scholarly journals Study on the Reliability of Sn–Bi Composite Solder Pastes with Thermosetting Epoxy under Thermal Cycling and Humidity Treatment

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 733
Author(s):  
Lu Liu ◽  
Songbai Xue ◽  
Ruiyang Ni ◽  
Peng Zhang ◽  
Jie Wu
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Composite Solder ◽  
Solder Joints ◽  
Solder Paste ◽  
Epoxy System ◽  
Mechanical Reinforcement ◽  
Microstructure Observation ◽  
Temperature And Humidity ◽  
Thermosetting Epoxy

In this study, a Sn–Bi composite solder paste with thermosetting epoxy (TSEP Sn–Bi) was prepared by mixing Sn–Bi solder powder, flux, and epoxy system. The melting characteristics of the Sn–Bi solder alloy and the curing reaction of the epoxy system were measured by differential scanning calorimeter (DSC). A reflow profile was optimized based on the Sn–Bi reflow profile, and the Organic Solderability Preservative (OSP) Cu pad mounted 0603 chip resistor was chosen to reflow soldering and to prepare samples of the corresponding joint. The high temperature and humidity reliability of the solder joints at 85 °C/85% RH (Relative Humidity) for 1000 h and the thermal cycle reliability of the solder joints from −40 °C to 125 °C for 1000 cycles were investigated. Compared to the Sn–Bi solder joint, the TSEP Sn–Bi solder joints had increased reliability. The microstructure observation shows that the epoxy resin curing process did not affect the transformation of the microstructure. The shear force of the TSEP Sn–Bi solder joints after 1000 cycles of thermal cycling test was 1.23–1.35 times higher than the Sn–Bi solder joint and after 1000 h of temperature and humidity tests was 1.14–1.27 times higher than the Sn–Bi solder joint. The fracture analysis indicated that the cured cover layer could still have a mechanical reinforcement to the TSEP Sn–Bi solder joints after these reliability tests.

scholarly journals Prediction of mechanical properties and fatigue life of nano silver paste in chip interconnection

2020 ◽  
Author(s):  
Hui YANG ◽  
Jihui Wu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Stress And Strain ◽  
Nano Silver ◽  
Finite Element Software ◽  
Flip Chips ◽  
Empirical Correction ◽  
Prediction Of Mechanical Properties

Abstract The simulation of nano-silver solder joints in flip-chips is performed by the finite element software ANSYS, and the stress-strain distribution results of the solder joints are displayed. In this simulation, the solder joints use Anand viscoplastic constitutive model, which can reasonably simulate the stress and strain of solder joints under thermal cycling load. At the same time this model has been embedded in ANSYS software, so it is more convenient to use. The final simulation results show that the areas where the maximum stresses and strains occur at the solder joints are mostly distributed in the contact areas between the solder joints and the copper pillars and at the solder joints. During the entire thermal cycling load process, the area where the maximum change in stress and strain occurs is always at the solder joint, and when the temperature changes, the temperature at the solder joint changes significantly. Based on comprehensive analysis, the relevant empirical correction calculation equation is used to calculate and predict the thermal fatigue life of nano-silver solder joints. The analysis results provide a reference for the application of nano-silver solder in the electronic packaging industry.

The Future of Solder Joint Encapsulant

2015 ◽  
Vol 2015 (1) ◽  
pp. 000644-000648
Author(s):  
Mary Liu ◽  
Wusheng Yin
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Lower Cost ◽  
Solder Joints ◽  
Cost Of Ownership ◽  
The Future ◽  
High Temperature Solder

Solder joint encapsulant adhesives have been successfully used to enhance the strength of solder joints and improve thermal cycling as well as drop performance in finished products. The use of solder joint encapsulant adhesives can eliminate the need for underfill materials and the underfill process altogether, thus simplifying rework, which results in a lower cost of ownership. Solder joint encapsulant adhesives include: low temperature and high temperature solder joint encapsulant adhesives, and their derivatives. Each solder joint encapsulant adhesive has: unfilled and filled solder joint encapsulant adhesives, and solder joint encapsulant paste. Each solder joint encapsulant product has been designed for different applications. In this paper, we are going to discuss the details and future of solder joint encapsulant adhesives.

