scholarly journals Test-Rig Simulation on Hybrid Thermal Barrier Coating Assisted with Cooling Air System for Advanced Gas Turbine under Prolonged Exposures—A Review

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 560
Author(s):  
Salmi Mohd Yunus ◽  
Savisha Mahalingam ◽  
Abreeza Manap ◽  
Nurfanizan Mohd Afandi ◽  
Meenaloshini Satgunam
Keyword(s):  
Gas Turbine ◽  
Operating Temperature ◽  
Peak Load ◽  
Test Rig ◽  
Steady State Condition ◽  
Barrier Coating ◽  
Air System ◽  
Cooling Air ◽  
Operational Modes ◽  
Base Load

Thermal barrier coating (TBC) and cooling air systems are among the technologies that have been introduced and applied in pursuing the extensive development of advanced gas turbine. TBC is used to protect the gas turbine components from the higher operating temperature of advanced gas turbine, whereas cooling air systems are applied to assist TBC in lowering the temperature exposure of protected surfaces. Generally, a gas turbine operates in three main operational modes, which are base load, peak load, and part peak load. TBC performance under these three operational modes has become essential to be studied, as it will provide the gas turbine owners not only with the behaviors and damage mechanism of TBC but also a TBC life prediction in a particular operating condition. For TBC under base load or so called steady-state condition, a number of studies have been reviewed and discussed. However, it has been found that most of the studies have been conducted without the assistance of a cooling air system, which does not simulate the TBC in advanced gas turbine completely. From this review, the studies on TBC-assisted cooling air system to simulate the advanced gas turbine operating conditions have also been summarized, which are limited to test rig simulations under thermal cyclic mode where thermal cyclic represents peak and part peak load conditions. The equipment used to simulate the gas turbine operating condition, test temperatures, and durations are parameters that have been taken into consideration under this review. Finally, a test rig that is capable of simulating both TBC and cooling air effects at a high operating temperature of advanced gas turbines for prolonged exposure under steady-state condition has been proposed to be developed.

Experimental and Numerical Analysis of the Flow Structure and Dust Separation Inside a Pre-Swirl Cooling Air System

2003 ◽  
Author(s):  
O. Schneider ◽  
H. J. Dohmen ◽  
F.-K. Benra ◽  
D. Brillert
Keyword(s):  
Numerical Analysis ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Internal Cooling ◽  
Flow Conditions ◽  
Test Rig ◽  
Complex Flow ◽  
Air System ◽  
Cooling Air

Improvements in efficiency and performance of gas turbines require a better understanding of the internal cooling air system which provides the turbine blades with cooling air. With the increase of cooling air passing through the internal air system, a greater amount of air borne particles is transported to the film cooling holes at the turbine blade surface. In spite of their small size, these holes are critical for blockage. Blockage of only a few holes could have harmful effects on the cooling film surrounding the blade. As a result, a reduced mean time between maintenance or even unexpected operation faults of the gas turbine during operation could occur. Experience showed a complex interaction of cooling air under different flow conditions and its particle load. To get more familiar with all these influences and the system itself, a test rig has been built. With this test rig, the behavior of particles in the internal cooling air system can be studied at realistic flow conditions compared to a modern, heavy duty gas turbine. It is possible to simulate different particle sizes and dust concentrations in the coolant air. The test rig has been designed to give information about the quantity of separated particles at various critical areas of the internal air system [1]. The operation of the test rig as well as analysis of particles in such a complex flow system bear many problems, addressed in previous papers [1,2,3]. New theoretical studies give new and more accurate results, compared to the measurements. Furthermore the inspection of the test rig showed dust deposits at unexpected positions of the flow path, which will be discussed by numerical analysis.

