as N2-specific surface area and N2-total pore volume. This parameter can be used to characterize volume heterogeneity of 2–10 nm pores. Dv2 (surface heterogeneity) showed type A > type B > type C and was mainly affected by the metamorphism degree. Ds2 can be used to characterize the pore surface heterogeneity of micropores in the range of 0.62–1.50 nm. This parameter has a good correlation with the pore parameters (CO2-total pore volume, CO2-specific surface area, and average pore size) and is expressed as type C < type B < type A. In conclusion, the heterogeneity of the micropores is less than that of the meso- and macropores (2–100 nm). Dv1, Dv2, and Ds2 can be used as effective parameters to characterize the pore structure of adsorption pores. This result can provide a theoretical basis for studying the pore structure compatibility of coal reservoirs in the region.

Download Full-text

The Influence of Sinterng Temperature on the Phase, Microstructure and Textual Properties of Hollow Hydroxyapatite Microspheres

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.239-242.2274 ◽

2011 ◽

Vol 239-242 ◽

pp. 2274-2279 ◽

Cited By ~ 1

Author(s):

Ying Chun Wang ◽

Wen Hai Huang ◽

Ai Hua Yao ◽

De Ping Wang

Keyword(s):

Specific Surface ◽

Pore Size ◽

Surface Area ◽

Specific Surface Area ◽

Pore Volume ◽

Sintering Temperature ◽

Total Pore Volume ◽

Precipitation Method ◽

Simple Method ◽

Air Atmosphere

A simple method to prepare hollow hydroxyapatite (HAP) microspheres with mespores on the surfaces is performed using a precipitation method assisted with Li2O-CaO-B2O3(LCB) glass fabrication process. This research is concerned with the effect of sintering temperature on the microstructure evolution, phase purity, surface morphology, specific surface area, and porosity after sintering process. The microspheres were sintered in air atmosphere at temperatures ranging from 500 to 900 °C. The starting hollow HAP microspheres and the sintered specimens were characterized by scanning electron microscope, X-ray diffractometer, specific surface area analyzer, and Hg porosimetry, respectively. The as-prepared microspheres consisted of calcium deficient hydroxyapatite. The results showed that the as-prepared hollow HAP microspheres had the highest specific surface areas, and the biggest total pore volume. The pore size distribution of the as-prepared hollow HAP microspheres were mainly the mesopores in the range of 2～40 nm. The specific surface area and total pore volume of hollow HAP microspheres decreased with increasing sintering temperature. Whereas the mean pore size increased with increasing sintering temperature. It showed that at 700°C, Ca-dHAP decomposes into a biphasic mixture of HAP and β-calcium phosphate(TCP).

Download Full-text