scholarly journals A Fast Prediction Model for Heat Transfer of Hot-Wall Heat Exchanger Based on Analytical Solution

2018 ◽  
Vol 9 (1) ◽  
pp. 72 ◽  
Author(s):  
Wenju Hu ◽  
Peng Jia ◽  
Jinzhe Nie ◽  
Yan Gao ◽  
Qunli Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Resistance ◽  
Heat Conductivity ◽  
Convective Heat Transfer Coefficient ◽  
Side Wall ◽  
Analytic Solutions ◽  
Heat Convection ◽  
Thermal Engineering ◽  
Fast Prediction

The hot-wall heat exchanger (HWHE) has been widely used in thermal engineering fields such as ceiling radiant heating/cooling, refrigerator condenser, solar heat collection, and high-temperature heat recovery. However, the numerical simulation normally used for heat transfer prediction in HWHE is usually not as convenient as the analytic solutions in engineering applications. In this paper, a new heat transfer mathematical model of HWHE-based on analytic solutions was developed, which could be much faster to obtain the heat transfer properties of HWHE. The proposed model was validated under four conditions with literature values, which showed that the deviations of heat flux are 2.53%, 0.99%, 2.12%, and 1.96%, indicating its accuracy is satisfied. The model was then used to analyze the thermal property of HWHE. The results show the thermal resistance caused by panel with heat convection and conduction accounts for 96.54% of HWHE thermal resistance, and the thermal resistance caused by heat convection on the surface of panel is 74.43%. The analyzation results also show that adding aluminum foil around pipes could decrease HWHE thermal resistance by 5.11%. Besides, the influence of pipe diameters, pipe distance, pipe heat conductivity, side wall heat conductivity, and convective heat transfer coefficient on the heat transfer performance of HWHE was analyzed. The research in this paper can be used for fast prediction and optimization of heat transfer in HWHE.

scholarly journals Effect of Magnetic Nanofluids on the Performance of a Fin-Tube Heat Exchanger

2021 ◽  
Vol 11 (19) ◽  
pp. 9261
Author(s):  
Yun-Seok Choi ◽  
Youn-Jea Kim
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Magnetic Fields ◽  
Heat Transfer Performance ◽  
Permanent Magnets ◽  
Convective Heat Transfer Coefficient ◽  
Transfer Performance ◽  
Tube Heat Exchanger ◽  
Improve Heat Transfer ◽  
Fin Tube

As electrical devices become smaller, it is essential to maintain operating temperature for safety and durability. Therefore, there are efforts to improve heat transfer performance under various conditions, such as using extended surfaces and nanofluids. Among them, cooling methods using ferrofluid are drawing the attention of many researchers. This fluid can control the movement of the fluid in magnetic fields. In this study, the heat transfer performance of a fin-tube heat exchanger, using ferrofluid as a coolant, was analyzed when external magnetic fields were applied. Permanent magnets were placed outside the heat exchanger. When the magnetic fields were applied, a change in the thermal boundary layer was observed. It also formed vortexes, which affected the formation of flow patterns. The vortex causes energy exchanges in the flow field, activating thermal diffusion and improving heat transfer. A numerical analysis was used to observe the cooling performance of heat exchangers, as the strength and number of the external magnetic fields were varying. VGs (vortex generators) were also installed to create vortex fields. A convective heat transfer coefficient was calculated to determine the heat transfer rate. In addition, the comparative analysis was performed with graphical results using contours of temperature and velocity.

scholarly journals OPTIMASI RONGGA TERHADAP VARIASI DERAJAT KEVAKUMAN SEBAGAI ISOLATOR

2012 ◽  
Vol 11 (1) ◽  
pp. 63 ◽  
Author(s):  
MULYONO MULYONO
Keyword(s):  
Heat Transfer ◽  
Specific Gravity ◽  
Thermal Resistance ◽  
Heat Convection ◽  
Vacuum Pressure ◽  
Temperature Conductivity ◽  
Easy Task ◽  
Insulation Materials ◽  
The World ◽  
Natural Heat Convection

In the world of industry, insulation materials are often utilized to maintain the temperature,either low or high. However, since the insulation materials often need to be thick, thus,costly, they are frequently deemed impractical. Therefore, in the attempt to replace the insulationmaterials, a cavity with low vacuum pressure is opted for. Yet, to attain a total (100%) airfreecavity is not an easy task. Such, the cavity usually still bears some amount of air pressurewhich results in natural heat convection through the two surfaces making up the cavity. Thetransfer coefficient of natural heat convection (h) is influenced by some factors, such as, the temperaturedifference, geometry of the cavity, cavity orientation, and characteristics of the fluid,for instance, its pressure, temperature, conductivity, specific gravity (density), and viscosity.The purpose of the study is to find answers to the following question: “How do vacuum pressurevariation and cavity ratio affect the rate of natural heat convection through the a cavity?” Pertinentto the question, the study was aimed to find the appropriate value of the vacuum pressurewhich can function well as an insulator. This study is significant in the attempt to lower downthe rate of heat transfer taking place in a system vis-à-vis the surrounding media. The studyfound out that the degree of emptiness of -60 cm Hg and =5.96, results in a lower rate of heattransfer compared with -20 cm Hg and -40 cm Hg. This means that the vacuum pressure of-60cm Hg bears a bigger thermal resistance than the -20 cm Hg and -40 cm Hg do.