A Contribution to the Abrasive Effect of Particles in a Gas Turbine Pre-Swirl Cooling Air System

2005 ◽  
Author(s):  
O. Schneider ◽  
F.-K. Benra ◽  
H. J. Dohmen ◽  
K. Jarzombek
Keyword(s):  
Gas Turbine ◽  
Flow Structure ◽  
Film Cooling ◽  
Gas Turbines ◽  
Test Rig ◽  
Critical Areas ◽  
Air System ◽  
Quantitative Results ◽  
Film Cooling Holes ◽  
Cooling Air

With the increase of cooling air passing through the internal air system of modern gas turbines, a greater number of airborne particles is transported to the film cooling holes in the turbine blade surface. In spite of their small size, these holes are critical for airflow and must be free of blockage. A test rig has been designed to study the quantity of separated particles at various critical areas of the internal air system. Former publications for this conference gave detailed insight into the test rig, the flow structure and the particle motion during separation. The process of separation generates abrasion on the rotating and stationary parts of the system. When considering service and maintenance or even unexpected operation faults of the gas turbine, it is important to know the location and abrasion rate of these critical areas. The flow structure within the pre-swirl cooling air system results in locally focused abrasion regions, which are investigated in this paper. New simulations, taking additional physical effects into account, are discussed in the paper. The simulation results are compared to results obtained by measurements and observations within the test rig. Qualitative and quantitative results show the ability to predict the quantity of abrasion during operation on various critical areas of the system.

Experimental Analysis of Dust Separation in the Internal Cooling Air System of Gas Turbines

2002 ◽  
Author(s):  
O. Schneider ◽  
H. J. Dohmen ◽  
A. W. Reichert
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Rotor Blades ◽  
Internal Cooling ◽  
Test Rig ◽  
Air System ◽  
And Performance ◽  
Cooling Air

For further improvements in efficiency and performance a better understanding of the internal cooling air system of gas turbines, which provides the turbine rotor blades with cooling air, is necessary. With the increase of cooling air passing through the internal air system, a greater amount of air borne particles are transported to the film cooling holes at the turbine blade surface. In spite of their small size, these holes are critical for blade cooling. Blockage of only a few holes could have harmful effects on the cooling film surrounding the blade. As a result, a reduced mean time between maintenance or even unexpected operation faults of the gas turbine during operation occurs. With a new test rig, the behaviour of particles in the internal cooling air system could be investigated at realistic flow conditions compared to a modern, real world gas turbine. It is possible to simulate different particle sizes and dust concentrations in the coolant air. A first comparison of design expectations and measurements, showing the behaviour of air borne particles in the internal cooling air system under realistic environmental conditions is given in the paper. Further the design tools for nearly a full internal air system flow path could be validated with this new test rig.

Investigations of Dust Separation in the Internal Cooling Air System of Gas Turbines

2003 ◽  
Author(s):  
O. Schneider ◽  
H. J. Dohmen ◽  
F.-K. Benra ◽  
D. Brillert
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Internal Cooling ◽  
Flow Conditions ◽  
Test Rig ◽  
Complex Flow ◽  
Air System ◽  
Cooling Air

Improvements in efficiency and performance of gas turbines require a better understanding of the internal cooling air system which provides the turbine blades with cooling air. With the increase of cooling air passing through the internal air system, a greater amount of air borne particles is transported to the film cooling holes at the turbine blade surface. In spite of their small size, these holes are critical for blockage. Blockage of only a few holes could have harmful effects on the cooling film surrounding the blade. As a result, a reduced mean time between maintenance or even unexpected operation faults of the gas turbine during operation could occure. Experience showed a complex interaction of cooling air under different flow conditions and its particle load. To get more familiar with all these influences and the system itself, a test rig has been built. With this test rig, the behaviour of particles in the internal cooling air system could be studied at realistic flow conditions compared to a modern, heavy duty gas turbine. It is possible to simulate different particle sizes and dust concentrations in the coolant air. The test rig has been designed to give information about the quantity of separated particles at various critical areas of the internal air system [1]. The operation of the test rig as well as analysis of particles in such a complex flow system bear many problems, addressed in the previous paper [1]. New measurements and analysis methods give new and more accurate results, which will be shown in this paper. Furthermore the inspection of the test rig shows dust deposits at unexpected positions of the flow path. Theoretical studies to characterize the flow behaviour of the disperse phase in a continuous fluid using Lagrangian Tracking were also performed. A comparison between the numerical solution and the measurements will be shown in the paper.

