The effect of vibrations on the mechanical properties of laminations

This study aims to increase the mechanical properties of the composite material manufactured by the lamination process. In this study, the lamination process will be implemented in two ways, and mechanical properties are compared between the two methods. The first method covers the lamination process under the influence of vacuum pressure only, while in the second method lamination process is achieved by the influence of vacuum pressure and vibrate by shaker device. The results showed that the endurance stress of fatigue increased by 18.18% for the material manufactured by the lamination process under the influence of vibration, while the yield stress and ultimate stress values remained roughly constant for both methods.

Influence of vacuumetric pressure on thermal properties of high-temperature radioactive graphite-nitrogen system

To improve and specify the method proposed by the authors for high-temperature processing of reactor graphite in a nitrogen atmosphere, the thermodynamic data of the formed nitride compounds are supplemented and the system is calculated at a vacuum pressure of 0.5 atm. The data obtained are compared with the values at atmospheric pressure.

Feasibility Study of Vacuum Pressure Swing Adsorption for CO2 Capture From an SMR Hydrogen Plant: Comparison Between Synthesis Gas Capture and Tail Gas Capture

In this paper, a feasibility study was carried out to evaluate cyclic adsorption processes for capturing CO2 from either shifted synthesis gas or H2 PSA tail gas of an industrial-scale SMR-based hydrogen plant. It is expected that hydrogen is to be widely used in place of natural gas in various industrial sectors where electrification would be rather challenging. A SMR-based hydrogen plant is currently dominant in the market, as it can produce hydrogen at scale in the most economical way. Its CO2 emission must be curtailed significantly by its integration with CCUS. Two Vacuum Pressure Swing Adsorption (VPSA) systems including a rinse step were designed to capture CO2 from an industrial-scale SMR-based hydrogen plant: one for the shifted synthesis gas and the other for the H2 PSA tail gas. Given the shapes of adsorption isotherms, zeolite 13X and activated carbon were selected for tail gas and syngas capture options, respectively. A simple Equilibrium Theory model developed for the limiting case of complete regeneration was taken to analyse the VPSA systems in this feasibility study. The process performances were compared to each other with respect to product recovery, bed productivity and power consumption. It was found that CO2 could be captured more cost-effectively from the syngas than the tail gas, unless the desorption pressure was too low. The energy consumption of the VPSA was comparable to those of the conventional MDEA processes.

Experimental study on essential anise star oil purification in vacuum batch distillation

Vietnam is one of the world’s largest annual anise harvest countries. However, products from anise are mainly in the form of dried anise fruit and crude star anise essential oil with low economic value. The main component of the star anise essential oil is trans-anethole which needs to be purified to produce higher-value products. This study focused on building an experimental system for purifying star anise essential oil by a batch distillation column working at vacuum pressure. The products obtained during the purification process were analysed by gas chromatography-mass spectrometry (GC-MS). Analytical results were used to evaluate the ability to separate volatile impurities in the crude star anise essential oil. Results showed that the bottom temperature of the tower below 150oC, corresponding to a vacuum pressure of less than 0.1 bar, can reduce the thermal decomposition of essential oils. The volatile components, such as α-pinene, β-phellandrene, limonene, and linalool, were thoroughly separated at the top of the tower. The purified star anise essential oil was from the bottom of the distillation and had the anethole composition of over 88% of mass fraction (wt.%). Anethole recovery efficiency was 98.5 and 88.8% at a pressure of 0.1 and 0.08 bar, respectively. The bottom product can have a higher anethole composition if increasing the column height, the reflux ratio, and decreasing the pressure and the quality of impurities removed at the top is increased.The experimental results are helpful for the calculation, design, manufacture, and operation of an industrial-scale essential oil purification system.

Improved method of manufacturing carbon nanotube infused multifunctional 3D woven composites

This research work aimed to develop smart multifunctional composites via a process for uniformly dispersing carbon nanotubes (CNT) on an orthogonal three-dimensional (3D) woven glass fabric with minimised filtering effect. These smart composites could detect strain under tensile and flexural loading by the piezoresistive response of the infused CNT network. Conventional vacuum assisted resin transfer moulding was modified to control the infusion of 0.25 wt% CNT on the 3D woven glass fabric by varying the vacuum pressure. Results showed that at 101.3 kPa vacuum pressure, the CNT percolated through the thickness of the orthogonal 3D woven glass fabric while being marginally filtered by the fibres and were suitable for sensing tensile strain, whereas at 30.4 kPa, the CNT were deposited only on the surface of the fabric preform without getting filtered and were suitable for sensing flexural strain.

Formation mechanism of clogging of dredge slurry under vacuum preloading by using digital image technology

Vacuum preloading combined with prefabricated vertical drains (PVDs) system has been widely used to improve the soft clay with high water content. Clogging is usually formed around the PVDs during the vacuum preloading, impeding the propagation of the vacuum pressure and slowing down the consolidation process. In order to understand the forming mechanism of the clogging, particle image velocimetry (PIV) technique and particle tracking velocimetry (PTV) technique were adopted in the model test of vacuum preloading test. Through this study, three stages can be identified from the results of water volume discharge rate and maximum displacements versus time. In the first stage, the soil around the PVD is horizontal consolidated, which leads to the rapid formation of clogging. In the second stage, the formation of clogging slows down due to the loss of vacuum pressure, which further reduces the drainage. In the third stage, the clogging tends to be stable, and the drainage consolidation rate is significantly reduced. PTV results show that there is difference in the displacement of large and small particles during improvement. Two methods were proposed to estimate the thickness of clogging zone, reflecting a growing layer of clogging zone compressed around the PVD. This study provides new insights to investigate the formation mechanism of clogging during vacuum preloading test.