scholarly journals Three-Dimensional Modelling of Precipitation Enhancement by Cloud Seeding in Three Different Climate Zones

Atmosphere ◽  
2019 ◽  
Vol 10 (6) ◽  
pp. 294 ◽  
Author(s):  
Mladjen Ćurić ◽  
Miloš Lompar ◽  
Djordje Romanic ◽  
Linda Zou ◽  
Haoran Liang
Keyword(s):  
United Arab Emirates ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Arid Climate ◽  
Weather Research And Forecasting ◽  
Effective Precipitation ◽  
Surface Precipitation ◽  
Low Humidity ◽  
Seeding Agent ◽  
Precipitation Enhancement

This study numerically investigates precipitation enhancement from cumuliform clouds in three different climate regions: (1) Arid climate of the United Arab Emirates (UAE); (2) maritime climate of Thailand; and (3) continental climate of Serbia. Recently developed core/shell sodium chloride (NaCl)/titanium dioxide (TiO2) nanostructure (CSNT) aerosol was tested as a precipitation enhancer in all three climate regions. Previous experimental studies in cloud chambers and idealized numerical simulations demonstrated that CSNT is a significantly more effective precipitation enhancer than the traditional NaCl. Here, CSNT and NaCl seeding agents are incorporated into the WRF (Weather Research and Forecasting) model microphysics with explicate treatment of aerosol. Our results show that CSNT is a profoundly more effective precipitation enhancer in the case of arid climate characterized with low humidity. The accumulated surface precipitation in the arid test was 1.4 times larger if CSNT seeding agent was used instead of NaCl. The smallest difference in the effectiveness between CSNT and NaCl was observed in the maritime case due to their similar activation properties at high values of relative humidity.

Comparison of Two-Moment Bulk Microphysics Schemes in Idealized Supercell Thunderstorm Simulations

2011 ◽  
Vol 139 (4) ◽  
pp. 1103-1130 ◽  
Author(s):  
Hugh Morrison ◽  
Jason Milbrandt
Keyword(s):  
Three Dimensional ◽  
Wrf Model ◽  
Weather Research And Forecasting ◽  
Cold Pool ◽  
Fall Velocity ◽  
Surface Precipitation ◽  
Single Category ◽  
Supercell Thunderstorm ◽  
Drop Size Distributions ◽  
Reduced Surface

Idealized three-dimensional supercell simulations were performed using the two-moment bulk microphysics schemes of Morrison and Milbrandt–Yau in the Weather Research and Forecasting (WRF) model. Despite general similarities in these schemes, the simulations were found to produce distinct differences in storm structure, precipitation, and cold pool strength. In particular, the Morrison scheme produced much higher surface precipitation rates and a stronger cold pool, especially in the early stages of storm development. A series of sensitivity experiments was conducted to identify the primary differences between the two schemes that resulted in the large discrepancies in the simulations. Different approaches in treating graupel and hail were found to be responsible for many of the key differences between the baseline simulations. The inclusion of hail in the baseline simulation using the Milbrant–Yau scheme with two rimed-ice categories (graupel and hail) had little impact, and therefore resulted in a much different storm than the baseline run with the single-category (hail) Morrison scheme. With graupel as the choice of the single rimed-ice category, the simulated storms had considerably more frozen condensate in the anvil region, a weaker cold pool, and reduced surface precipitation compared to the runs with only hail, whose higher terminal fall velocity inhibited lofting. The cold pool strength was also found to be sensitive to the parameterization of raindrop breakup, particularly for the Morrison scheme, because of the effects on the drop size distributions and the corresponding evaporative cooling rates. The use of a more aggressive implicit treatment of drop breakup in the baseline Morrison scheme, by limiting the mean–mass raindrop diameter to a maximum of 0.9 mm, opposed the tendency of this scheme to otherwise produce large mean drop sizes and a weaker cold pool compared to the hail-only run using the Milbrandt–Yau scheme.

scholarly journals Targeting hepatocyte growth factor in epithelial–stromal interactions in an in vitro experimental model of human periodontitis

Odontology ◽  
2021 ◽  
Author(s):  
Yoko Yamaguchi ◽  
Akira Saito ◽  
Masafumi Horie ◽  
Akira Aoki ◽  
Patrick Micke ◽  
...  
Keyword(s):  
Growth Factor ◽  
Hepatocyte Growth Factor ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Collagen Gel ◽  
Neutralizing Antibody ◽  
Chronic Inflammatory Disease ◽  
Collagen Degradation ◽  
Hepatocyte Growth