Dust Separation in a Gas Turbine Pre-Swirl Cooling Air System: A Parameter Variation

2004 ◽  
Author(s):  
O. Schneider ◽  
H. J. Dohmen ◽  
F.-K. Benra ◽  
D. Brillert
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Flow Behavior ◽  
Internal Cooling ◽  
Test Rig ◽  
Swirl Generator ◽  
Air System ◽  
Heavy Duty Gas Turbine ◽  
Cooling Air

With the increase of cooling air passing through the internal air system of modern gas turbines, a greater amount of air borne particles is transported to the film cooling holes at the turbine blade surface. In spite of their small size, these holes are critical for blockage. A test rig has been designed to give information about the quantity of separated particles at various critical areas of the internal air system. With this test rig, the behavior of particles in the internal cooling air system could be studied at realistic flow conditions compared to a modern, heavy duty gas turbine. It is possible to simulate different particle sizes and dust concentrations in the coolant air. Numerical studies to characterize the flow behavior of the disperse phase in a continuous fluid using Lagrange Tracking were performed. The main influencing parameters, which are the mass flow through the system, the rotor speed and the nozzle angle of the pre-swirl generator, were varied. Furthermore to validate the theoretical studies, based on the presented variations a special point of operation was selected to get a comparable measurement, which is presented in the paper. Comparison between simulation and measurement shows additional influences of the particle shape, which were discussed. The resulting enhanced model and the comparison to the measurement is presented in the paper.

scholarly journals Cooling and Sealing Air System in Industrial Gas Turbine Engines

1996 ◽  
Author(s):  
A. W. Reichert ◽  
M. Janssen
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
State Of The Art ◽  
Cooling System ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Air System ◽  
Calculation System ◽  
Cooling Air

Siemens heavy duty Gas Turbines have been well known for their high power output combined with high efficiency and reliability for more than 3 decades. Offering state of the art technology at all times, the requirements concerning the cooling and sealing air system have increased with technological development over the years. In particular the increase of the turbine inlet temperature and reduced NOx requirements demand a highly efficient cooling and sealing air system. The new Vx4.3A family of Siemens gas turbines with ISO turbine inlet temperatures of 1190°C in the power range of 70 to 240 MW uses an effective film cooling technique for the turbine stages 1 and 2 to ensure the minimum cooling air requirement possible. In addition, the application of film cooling enables the cooling system to be simplified. For example, in the new gas turbine family no intercooler and no cooling air booster for the first turbine vane are needed. This paper deals with the internal air system of Siemens gas turbines which supplies cooling and sealing air. A general overview is given and some problems and their technical solutions are discussed. Furthermore a state of the art calculation system for the prediction of the thermodynamic states of the cooling and sealing air is introduced. The calculation system is based on the flow calculation package Flowmaster (Flowmaster International Ltd.), which has been modified for the requirements of the internal air system. The comparison of computational results with measurements give a good impression of the high accuracy of the calculation method used.

Managing Fuel Oil Nozzle Coking to Improve Gas Turbine Availability

2000 ◽  
Author(s):  
Leo R. Burgett ◽  
Tim Mercer
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Fuel Oil ◽  
Power Company ◽  
Ac Motor ◽  
Air System ◽  
Oil Residue ◽  
Cooling Air ◽  
Fuel Burner

Fuel oil nozzle coking has been a continuing problem for operators of gas turbine power plants. Over the years, several “solutions” to eliminate the coking of the fuel oil have been implemented to improve plant reliability and availability. When the fuel oil nozzle is “coked”, the startup and operation of the gas turbine are impaired and an unscheduled outage is needed to clean the fuel oil nozzle. In 1997, a project was initiated to investigate the coking problem as it affects the operation of the dual fuel burner of the ABB ALSTOM POWER Inc. GT11N1 single burner (SBK) gas turbine. The GT11N1 SBK fuel oil nozzle (see FIGURE 1) was failing to operate properly because of “coked” fuel oil residue on its internal components (stationary and moveable). ABB ALSTOM POWER Inc. teamed with Savannah Electric & Power Company and collected data that indicated adequate nozzle cooling air could reduce the rate of fuel oil coking. A nozzle cooling air system modification was installed on one of the ABB ALSTOM POWER Inc. 11N1 gas turbines at the Savannah Electric & Power Company McIntosh Power Plant. The modification included an AC motor driven air blower to provide cooling air to the fuel oil nozzle after shutdown of the gas turbine. Inspection of the components inside the fuel oil nozzle showed that very little fuel oil oxidation had occurred inside the nozzle during the three-month test period. By improving the fuel oil nozzle cooling air system, the coking problem can be better managed.

scholarly journals Retrofitting a 100,000 HP Simple Cycle Gas Turbine Compressor Station With Regenerators

