scholarly journals Heat Transfer Enhancement of TiO2/Water Nanofluids Flowing Inside a Square Minichannel with a Microfin Structure: A Numerical Investigation

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3041 ◽  
Author(s):  
Budi Kristiawan ◽  
Agung Tri Wijayanta ◽  
Koji Enoki ◽  
Takahiko Miyazaki ◽  
Muhammad Aziz
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Volume Fraction ◽  
Practical Application ◽  
Transfer Enhancement ◽  
Working Fluids ◽  
Performance Evaluation Criterion ◽  
Developing Flow ◽  
And Performance ◽  
Economic Considerations

A combination of two passive heat transfer enhancement techniques using a microfin structure and nanofluids was investigated numerically. TiO2/water nanofluids flowing inside a square minichannel with a microfin structure (SMM) were observed as a practical application. Increased heat transfer performance was investigated by observing the Nusselt number, friction factor, and performance evaluation criterion (PEC). Velocity and temperature profiles were also demonstrated at a laminar developing flow regime. The SMM used in this work had six microfins (N = 6) and TiO2/water nanofluids with various nanoparticle concentrations of 0.005, 0.01, and 0.1 vol.%. By combining nanofluids as working fluids and SMM as a passive heat transfer enhancement, the maximum PEC value of 1.2 was achieved at Re = 380 with a volume fraction of 0.01 vol.%. It is obvious that compared to water flowing inside the square minichannel microfin, the heat transfer can be increased by using only a nanofluid with a volume fraction of 0.01%. The combination of a microfin and nanofluids as working fluids is strongly recommended due to its excellent performance in terms of heat transfer and economic considerations.

Study of the boundary layer heat transfer of nanofluids over a stretching sheet: Passive control of nanoparticles at the surface

2015 ◽  
Vol 93 (7) ◽  
pp. 725-733 ◽  
Author(s):  
M. Ghalambaz ◽  
E. Izadpanahi ◽  
A. Noghrehabadi ◽  
A. Chamkha
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Heat Transfer Enhancement ◽  
Base Fluid ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Enhancement Ratio ◽  
Transfer Enhancement

The boundary layer heat and mass transfer of nanofluids over an isothermal stretching sheet is analyzed using a drift-flux model. The relative slip velocity between the nanoparticles and the base fluid is taken into account. The nanoparticles’ volume fractions at the surface of the sheet are considered to be adjusted passively. The thermal conductivity and the dynamic viscosity of the nanofluid are considered as functions of the local volume fraction of the nanoparticles. A non-dimensional parameter, heat transfer enhancement ratio, is introduced, which shows the alteration of the thermal convective coefficient of the nanofluid compared to the base fluid. The governing partial differential equations are reduced into a set of nonlinear ordinary differential equations using appropriate similarity transformations and then solved numerically using the fourth-order Runge–Kutta and Newton–Raphson methods along with the shooting technique. The effects of six non-dimensional parameters, namely, the Prandtl number of the base fluid Prbf, Lewis number Le, Brownian motion parameter Nb, thermophoresis parameter Nt, variable thermal conductivity parameter Nc and the variable viscosity parameter Nv, on the velocity, temperature, and concentration profiles as well as the reduced Nusselt number and the enhancement ratio are investigated. Finally, case studies for Al2O3 and Cu nanoparticles dispersed in water are performed. It is found that increases in the ambient values of the nanoparticles volume fraction cause decreases in both the dimensionless shear stress f″(0) and the reduced Nusselt number Nur. Furthermore, an augmentation of the ambient value of the volume fraction of nanoparticles results in an increase the heat transfer enhancement ratio hnf/hbf. Therefore, using nanoparticles produces heat transfer enhancement from the sheet.

scholarly journals Investigation of the novelty of latent functionally thermal fluids as alternative to nanofluids in natural convective flows

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Zoubida Haddad ◽  
Farida Iachachene ◽  
Eiyad Abu-Nada ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Enhancement ◽  
Volume Fraction ◽  
Heat Of Fusion ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Thermal Fluids ◽  
Maximum Heat Transfer ◽  
Wide Range