Development of a Computer Program for the Numerical Investigation of Heat Transfer in a Gasketed Plate Heat Exchanger

2010 ◽  
Author(s):  
Gizem Gulben ◽  
Selin Aradag ◽  
Nilay Sezer-Uzol ◽  
Ufuk Atamturk
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Computer Program ◽  
Working Conditions ◽  
Convective Heat Transfer Coefficient ◽  
Plate Heat Exchanger ◽  
Design Parameters ◽  
Outlet Temperature ◽  
Pressure Drops ◽  
Plate Heat

In this study, a computer program is developed to calculate characteristics of a Chevron type gasketed plate heat exchanger (CTGPHEX) such as: the number of plates, the effective surface area and total pressure drops. The main reason to prefer the use of CTGPHEXs to other various types of heat exchangers is that the heat transfer efficiency is much higher in comparison. Working conditions such as the flow rates and inlet and outlet temperature of both flow sides and plate design parameters are used as an input in the program. The Logarithmic Mean Temperature Method and the different correlations for convective heat transfer coefficient and Fanning factor that are found in the literature are applied to calculate the minimum necessary effective heat transfer area, the number of plate and pressure drops due to friction for both fluid sides of fulfill the desired heat transfer rate. This Turkish / English language optioned user friendly computer program is targeted to be used in domestic companies to design and select CTGPHEXs for any desired working conditions.

Simulation of Heat Transfer to Turbulent Nanofluid Flow in an Annular Passage

2014 ◽  
Vol 925 ◽  
pp. 625-629 ◽  
Author(s):  
C.S. Oon ◽  
A. Badarudin ◽  
S.N. Kazi ◽  
M. Fadhli
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Titanium Oxide ◽  
Convective Heat Transfer Coefficient ◽  
Hot Water ◽  
Transfer Coefficients ◽  
Ansys Fluent ◽  
Heat Transfer Coefficients

The heat transfer in annular heat exchanger with titanium oxide of 1.0 volume % concentration as the medium of heat exchanger is considered in this study. The heat transfer simulation of the flow is performed by using Computational Fluid Dynamics package, Ansys Fluent. The heat transfer coefficients of water to titanium oxide nanofluid flowing in a horizontal counter-flow heat exchanger under turbulent flow conditions are investigated. The results show that the convective heat transfer coefficient of the nanofluid is slightly higher than that of the base fluid by several percents. The heat transfer coefficient increases with the increase of the mass flow rate of hot water and also the nanofluid.

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

A Simple Thermal Resistance Model for Open Cell Metal Foams

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Pradeep. M. Kamath ◽  
C. Balaji ◽  
S. P. Venkateshan
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Contact Resistance ◽  
Convective Heat Transfer Coefficient ◽  
Vertical Channel ◽  
Metal Foams ◽  
Experimental Results ◽  
Actual Case ◽  
Open Cell ◽  
Resistance Model

This paper presents a methodology for obtaining the convective heat transfer coefficient from the wall of a heated aluminium plate, placed in a vertical channel filled with open cell metal foams. For accomplishing this, a thermal resistance model from literature for metal foams is suitably modified to account for contact resistance. The contact resistance is then evaluated using the experimental results. A correlation for the estimation of the contact resistance as a function of the pertinent parameters, based on the above approach is developed. The model is first validated with experimental results in literature for the asymptotic case of negligible contact resistance. A parametric study of the effect of different foam parameters on the heat transfer is reported with and without the presence of contact resistance. The significance of the effect of contact resistance in the mixed convection and forced convection regimes is discussed. The procedure to employ the present methodology in an actual case is demonstrated and verified with additional, independent experimental data.

scholarly journals Horizontal earth-air heat exchanger for preheating external air in the mechanical ventilation system

2018 ◽  
Vol 13 (1) ◽  
pp. 71-76
Author(s):  
Vasyl Zhelykh ◽  
Olena Savchenko ◽  
Vadym Matusevych
Keyword(s):  
Heat Transfer ◽  
Mechanical Ventilation ◽  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Exchangers ◽  
Convective Heat Transfer Coefficient ◽  
Ventilation System ◽  
Heat Pipes ◽  
Heat Exchanger Tube ◽  
Exchanger Tube

Abstract To save traditional energy sources in mechanical ventilation systems, it is advisable to use low-energy ground energy for preheating or cooling the outside air. Heat exchange between ground and outside air occurs in ground heat exchangers. Many factors influence the process of heat transfer between air in the heat exchanger and the ground, in particular geological and climatic parameters of the construction site, parameters of the ventilation air in the projected house, physical and geometric parameters of the heat exchanger tube. Part of the parameters when designing a ventilation system with earth-air heat exchangers couldn’t be changed. The one of the factors, the change which directly affects the process of heat transfer between ground and air, is convective heat transfer coefficient from the internal surface of the heat exchanger tube. In this article the designs of a horizontal earthair heat exchanger with heat pipes was proposed. The use of heat pipes in designs of a horizontal heat exchanger allows intensification of the process of heat exchange by turbulence of air flow inside the heat exchanger. Besides this, additionally heat transfer from the ground to the air is carried out at the expense of heat transfer in the heat pipe itself.

Sign in / Sign up

Export Citation Format

Share Document