1983 ◽  
Author(s):  
Arjo Klyn ◽  
Hans Wylens
Keyword(s):  
Gas Turbine ◽  
Transport System ◽  
Gas Turbines ◽  
Gas Transport ◽  
Peak Load ◽  
Simple Cycle ◽  
Compressor Station ◽  
Compressor Unit ◽  
Gas Turbine Compressor ◽  
Base Load

In its gas transport system N.V. Nederlandse Gasunie found a shift from peak load to base load at stations which were not originally designed for that duty. A study was made of the application of recuperators on GE frame 5 gas turbines, based on experience with a prototype installation four years ago. The paper describes the Breda-regenerator in general and the experience of one of the two prototypes which was installed on a Gasunie frame 5 two shaft 24 mW gas turbine compressor unit in 1978. In June 1981 Gasunie decided to equip two more identical gas turbine compressor units at their 100,000 HP compressor station at Zweekhorst with Breda-regenerators. The paper covers all aspects of retrofitting the simple cycle gas turbine installations with regenerators at the Zweekhorst station.

Particulate Monitor for Gas Turbine Cooling Air

2008 ◽  
Author(s):  
Richard H. Bunce ◽  
Francisco Dovali-Solis ◽  
Robert W. Baxter
Keyword(s):  
Gas Turbine ◽  
Monitoring System ◽  
Cooling System ◽  
Gas Turbine Engine ◽  
Minimum Size ◽  
Turbine Engine ◽  
Air System ◽  
Air Cooler ◽  
Secondary Air ◽  
Cooling Air

It is important to monitor the quality of the air used in the cooling system of a gas turbine engine. There can be many reasons that particulates smaller than the minimum size removed by typical engine air filters can enter the secondary air system piping in a gas turbine engine system. Siemens has developed a system that provide real time monitoring of particulate concentrations by adapting a commercial electrodynamic devise for use within the confines of the gas turbine secondary air system with provision for a grab sample option to collect samples for laboratory analysis. This on-line monitoring system is functional at typical engine cooling system piping operating pressure and temperature. The system is calibrated for detection of iron oxide particles in the 1 to 100 micrometer range at concentration of from 1 to 50 parts per million mass wet (ppmmw) The electro dynamic device is nominally operable at 800°C. The particulate monitoring system requires special mounting and antenna. This system may be adjusted for other materials, sizes and concentrations. The system and its developmental application are described. The system has been tested and test results are reviewed. The test application was the cooling air piping of a Siemens gas turbine engine. Multiple locations were monitored. The cooling system in this engine incorporates an air cooler and the particulate monitoring system was tested upstream and downstream of the air cooler for temperature contrast. The monitor itself is limited to the piping system and not the engine gas-path.

Development of the 5MW Power Generation Gas Turbine Engine

2011 ◽  
Author(s):  
Sooyong Kim ◽  
Sungryong Lee ◽  
Jewook Ryu ◽  
V. E. Spitsyn
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Nuclear Power ◽  
Peak Load ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Load Power ◽  
The Future ◽  
Lng Fuel ◽  
Base Load

Gas turbine engine has been applied to the aircraft and ship propulsion with its advantages of compactness and comparatively short starting time. With a significant improvement in gas turbine efficiency with development of super alloy materials and advancement in cooling technologies in the second half of 1990s, its importance as a source of base load as well as peak load power generation has been increasing. However, with increased demand in nuclear power and renewable energy in the 21st century, there seems to be speculations among the power generation industries that gas turbine will take more or less a buffering role supplementing the irregular inflow of electricity to the grid rather than acting as a base load power source. With the shift in the role of gas turbine from base to supplementary, CHP application based on small powered gas turbine utilizing biogas or syngas as its fuel is expected to increase in the future. In this context, this paper describes the development result of 5MW gas turbine engine for CHP application. It can be operated with LNG or syngas of low LHV fuel. Originally, the engine was designed for LNG as its primary fuel, but since the importance of syngas power generation market will be increasing in the future, a complementary work for modification of combustor part has been carried out and has been tested. However, this paper deals with the parts developed with the use of LNG fuel. The test result of emission characteristics meets the standards required in Korea. The development has been made through the cooperation of Doosan Heavy Industry (DHI, Korea) and Zory-Mashproekt (Ukraine).

Sign in / Sign up

Export Citation Format

Share Document