AbstractPeriodontitis is a chronic inflammatory disease leading to progressive connective tissue degradation and loss of the tooth-supporting bone. Clinical and experimental studies suggest that hepatocyte growth factor (HGF) is involved in the dysregulated fibroblast–epithelial cell interactions in periodontitis. The aim of this study was to explore effects of HGF to impact fibroblast-induced collagen degradation. A patient-derived experimental cell culture model of periodontitis was applied. Primary human epithelial cells and fibroblasts isolated from periodontitis-affected gingiva were co-cultured in a three-dimensional collagen gel. The effects of HGF neutralizing antibody on collagen gel degradation were tested and transcriptome analyses were performed. HGF neutralizing antibody attenuated collagen degradation and elicited expression changes of genes related to extracellular matrix (ECM) and cell adhesion, indicating that HGF signaling inhibition leads to extensive impact on cell–cell and cell–ECM interactions. Our study highlights a potential role of HGF in periodontitis. Antagonizing HGF signaling by a neutralizing antibody may represent a novel approach for periodontitis treatment.

scholarly journals Numerical and Experimental Studies on a Three-Dimensional Numerical Wave Tank

IEEE Access ◽  
2018 ◽  
Vol 6 ◽  
pp. 6585-6593 ◽  
Author(s):  
Xiaojie Tian ◽  
Qingyang Wang ◽  
Guijie Liu ◽  
Wei Deng ◽  
Zhiming Gao
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Numerical Wave Tank ◽  
Wave Tank ◽  
Numerical Wave

Numerical Modeling of Tube Hydropiercing Using Phenomenological and Micro-Mechanical Damage Criteria

2013 ◽  
Vol 549 ◽  
pp. 172-179 ◽  
Author(s):  
Amir Hassannejadasl ◽  
Daniel E. Green
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Equivalent Plastic Strain ◽  
Mechanical Damage ◽  
High Strength ◽  
Dimensional Finite Element ◽  
Steel Dp600 ◽  
Three Dimensional Finite Element ◽  
Jc Model ◽  
Damage Criteria

Hydropiercing is an efficient way of piercing holes in mass produced hydroformed parts with complex geometries. By driving piercing punches radially into a hydroformed and fully pressurized tube, holes will be pierced and extruded into the tube-wall. Recent experimental studies have shown that the formability of advanced high strength steel (AHSS) tubes can be increased with the application of internal pressure. In this study, three-dimensional finite element simulations of a tube hydropiercing process of a dual phase steel (DP600) were performed in LS-DYNA, using phenomenological, micromechanical and combined damage criteria. Damage was included in the numerical analysis by applying constant equivalent plastic strain (CEPS), the Gurson-Tvergaard-Needleman (GTN), and the Extended GTN (GTN+JC) model. In order to calibrate the parameters in each model, a specialized hole-piercing fixture was designed and piercing tests were carried out on non-pressurized tube specimens. Of the various ductile fracture criteria, the results predicted with the GTN+JC model, such as the punch load-displacement, the roll-over depth, and the quality of the clearance zone correlated the best with the experimental data.

Fracture Mechanics of Thin Plates and Shells Under Combined Membrane, Bending, and Twisting Loads

2005 ◽  
Vol 58 (1) ◽  
pp. 37-48 ◽  
Author(s):  
Alan T. Zehnder ◽  
Mark J. Viz
Keyword(s):  
Fracture Mechanics ◽  
Plate Theory ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Crack Tip ◽  
Thin Plates ◽  
Element Analysis ◽  
Crack Tip Fields ◽  
Plates And Shells ◽  
Membrane Bending

The fracture mechanics of plates and shells under membrane, bending, twisting, and shearing loads are reviewed, starting with the crack tip fields for plane stress, Kirchhoff, and Reissner theories. The energy release rate for each of these theories is calculated and is used to determine the relation between the Kirchhoff and Reissner theories for thin plates. For thicker plates, this relationship is explored using three-dimensional finite element analysis. The validity of the application of two-dimensional (plate theory) solutions to actual three-dimensional objects is analyzed and discussed. Crack tip fields in plates undergoing large deflection are analyzed using von Ka´rma´n theory. Solutions for cracked shells are discussed as well. A number of computational methods for determining stress intensity factors in plates and shells are discussed. Applications of these computational approaches to aircraft structures are examined. The relatively few experimental studies of fracture in plates under bending and twisting loads are also reviewed. There are 101 references cited in this article.

Noninvasive three-dimensional electrocardiographic imaging of ventricular activation sequence

2005 ◽  
Vol 289 (6) ◽  
pp. H2724-H2732 ◽  
Author(s):  
Xin Zhang ◽  
Indiresha Ramachandra ◽  
Zhongming Liu ◽  
Basharat Muneer ◽  
Steven M. Pogwizd ◽  
...  
Keyword(s):  
Surface Potential ◽  
Body Surface ◽  
Cardiac Arrhythmias ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Electrocardiographic Imaging ◽  
Ventricular Activation ◽  
Body Surface Potential ◽  
Life Threatening ◽  
Activation Sequence

