scholarly journals An Aerodynamic Design Method to Improve the High-Speed Performance of a Low-Aspect-Ratio Tailless Aircraft

2021 ◽  
Vol 11 (4) ◽  
pp. 1555
Author(s):  
Zhongyuan Liu ◽  
Lie Luo ◽  
Binqian Zhang
Keyword(s):  
Aspect Ratio ◽  
High Speed ◽  
Design Method ◽  
Aerodynamic Performance ◽  
Pitching Moment ◽  
Aerodynamic Design ◽  
Linear Superposition ◽  
Low Aspect Ratio ◽  
Drag Ratio ◽  
Lift To Drag Ratio

This paper puts forward an aerodynamic design method to improve the high-speed aerodynamic performance of an aircraft with low-aspect-ratio tailless configuration. The method can ameliorate the longitudinal moment characteristics of the configuration by designing and collocating the key section airfoils with the constrains of fixed parameters of planform shape and capacity. Firstly, the effect of twisting the wing, fore-loading and aft-reflexing key section airfoils on the high-speed aerodynamic performance of the configuration is evaluated by high-fidelity numerical methods, and quantified by defining trimming efficiency factors. Then, a linear superposition formula is obtained by analyzing the effect rule of trimming efficiency factor, and based on the formula the design and collocation methods of key section airfoils are achieved. According to the methods, a trimmed configuration is obtained. The results of computational fluid dynamics (CFD) and wind tunnel tests show that the trimmed configuration has smaller zero-lift pitching moment and higher available lift-to-drag ratio than the initial configuration at cruise, besides the trimmed configuration achieves the design principle raised for tailless configuration, which can be described as the zero-pitching moment, cruising design lift coefficient, and maximum lift-to-drag ratio are coincident. In addition, at off-design conditions, the trimmed configuration shows favorable drag divergence characteristics, satisfactory aerodynamic characteristics at medium-altitude maneuvering condition, and good stall and pitching-moment performance at low speed state.

Research on Improved Method of Wind Turbine Airfoil S834 Based on Noise and Aerodynamic Performance

2015 ◽  
Vol 744-746 ◽  
pp. 253-258 ◽  
Author(s):  
Ya Qiong Chen ◽  
Yue Fa Fang
Keyword(s):  
Wind Turbine ◽  
Optimization Design ◽  
Design Method ◽  
Aerodynamic Performance ◽  
Parametric Modeling ◽  
Multi Objective ◽  
Wind Turbine Airfoil ◽  
Drag Ratio ◽  
Operating Points ◽  
Lift To Drag Ratio

In this paper, aerodynamic performance and noise of the wind turbine airfoil are the optimization design goal and based on this, the optimization design method with multi-operating points and multi-objective of the airfoils is built. The Bezier curve is used in parametric modeling of the contour of the airfoil and the general equation for control points is deduced form the discrete points coordinates of the airfoil. The weigh distribution schemes for multi-objective and multi-operating points are integrated designed by treating the NREL S834 airfoil as the initial airfoils. The results show that the lift-to-drag ratio of the optimized airfoils has a improvement around the designed operating angle and the overall noise has a reduction compared with the initial airfoils, which means that the optimized airfoils get a better aerodynamic and acoustic performance.

Aerodynamic performance improvement of a canard control missile

2017 ◽  
Vol 89 (6) ◽  
pp. 871-878 ◽  
Author(s):  
M. Tahani ◽  
M. Masdari ◽  
M. Kazemi
Keyword(s):  
Aspect Ratio ◽  
Drag Coefficient ◽  
Cross Section ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Slender Body Theory ◽  
Content Type ◽  
Drag Ratio ◽  
Body Theory ◽  
Lift To Drag Ratio

Purpose This paper aims to analyze the influence of the changings in geometrical parameters on the aerodynamic performance of the control canard projectiles. Design/methodology/approach Because of the mentioned point, the range of projectiles increment has a considerable importance, and the design algorithm of a control canard projectile was first written. Then, were studied the effects of canard geometric parameters such as aspect ratio, taper ratio and deflectable nose on lift to drag coefficient ratio, static margin based on the slender body theory and cross section flow. Findings The code results show that aspect ratio increment, results in an increase in lift-to-drag ratio of the missile, but increase in canard taper ratio results in increasing of lift-to-drag ratio at 1° angle of attack, while during increasing the canard taper ratio up to 0.67 at 4° angle of attack, lift to drag first reaches to maximum and then decreases. Also, static margin decreases with canard taper ratio and aspect ratio increment. The developed results for this type of missile were compared with same experimental and computational fluid dynamic (CFD) results and appreciated agreement with other results at angles of attack between 0° and 6°. Practical implications To design a control canard missile, the effect of each geometric parameter of canard needs to be estimated. For this purpose, the suitable algorithm is used. In this paper, the effects of canard geometric parameters, such as aspect ratio, taper ratio and deflectable nose on lift-to-drag coefficient ratio and static margin, were studied with help of the slender body theory and cross-section flow. Originality/value The contribution of this paper is to predict the aerodynamic characteristics for the control canard missile. In this study, the effect of the design parameter on aerodynamic characteristics can be estimated, and the effect of geometrical characteristics has been analyzed with a suitable algorithm. Also, the best lift-to-drag coefficient for the NASA Tandem Control Missile at Mach 1.75 was selected at various angles of attack. The developed results for this type of missile were compared with same experimental and CFD results.