AbstractThis paper presents a detailed comparison between the latent functionally thermal fluids (LFTFs) and nanofluids in terms of heat transfer enhancement. The problem used to carry the comparison is natural convection in a differentially heated cavity where LFTFs and nanofluids are considered the working fluids. The nanofluid mixture consists of Al2O3 nanoparticles and water, whereas the LFTF mixture consists of a suspension of nanoencapsulated phase change material (NEPCMs) in water. The thermophysical properties of the LFTFs are derived from available experimental data in literature. The NEPCMs consist of n-nonadecane as PCM and poly(styrene-co-methacrylic acid) as shell material for the encapsulation. Finite volume method is used to solve the governing equations of the LFTFs and the nanofluid. The computations covered a wide range of Rayleigh number, 104 ≤ Ra ≤ 107, and nanoparticle volume fraction ranging between 0 and 1.69%. It was found that the LFTFs give substantial heat transfer enhancement compared to nanofluids, where the maximum heat transfer enhancement of 13% was observed over nanofluids. Though the thermal conductivity of LFTFs was 15 times smaller than that of the base fluid, a significant enhancement in thermal conductivity was observed. This enhancement was attributed to the high latent heat of fusion of the LFTFs which increased the energy transport within the cavity and accordingly the thermal conductivity of the LFTFs.

Phase Change Material Particulate Flow Through a Rectangular Channel: Effect of Parachute-Shaped Particles on the Heat Transfer

2011 ◽  
Author(s):  
Laura Small ◽  
Fatemeh Hassanipour
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Phase Change ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Phase Change Material ◽  
Volume Fraction ◽  
Particulate Flow ◽  
Transfer Enhancement ◽  
Change Material

This study presents numerical simulations of forced convection with parachute-shaped encapsulated phase-change material particles in water, flowing through a square cross-section duct with top and bottom iso-flux surfaces. The system is inspired by the gas exchange process in the alveolar capillaries between the red blood cells (RBC) and the lung tissue. The numerical model was developed for the motion of elongated encapsulated phase change particles along a channel in a particulate flow where particle diameters are comparable with the channel height. Results of the heat transfer enhancement for the parachute-shaped particles are compared with the circular particles. Results reveal that the key role in heat transfer enhancement is the snugness movement of the particles and the parachute-shaped geometry yields small changes in heat transfer coefficient when compared to the circular ones. The effects of various parameters including particle diameter and volume-fraction, as well as fluid speed, on the heat transfer coefficient is investigated and reported in this paper.

Laminar Flow and Heat Transfer Characteristics of Colloid Suspensions in Water: A Numerical Study

2009 ◽  
Author(s):  
Khalid N. Alammar ◽  
Lin-wen Hu
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Heat Transfer Enhancement ◽  
Volume Fraction ◽  
Numerical Study ◽  
Volume Flow Rate ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

Numerical analysis is performed to examine axisymmetric laminar flow and heat transfer characteristics of colloidal dispersions of nanoparticles in water (nanofluids). Effect of volume fraction on flow and heat transfer characteristics is investigated. Four different materials, Alumina, Copper, Copper Oxide, and Graphite are considered. Heat transfer and property measurements were conducted previously for Alumina nanofluid. The measurements have shown that nanofluids can behave as homogeneous mixtures. It is found that oxide-based nanofluids offer the least heat transfer enhancement compared to elements-based nanofluids. When normalized by friction pressure drop, it is shown that graphite can have the highest effective heat transfer enhancement. For a given volume flow rate, all nanofluids exhibited linear increase in heat transfer enhancement with increasing colloids volume fraction, up to 0.05.

scholarly journals 3D-printed tubes with complex internal fins for heat transfer enhancement—CFD analysis and performance evaluation

AIMS Energy ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 27-47
Author(s):  
Chao Wei ◽  
◽  
Gabriel Alexander Vasquez Diaz ◽  
Kun Wang ◽  
Peiwen Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Performance Evaluation ◽  
Heat Transfer Enhancement ◽  
Cfd Analysis ◽  
Transfer Enhancement ◽  
3D Printed ◽  
And Performance ◽  
Internal Fins

scholarly journals Experimental and Numerical Study Effect of Using Nanofluids in Perforated Plate Fin Heat Sink for Electronics Cooling