Predicting Thermal Fatigue Lifetimes for SMT Solder Joints

1992 ◽  
Vol 114 (4) ◽  
pp. 472-476 ◽  
Author(s):  
J. Sauber ◽  
J. Seyyedi
Keyword(s):  
Finite Element ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Thermal Fatigue ◽  
Solder Joints ◽  
Finite Element Models ◽  
Creep Tests ◽  
Creep Equation ◽  
Joint Behavior ◽  
Creep Strains

A power-law type creep equation has been added to finite element models to calculate solder joint response to time, temperature, and stress level. The ability of the models to predict solder joint behavior was verified by running a series of creep tests. The models were then solved to determine the solder joint creep strains which occur during thermal cycling. These creep strains were used to predict the degradation of pull strength resulting from thermal cycling. More than 8,600 solder joints were thermally cycled and then individually pull tested to verify the accuracy of the method.

SAC–xTiO2 nano-reinforced lead-free solder joint characterizations in ultra-fine package assembly

2018 ◽  
Vol 30 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Fakhrozi Che Ani ◽  
Azman Jalar ◽  
Abdullah Aziz Saad ◽  
Chu Yee Khor ◽  
Roslina Ismail ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Solder Joint ◽  
Solder Joints ◽  
Ion Beam ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Content Type ◽  
X Ray ◽  
Free Solder

Purpose This paper aims to investigate the characteristics of ultra-fine lead-free solder joints reinforced with TiO2 nanoparticles in an electronic assembly. Design/methodology/approach This study focused on the microstructure and quality of solder joints. Various percentages of TiO2 nanoparticles were mixed with a lead-free Sn-3.5Ag-0.7Cu solder paste. This new form of nano-reinforced lead-free solder paste was used to assemble a miniature package consisting of an ultra-fine capacitor on a printed circuit board by means of a reflow soldering process. The microstructure and the fillet height were investigated using a focused ion beam, a high-resolution transmission electron microscope system equipped with an energy dispersive X-ray spectrometer (EDS), and a field emission scanning electron microscope coupled with an EDS and X-ray diffraction machine. Findings The experimental results revealed that the intermetallic compound with the lowest thickness was produced by the nano-reinforced solder with a TiO2 content of 0.05 Wt.%. Increasing the TiO2 content to 0.15 Wt.% led to an improvement in the fillet height. The characteristics of the solder joint fulfilled the reliability requirements of the IPC standards. Practical implications This study provides engineers with a profound understanding of the characteristics of ultra-fine nano-reinforced solder joint packages in the microelectronics industry. Originality/value The findings are expected to provide proper guidelines and references with regard to the manufacture of miniaturized electronic packages. This study also explored the effects of TiO2 on the microstructure and the fillet height of ultra-fine capacitors.

Thermal Cycling Reliability of Chip Resistor Lead Free Solder Joints

2003 ◽  
Author(s):  
N. Islam ◽  
J. C. Suhling ◽  
P. Lall ◽  
T. Shete ◽  
H. S. Gale ◽  
...  
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Fatigue Resistance ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Snagcu Alloy ◽  
Temperature Ranges ◽  
Free Solder

In this study, we have examined the thermal cycling reliability of several lead free chip resistor solder joint configurations. Five sizes of resistors (2512, 1206, 0805, 0603, 0402), 2 temperature ranges (−40 to 125°C and −40 to 150°C), and five different solder types have been examined. The solders include the normal SnAgCu alloy recommended by earlier studies (95.5Sn-3.8Ag-0.7Cu), and several variations that include small percentages of Bismuth and Indium to enhance fatigue resistance. Results have been compared to data for standard 63Sn-37Pb joints.

Reliability Evaluation of BGA Solder Joints by Using Thermal Fatigue Models

2005 ◽  
Author(s):  
Ouk Sub Lee ◽  
No Hoon Myoung ◽  
Dong Hyeok Kim
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Thermal Fatigue ◽  
Failure Probability ◽  
Solder Joints ◽  
State Function ◽  
Mechanical Loads ◽  
First Order ◽  
Reliability Method ◽  
Fatigue Model

The use of Ball Grid Array (BGA) interconnects utilizing the BGA solder joint has grown rapidly because of its small volume and diversity of its application. Therefore, the continuous quantification and refinement of BGA solder joint in terms of its reliability are required. The creep and cyclically applied mechanical loads generally cause metal fatigue on the BGA solder joint which inevitably leads to an electrical discontinuity. In the field application, the BGA solder joints are known to experience mechanical loads during temperature changes caused by power up/down events as the result of the Coefficient of Thermal Expansion (CTE) mismatch between the substrate and the Si die. In this paper, extremely small resistance changes in the lead free joints corresponding to the through-cracks generated by the thermal fatigue were measured and the failure was defined in terms of anomalous changes in the joint resistance. Furthermore, the reliability of BGA solder joints under thermal cycling was evaluated by using a criterion that may define and distinguish a failure in the solder joint. Any changes in circuit resistance according to the accumulated damage induced by the thermal cycling in the joint were recorded and evaluated by the First Order Reliability Method (FORM) procedure in order to quantify the reliability of solder joint. The first order Taylor series expansion of the limit state function incorporating with thermal fatigue models is used in order to estimate the failure probability of solder joints under heated condition. Various thermal fatigue models are utilized in this study. Models based on various plastic-strain rates such as Coffin-Manson fatigue model, total strain fatigue model and Solomon fatigue model are utilized in this study. The effects of random variables such as the CTE, the pitch of solder joint, the diameter of solder joint, and the CTE difference solder joints on the failure probability of the solder joint are systematically investigated by using a failure probability model with the FORM.