The aerodynamic optimisation of a low-Reynolds paper plane with adjoint method

2020 ◽  
pp. 1-15
Author(s):  
Y. Zhang ◽  
X. Zhang ◽  
G. Chen
Keyword(s):  
Adjoint Method ◽  
Low Cost ◽  
Aerodynamic Performance ◽  
Discrete Adjoint ◽  
Design Variables ◽  
Limited Variation ◽  
Aerial Vehicle ◽  
Paper Plane ◽  
Drag Ratio ◽  
Lift To Drag Ratio

ABSTRACT The aerodynamic performance of a deployable and low-cost unmanned aerial vehicle (UAV) is investigated and improved in present work. The parameters of configuration, such as airfoil and winglet, are determined via an optimising process based on a discrete adjoint method. The optimised target is locked on an increasing lift-to-drag ratio with a limited variation of pitching moments. The separation that will lead to a stall is delayed after optimisation. Up to 128 design variables are used by the optimised solver to give enough flexibility of the geometrical transformation. As much as 20% enhancement of lift-to-drag ratio is gained at the cruise angle-of-attack, that is, a significant improvement in the lift-to-drag ratio adhering to the preferred configuration is obtained with increasing lift and decreasing drag coefficients, essentially entailing an improved aerodynamic performance.

Simulation of Three-Dimensional Viscous Flow Within a Multistage Turbine

1990 ◽  
Vol 112 (3) ◽  
pp. 370-376 ◽  
Author(s):  
J. J. Adamczyk ◽  
M. L. Celestina ◽  
T. A. Beach ◽  
M. Barnett
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Three Dimensional ◽  
Equation System ◽  
Aerodynamic Performance ◽  
Experimental Measurements ◽  
Low Aspect Ratio ◽  
Blade Row ◽  
Multistage Turbine ◽  
Secondary Flow Field

This work outlines a procedure for simulating the flow field within multistage turbomachinery, which includes the effects of unsteadiness, compressibility, and viscosity. The associated modeling equations are the average passage equation system, which governs the time-averaged flow field within a typical passage of a blade row embedded within a multistage configuration. The results from a simulation of a low aspect ratio stage and one-half turbine will be presented and compared with experimental measurements. It will be shown that the secondary flow field generated by the rotor causes the aerodynamic performance of the downstream vane to be significantly different from that of an isolated blade row.

scholarly journals High Speed Microactuators for Low Aspect Ratio High Speed Micro Aircraft Surfaces

Actuators ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 265
Author(s):  
Ronald Barrett-Gonzalez ◽  
Nathan Wolf
Keyword(s):  
Aspect Ratio ◽  
Flight Control ◽  
High Speed ◽  
High Performance ◽  
Dynamic Range ◽  
Feedback System ◽  
Analytical Models ◽  
Control Surface ◽  
Operational Environment ◽  
Low Aspect Ratio

This paper covers a class of actuators for modern high speed, high performance subscale aircraft. The paper starts with an explanation of the challenges faced by micro aircraft, including low power, extremely tight volume constraints, and high actuator bandwidth requirements. A survey of suitable actuators and actuator materials demonstrates that several classes of piezoceramic actuators are ideally matched to the operational environment. While conventional, linear actuation of piezoelectric actuators can achieve some results, dramatic improvements via reverse-biased spring mechanisms can boost performance and actuator envelopes by nearly an order of magnitude. Among the highest performance, low weight configurations are post-buckled precompressed (PBP) actuator arrangements. Analytical models display large deflections at bandwidths compatible with micro aircraft flight control speed requirements. Bench testing of an example PBP micro actuator powered low aspect ratio flight control surface displays +/−11° deflections through 40 Hz, with no occupation of volume within the aircraft fuselage and good correlation between theory and experiment. A wind tunnel model of an example high speed micro aircraft was fabricated along with low aspect ratio PBP flight control surfaces, demonstrating stable deflection characteristics with increasing speed and actuator bandwidths so high that all major aeromechanical modes could be easily controlled. A new way to control such a PBP stabilator with a Limit Dynamic Driver is found to greatly expand the dynamic range of the stabilator, boosting the dynamic response of the stabilator by more than a factor of four with position feedback system engaged.

scholarly journals Stall Inception in a High-Speed Low Aspect Ratio Fan Including the Effects of Casing Treatments

1994 ◽  
Author(s):  
S. E. Gorrell ◽  
P. M. Russler
Keyword(s):  
Aspect Ratio ◽  
High Speed ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Stall Inception ◽  
Casing Treatment ◽  
Low Aspect Ratio ◽  
Casing Treatments

The stall inception process in high-speed compressor components is important to understand in order to increase stage loading while maintaining stall margin. This paper presents the results of an in depth experimental investigation on the stall inception of a two stage, high-speed, low aspect ratio fan that is representative of current operational commercial and military fan technology. High-response static pressure measurements are presented which detail the stall inception process of the fan under various operating conditions. These conditions include: varied corrected speeds, a smooth case, a circumferential groove casing treatment, and a recirculating cavity casing treatment. Stage pressure characteristics and radial pressure ratio profiles are presented for the different operating conditions. The stage performance data, together with the static pressure data, are analyzed to provide a clear and thorough understanding of the stall inception process and how the process may vary under different conditions. Experimental results show that a stage may stall on the positive, neutral, or negative sloped part of the pressure characteristic. The three casing treatments had a significant effect on the rotor tip flow and these variations changed the stall inception path of the fan. Stall inception was characterized by the formation of a stall inception cell which grew to fully developed rotating stall. Properties affected by the changing tip flow include the stall inception duration, stall inception cell frequency, existence of modal waves, duration of modal waves, and modal wave frequency. In some instances modal waves appear to play a role in stall inception, in others they do not.

Sign in / Sign up

Export Citation Format

Share Document