scholarly journals Design and Analysis of Tubular Slotted Linear Generators for Direct Drive Wave Energy Conversion Systems

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6171
Author(s):  
Naily Akmal Mohd Zamri ◽  
Taib Ibrahim ◽  
Nursyarizal Mohd Nor
Keyword(s):  
Wave Energy ◽  
Attractive Alternative ◽  
Direct Drive ◽  
Element Analysis ◽  
Split Ratio ◽  
Tooth Width ◽  
Vertical Speed ◽  
Energy Conversion Systems ◽  
Pitch Ratio ◽  
Main Dimension

Linear generator utilization in a wave energy converter (WEC) is an attractive alternative to a rotary generator. This paper presents the design of a permanent magnet linear machine (PMLM) for WEC applications in low wave power areas. In this paper, the wave height and vertical speed of Malaysian water is used for the simulation and design. Two design variants are introduced which are tubular PMLM with no spacer (TPMLM-NS) and tubular PMLM with spacer (TPMLM-S). Finite element analysis (FEA) has been conducted to investigate the performance and to refine the main dimensions of the design in terms of split ratio, pitch ratio and tooth width. The FEA results are then validated using an analytical method which is established according to the design’s magnetic field distribution. Based on main dimension refinement, it can be deduced that both the split ratio and the pitch ratio have a significant influence on the airgap flux density and back EMF of the design. The obtained FEA results also reveal that the TPMLM-NS variant is capable of producing 240 V back EMF, 1 kW output power with satisfactory efficiency. Consequently, this indicates the capability of the design to convert wave energy with good performance. Additionally, good agreement between the analytical predictions and FEA results was obtained with a low percentage of error, thus providing concrete assurance of the accuracy of the design.

scholarly journals High-performance magneto-rheological clutches for direct-drive actuation: Design and development

2021 ◽  
pp. 1045389X2110069
Author(s):  
Sergey Pisetskiy ◽  
Mehrdad Kermani
Keyword(s):  
High Performance ◽  
Degrees Of Freedom ◽  
Dynamic Range ◽  
Complete Analysis ◽  
Mass Ratio ◽  
Direct Drive ◽  
Element Analysis ◽  
Prototype Development ◽  
Magneto Rheological ◽  
Hall Sensors

This paper presents an improved design, complete analysis, and prototype development of high torque-to-mass ratio Magneto-Rheological (MR) clutches. The proposed MR clutches are intended as the main actuation mechanism of a robotic manipulator with five degrees of freedom. Multiple steps to increase the toque-to-mass ratio of the clutch are evaluated and implemented in one design. First, we focus on the Hall sensors’ configuration. Our proposed MR clutches feature embedded Hall sensors for the indirect torque measurement. A new arrangement of the sensors with no effect on the magnetic reluctance of the clutch is presented. Second, we improve the magnetization of the MR clutch. We utilize a new hybrid design that features a combination of an electromagnetic coil and a permanent magnet for improved torque-to-mass ratio. Third, the gap size reduction in the hybrid MR clutch is introduced and the effect of such reduction on maximum torque and the dynamic range of MR clutch is investigated. Finally, the design for a pair of MR clutches with a shared magnetic core for antagonistic actuation of the robot joint is presented and experimentally validated. The details of each approach are discussed and the results of the finite element analysis are used to highlight the required engineering steps and to demonstrate the improvements achieved. Using the proposed design, several prototypes of the MR clutch with various torque capacities ranging from 15 to 200 N·m are developed, assembled, and tested. The experimental results demonstrate the performance of the proposed design and validate the accuracy of the analysis used for the development.

Analysis of a Tubular Linear Permanent Magnet Motor for Reciprocating Compressor Applications

2013 ◽  
Vol 448-453 ◽  
pp. 2114-2119 ◽  
Author(s):  
Izzeldin Idris Abdalla ◽  
Taib Ibrahim ◽  
Nursyarizal Mohd Nor
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnets ◽  
Outer Radius ◽  
Design Parameters ◽  
Reciprocating Compressor ◽  
Permanent Magnet Motors ◽  
Permanent Magnet Motor ◽  
Element Analysis ◽  
Split Ratio ◽  
Single Coil

This paper describes a design optimization to achieve optimal performance of a two novel single-phase short-stroke tubular linear permanent magnet motors (TLPMMs) with rectangular and trapezoidal permanent magnets (PMs) structures. The motors equipped with a quasi-Halbach magnetized moving-magnet armature and slotted stator with a single-slot carrying a single coil. The motors have been developed for reciprocating compressor applications such as household refrigerators. It is observed that the TLPMM efficiency can be optimized with respect to the leading design parameters (dimensional ratios). Furthermore, the influence of mover back iron is investigated and the loss of the motor is computed. Finite element analysis (FEA) is employed for the optimization, and the optimal values of the ratio of the axial length of the radially magnetized magnets to the pole pitch as well as the ratio of the PMs outer radius-to-stator outer radius (split ratio), are identified.

Coupled Electromagnetic and Lattice Structure Optimization for the Rotor and Stator of Large Electric Machines

2021 ◽  
Author(s):  
Austin C. Hayes ◽  
Gregory L. Whiting
Keyword(s):  
Wind Turbine ◽  
Lattice Structure ◽  
Electric Machines ◽  
Force Density ◽  
Direct Drive ◽  
Element Analysis ◽  
Electromagnetic Design ◽  
Turbine Generators ◽  
Wind Turbine Generators ◽  
Structural Mass

Abstract Permanent magnet direct drive (PMDD) electric machines are advantageous due to higher efficiencies and lower maintenance concerns. For wind turbine generators, especially offshore turbines, this is advantageous to geared machines and is currently implemented by manufacturers such as GE, Siemens and Enercon. By nature, a direct drive machine must be larger than its geared counterpart in order to output the same power. As a result, the structural mass is larger and makes the machine prohibitively large. However, the structural mass and electromagnetic design is coupled and the electromagnetic criteria are an important consideration in the structural design. In this analysis, the electromagnetic design of a 5 MW PMDD generator was coupled to a triply periodic minimal surface (TPMS) lattice generator through means of an evolutionary algorithm. Finite element analysis (FEA) was used to determine the radial, torsional, and axial deformations under simulated wind turbine generator loading conditions subject to critical deflection criteria. Lattice functional grading was completed with the FEA deflection data in order to further optimize the structural mass. For the 5 MW test case, functional graded TPMS support structures maintained stiffness for a generator with a 32% higher force density with inactive mass 4% lower than baseline. This study suggests functional grading of TPMS lattice structures for wind turbine generators has the potential at significant mass savings.

Power Conditioning Unit for Direct-Drive Wave Energy Converter

2018 ◽  
Author(s):  
Yuriy Rozanov ◽  
Konstantin Kryukov ◽  
Mikhail Kiselev ◽  
Mikhail Lepanov ◽  
Yuriy Tserkovsky ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Direct Drive ◽  
Power Conditioning ◽  
Energy Converter
Sign in / Sign up

Export Citation Format

Share Document