Imaging the myocardial activation sequence is critical for improved diagnosis and treatment of life-threatening cardiac arrhythmias. It is desirable to reveal the underlying cardiac electrical activity throughout the three-dimensional (3-D) myocardium (rather than just the endocardial or epicardial surface) from noninvasive body surface potential measurements. A new 3-D electrocardiographic imaging technique (3-DEIT) based on the boundary element method (BEM) and multiobjective nonlinear optimization has been applied to reconstruct the cardiac activation sequences from body surface potential maps. Ultrafast computerized tomography scanning was performed for subsequent construction of the torso and heart models. Experimental studies were then conducted, during left and right ventricular pacing, in which noninvasive assessment of ventricular activation sequence by means of 3-DEIT was performed simultaneously with 3-D intracardiac mapping (up to 200 intramural sites) using specially designed plunge-needle electrodes in closed-chest rabbits. Estimated activation sequences from 3-DEIT were in good agreement with those constructed from simultaneously recorded intracardiac electrograms in the same animals. Averaged over 100 paced beats (from a total of 10 pacing sites), total activation times were comparable (53.3 ± 8.1 vs. 49.8 ± 5.2 ms), the localization error of site of initiation of activation was 5.73 ± 1.77 mm, and the relative error between the estimated and measured activation sequences was 0.32 ± 0.06. The present experimental results demonstrate that the 3-D paced ventricular activation sequence can be reconstructed by using noninvasive multisite body surface electrocardiographic measurements and imaging of heart-torso geometry. This new 3-D electrocardiographic imaging modality has the potential to guide catheter-based ablative interventions for the treatment of life-threatening cardiac arrhythmias.

Experimental Studies of Leading Edge Contouring Influence on Secondary Losses in Transonic Turbines

2012 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Noticeable Effect ◽  
Flow Angle ◽  
Wide Range ◽  
Contour Plots

An experimental study of the hub leading edge contouring using fillets is performed in an annular sector cascade to observe the influence of secondary flows and aerodynamic losses. The investigated vane is a three dimensional gas turbine guide vane (geometrically similar) with a mid-span aspect ratio of 0.46. The measurements are carried out on the leading edge fillet and baseline cases using pneumatic probes. Significant precautions have been taken to increase the accuracy of the measurements. The investigations are performed for a wide range of operating exit Mach numbers from 0.5 to 0.9 at a design inlet flow angle of 90°. Data presented include the loading, fields of total pressures, exit flow angles, radial flow angles, as well as profile and secondary losses. The vane has a small profile loss of approximately 2.5% and secondary loss of about 1.1%. Contour plots of vorticity distributions and velocity vectors indicate there is a small influence of the vortex-structure in endwall regions when the leading edge fillet is used. Compared to the baseline case the loss for the filleted case is lower up to 13% of span and higher from 13% to 20% of the span for a reference condition with Mach no. of 0.9. For the filleted case, there is a small increase of turning up to 15% of the span and then a small decrease up to 35% of the span. Hence, there are no significant influences on the losses and turning for the filleted case. Results lead to the conclusion that one cannot expect a noticeable effect of leading edge contouring on the aerodynamic efficiency for the investigated 1st stage vane of a modern gas turbine.

“Gray Zone” Simulations using a Three-Dimensional Planetary Boundary Layer Parameterization in the Weather Research and Forecasting Model

2021 ◽  
Author(s):  
Timothy W. Juliano ◽  
Branko Kosović ◽  
Pedro A. Jiménez ◽  
Masih Eghdami ◽  
Sue Ellen Haupt ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Planetary Boundary Layer ◽  
Three Dimensional ◽  
Grid Cell ◽  
Weather Research And Forecasting ◽  
Forecasting Model ◽  
Gray Zone ◽  
Pbl Scheme ◽  
3D Effects ◽  
Mesoscale Simulations

AbstractGenerating accurate weather forecasts of planetary boundary layer (PBL) properties is challenging in many geographical regions, oftentimes due to complex topography or horizontal variability in, for example, land characteristics. While recent advances in high-performance computing platforms have led to an increase in the spatial resolution of numerical weather prediction (NWP) models, the horizontal grid cell spacing (Δ x) of many regional-scale NWP models currently fall within or are beginning to approach the gray zone (i.e., Δ x ≈ 100 – 1000 m). At these grid cell spacings, three-dimensional (3D) effects are important, as the most energetic turbulent eddies are neither fully parameterized (as in traditional mesoscale simulations) nor fully resolved [as in traditional large eddy simulations (LES)]. In light of this modeling challenge, we have implemented a 3D PBL parameterization for high-resolution mesoscale simulations using the Weather Research and Forecasting model. The PBL scheme, which is based on the algebraic model developed by Mellor and Yamada, accounts for the 3D effects of turbulence by calculating explicitly the momentum, heat, and moisture flux divergences in addition to the turbulent kinetic energy. In this study, we present results from idealized simulations in the gray zone that illustrate the benefit of using a fully consistent turbulence closure framework under convective conditions. While the 3D PBL scheme reproduces the evolution of convective features more appropriately than the traditional 1D PBL scheme, we highlight the need to improve the turbulent length scale formulation.

Sign in / Sign up

Export Citation Format

Share Document