scholarly journals Shear Strength and Aging Characteristics of Sn-3.0Ag-0.5Cu/Cu Solder Joint Reinforced with ZrO2 Nanoparticles

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1295
Author(s):  
Sri Harini Rajendran ◽  
Seung Jun Hwang ◽  
Jae Pil Jung
Keyword(s):  
Shear Strength ◽  
Solder Joint ◽  
Solder Joints ◽  
Solder Matrix ◽  
Fracture Analysis ◽  
Zro2 Nanoparticles ◽  
Solder Paste ◽  
Lap Shear ◽  
Matrix Fracture ◽  
The Matrix

This study investigates the shear strength and aging characteristics of Sn-3.0Ag-0.5Cu (SAC 305)/Cu joints by the addition of ZrO2 nanoparticles (NPs) having two different particle size: 5–15 nm (ZrO2A) and 70–90 nm (ZrO2B). Nanocomposite pastes were fabricated by mechanically mixing ZrO2 NPs and the solder paste. ZrO2 NPs decreased the β-Sn grain size and Ag3Sn intermetallic compound (IMC) in the matrix and reduced the Cu6Sn5 IMC thickness at the interface of lap shear SAC 305/Cu joints. The effect is pronounced for ZrO2A NPs added solder joint. The solder joints were isothermally aged at 175 °C for 24, 48, 144 and 256 h. NPs decreased the diffusion coefficient from 1.74 × 10–16 m/s to 3.83 × 10–17 m/s and 4.99 × 10–17 m/s for ZrO2A and ZrO2B NPs added SAC 305/Cu joints respectively. The shear strength of the solder joints decreased with the aging time due to an increase in the thickness of interfacial IMC and coarsening of Ag3Sn in the solder. However, higher shear strength exhibited by SAC 305-ZrO2A/Cu joints was attributed to the fine Ag3Sn IMC’s dispersed in the solder matrix. Fracture analysis of SAC 305-ZrO2A/Cu joints displayed mixed solder/IMC mode upon 256 h of aging.

RELIABILITY EVALUATION OF BGA SOLDER JOINTS DURING ACCELERATED LIFE TEST

2006 ◽  
Vol 20 (25n27) ◽  
pp. 4553-4558
Author(s):  
OUK SUB LEE ◽  
NO HOON MYOUNG ◽  
DONG HYEOK KIM ◽  
MAN JAE HUR ◽  
SI WOON HWANG
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Coefficient Of Thermal Expansion ◽  
Accelerated Life Test ◽  
Lead Free ◽  
Lead Free Solder ◽  
Metal Fatigue ◽  
Mechanical Loads ◽  
Free Solder

The use of BGA (Ball Grid Array) interconnects utilizing the lead-free solder joint has grown rapidly because of its small volume and diversity of application. Thus, it requires the continuous quantification and refinement of lead-free solder joint reliability. The lead-free solder creep and cyclically applied mechanical loads cause metal fatigue on the lead-free solder joint which inevitably leads to an electrical discontinuity. In the field application, BGA solder joints experience mechanical loads during temperature changes caused by power up/down events as the result of the CTE (Coefficient of Thermal Expansion) mismatch between the substrate and the Si die. In this paper, extremely small resistance changes at joint area corresponding to through-cracks generated by thermal fatigue were measured. In this way, the failure was defined in terms of anomalous changes in electrical resistance of the joint. Furthermore the reliability of BGA solder joints in thermal cycling is evaluated by using the modified coffin-Manson criterion which may define and distinguish failure. Any change in circuit resistance according to the accumulated damage induced by the thermal cycling in the joint was recorded and evaluated in order to quantitate reliability of solder joint.