2018 ◽  
Vol 24 (8) ◽  
pp. 1
Author(s):  
Kadhum Audaa Jehhef
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Volume Fraction ◽  
Numerical Study ◽  
Perforated Plate ◽  
Processing Unit ◽  
Transfer Enhancement

An experimental and numerical investigation of the effect of using two types of nanofluids with suspending of (Al2O3 and CuO) nanoparticles in deionized water with a volume fraction of (0.1% vol.), in addition to use three types of fin plate configurations of (smooth, perforated, and dimple plate) to study the heat transfer enhancement characteristics of commercial fin plate heat sink for cooling computer processing unit. All experimental tests under simulated conditions by using heat flux heater element with input power range of (5, 16, 35, 70, and 100 W). The experimental parameters calculated are such as water and nanofluid as coolant with Reynolds number of (7000, 8000, 9400 and 11300); the air is blown in the inlet duct across the heat sink with Reynolds number of (10500, 12300, 14200 and 16000). The distance fin-to-fin is kept constant at (2.00 mm), and the channel employed in this work has a square cross-section of (7 cm) inside. It was observed that the average effectiveness and Nusselt number of the nanofluids are higher compared with those of using conventional liquid cooling systems. However, the perforated fin plate showed higher air heat dissipation than the other configuration plate fin employed in this study. The experimental results were supported by numerical results which gave a good indication to heat transfer enhancement in studied ranges.  

Shape effect of nanoparticles on MHD nanofluid flow over a stretching sheet in the presence of heat source/sink with entropy generation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hamza Berrehal ◽  
G. Sowmya ◽  
Oluwole Daniel Makinde
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heat Transfer Enhancement ◽  
Ag Nanoparticles ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Transfer Enhancement ◽  
Shooting Technique ◽  
Content Type ◽  
Source Sink

Purpose In heat transfer, fluids and nanoparticles can provide new innovative technologies with potential to adapt the heat transfer fluid’s thermal properties through control over particle size, shape and others. This paper aims to examine the effects of spherical and non-spherical (cylinder, disk, platelets, etc.) shapes of silver (Ag) nanoparticles on heat transfer enhancement and inherent irreversibility in hydromagnetic water base nanoliquid flow over a convectively heated stretching sheet with heat generation/absorption. Design/methodology/approach Applying suitable similarity constraints, the model partial differential equations are transformed into a set of nonlinear ordinary differential equations. Solutions are obtained analytically via optimal homotopy asymptotic method (OHAM) and numerically via shooting technique coupled with the Runge-Kutta-Fehlberg (RK-F) method. Findings The impact of Ag nanoparticle’s shape along with other germane factors, such as Biot number, magnetic field, solid volume fraction and heat source/sink on velocity and thermal profiles, Nusselt number, skin friction coefficient, heat transfer enhancement, rate of entropy generation and irreversibility ratio, are scrutinized via graphical simulations and discussed. This study revealed that cylindrical shape Ag nanoparticles generate high entropy and fluid friction irreversibility, whereas disk shape Ag nanoparticles exhibit high transfer enhancement rate. Moreover, a boost in magnetic field intensity, volume-fraction parameter and Biot number enhances the thermal boundary layer thickness. Originality/value The main objective of this work is to examine the different Ag nanoparticles shape effects on the heat transfer enhancement and inherent irreversibility owing to hydromagnetic nanoliquid flow past a convectively heated stretching sheet with heat source/sink, which has not been yet studied. It is hope that this study will bridge the gap in the present literature and serve as impetus to scholars, engineers and industries for more exploration in this direction. The intrinsic nonlinearity of the model equations precludes its exact solution; hence, OHAM and shooting technique coupled with the RK-F method have been used to numerically tackle the problem. Pertinent results are discussed quantitatively and displayed graphically and in tabular form.

Sign in / Sign up

Export Citation Format

Share Document