Isothermal Aging Affect to the Growth of Sn-Cu-Ni-1 wt.% TiO2 Composite Solder Paste

2016 ◽  
Vol 700 ◽  
pp. 123-131 ◽  
Author(s):  
Rita Mohd Said ◽  
Mohd Arif Anuar Mohd Salleh ◽  
Mohd Nazree Derman ◽  
Mohd Izrul Izwan Ramli ◽  
Norhayanti Mohd Nasir ◽  
...  
Keyword(s):  
Intermetallic Compound ◽  
Solder Joint ◽  
Aging Time ◽  
Isothermal Aging ◽  
Composite Solder ◽  
Solder Paste ◽  
Cu Substrate ◽  
Interfacial Imcs ◽  
Planar Shape ◽  
Interfacial Intermetallic Compound

This work investigated the effects of 1.0 wt. % TiO2 particles addition into Sn-Cu-Ni solder paste to the growth of the interfacial intermetallic compound (IMC) on Cu substrate after isothermal aging. Sn-Cu-Ni solder paste with TiO2 particles were mechanically mixed to fabricate the composite solder paste. The composite solder paste then reflowed in the reflow oven to form solder joint. The reflowed samples were then isothermally aged 75, 125 and 150 ° C for 24 and 240 h. It was found that the morphology of IMCs changed from scallop-shape to a more uniform planar shape in both Sn-Cu-Ni/Cu joints and Sn-Cu-Ni-TiO2 /Cu joint. Cu6Sn5 and Cu3Sn IMC were identified and grew after prolong aging time and temperature. The IMCs thickness and scallop diameter of composite solder paste were reduced and the growth of IMCs thickness after isothermal aging become slower as compared to unreinforced Sn-Cu-Ni solder paste. It is suggested that TiO2 particles have influenced the evolution and retarded the growth of interfacial IMCs.

Performance of 96.5Sn–3Ag–0.5Cu/fullerene composite solder under isothermal ageing and high-current stressing

2020 ◽  
Vol 33 (1) ◽  
pp. 35-46 ◽  
Author(s):  
Guang Chen ◽  
Xinzhan Cui ◽  
Yaofeng Wu ◽  
Wei Li ◽  
Fengshun Wu
Keyword(s):  
Solder Joint ◽  
Composite Solder ◽  
Solder Joints ◽  
Experimental Results ◽  
High Current ◽  
Sac305 Solder ◽  
Content Type ◽  
Interfacial Imcs ◽  
Current Stressing ◽  
Isothermal Ageing

Purpose The purpose of this paper is to investigate the effect of fullerene (FNS) reinforcements on the microstructure and mechanical properties of 96.5Sn3Ag0.5Cu (SAC305) lead-free solder joints under isothermal ageing and electrical-migration (EM) stressing. Design/methodology/approach In this paper, SAC305 solder alloy doped with 0.1 Wt.% FNS was prepared via the powder metallurgy method. A sandwich-like sample and a U-shaped sample were designed and prepared to conduct an isothermal ageing test and an EM test. The isothermal ageing test was implemented under vacuum atmosphere at 150°C, whereas the EM experiment was carried out with a current density of 1.5 × 104 A/cm2. The microstructural and mechanical evolutions of both plain and composite solder joints after thermal ageing and EM stressing were comparatively studied. Findings A growth of Ag3Sn intermetallic compounds (IMCs) in solder matrix and Cu-Sn interfacial IMCs in composite solder joints was notably suppressed under isothermal ageing condition, whereas the hardness and shear strength of composite solder joints significantly outperformed those of non-reinforced solder joints throughout the ageing period. The EM experimental results showed that for the SAC305 solder, the interfacial IMCs formulated a protrusion at the anode after 360 h of EM stressing, whereas the surface of the composite solder joint was relatively smooth. During the stressing period, the interfacial IMC on the anode side of the plain SAC305 solder showed a continuous increasing trend, whereas the IMC at the cathode presented a decreasing trend for its thickness as the stressing time increased; after 360 h of stressing, some cracks and voids had formed on the cathode side. For the SAC305/FNS composite solder, a continuous increase in the thickness of the interfacial IMC was found on both the anode and cathode sides; the growth rate of the interfacial IMC at the anode was higher than that at the cathode. The nanoindentation results showed that the hardness of the SAC305 solder joint presented a gradient distribution after EM stressing, whereas the hardness data showed a relatively homogeneous distribution in the SAC305/FNS solder joint. Originality/value The experimental results showed that the FNS reinforcement could effectively mitigate the failure risk in solder joints under isothermal ageing and high-current stressing. Specifically, the FNS particles in solder joints can work as a barrier to suppress the diffusion and migration of Sn and Cu atoms. In addition, the nanoidentation results also indicated that the addition of the FNS reinforcement was very helpful in maintaining the mechanical stability of the solder joint. These findings have provided a theoretical and experimental basis for the practical application of this novel composite solder with high-current densities.

Sign in / Sign up

Export Citation Format

Share Document