scholarly journals Studies of the Impact of Hydrogen on the Stability of Gaseous Mixtures of THT

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6441
Author(s):  
Anna Huszal ◽  
Jacek Jaworski

One of the most important requirements concerning the quality of natural gases, guaranteeing their safe use, involves providing the proper level of their odorization. This allows for the detection of uncontrolled leakages of gases from gas networks, installations and devices. The concentration of an odorant should be adjusted in such a manner that the gas odor in a mixture with air would be noticeable by users (gas receivers). A permanent odor of gas is guaranteed by the stability of the odorant molecule and its resistance to changes in the composition of odorized gases. The article presents the results of experimental research on the impact of a hydrogen additive on the stability of tetrahydrothiophene (THT) mixtures in methane and in natural gas with a hydrogen additive. The objective of the work was to determine the readiness of measurement infrastructures routinely used in monitoring the process of odorizing natural gas for potential changes in its composition. One of the elements of this infrastructure includes the reference mixtures of THT, used to verify the correctness of the readings of measurement devices. The performed experimental tests address possible changes in the composition of gases supplied via a distribution network, resulting from the introduction of hydrogen. The lack of interaction between hydrogen and THT has been verified indirectly by assessing the stability of its mixtures with methane and natural gas containing hydrogen. The results of the presented tests permitted the identification of potential hazards for the safe use of gas from a distribution network, resulting from changes in its composition caused by the addition of hydrogen.

Author(s):  
O. Maistrenko ◽  
O. Karavanov ◽  
A. Shcherba

It is established that the role of reconnaissance and fire systems in the implementation of enemy fire damage in military conflicts occurring at the beginning of the XXI century. Increased  to 75%. However, it was found that the effectiveness of these systems depends on the quality of their equipment. The main factors that are often not taken into account in the acquisition are the possibility, interoperability, stability of each element, the impact of elements on the stability of each other and the functioning of the RVS as a whole. The analysis of recent research and publications has shown that as of today, the approaches to determining the composition of reconnaissance fire systems taking into account these factors are not justified. Given the above, it was decided to conduct a structural and functional analysis of the reconnaissance fire system and the decomposition of its functions and subsystems. To this end, based on the method of cluster analysis, an algorithm for combining a set of tasks performed by reconnaissance and fire systems into groups has been developed and substantiated. The method of expert evaluation was used to obtain substantiated data on the implementation of such a merger. According to the proposed algorithm, the main tasks were first identified, which involve reconnaissance and fire systems. Subsequently, an expert group was formed and the coefficient of relative competence of each member of the expert group was determined. The experts were then asked to combine the identified tasks according to their characteristics into an arbitrary number of groups. After processing the opinions of experts, 10 characteristic groups were identified. Finally, the experts were asked to combine the obtained groups in such a way that each association consisted of similar objects and the objects of different associations differed significantly. The results of the work revealed the functional interconnectedness of the tasks, processes and subsystems of the reconnaissance and fire system. It is also established that a typical reconnaissance fire system will consist of three subsystems (control, reconnaissance and fire influence), which perform specific functions for each of them.


2012 ◽  
Vol 57 (2) ◽  
pp. 351-362 ◽  
Author(s):  
Mariusz Łaciak

Abstract The increase in natural gas consumption by the general public and industry development, in particular the petrochemical and chemical industries, has made increasing the world interest in using gas replacement for natural gas, both as mixtures of flammable gases and gas mixtures as LPG with air (SNG - Synthetic Natural Gas). Economic analysis in many cases prove that to ensure interchangeability of gas would cost less than the increase in pipeline capacity to deliver the same quantity of natural gas. In addition, SNG systems and installations, could be considered as investments to improve security and flexibility of gas supply. Known existing methods for determining the interchangeability of gases in gas gear based on Wobbe index, which determines the heat input and the burning rate tide, which in turn is related to flame stability. Exceeding the Wobbe index of a value increases the amount of carbon monoxide in the exhaust than the permissible concentration. Methods of determining the interchangeability of gases is characterized by a gas in relation to the above-described phenomena by means of quantitative indicators, or using diagrams interchangeability, where the gas is characterized by the position of a point in a coordinate system. The best known method for determining the interchangeability of gases is Delbourg method, in which the gas is characterized by the revised (expanded) Wobbe Index (Wr), the combustion potential, rate of soot formation (Ich) and the ratio of the formation of yellow ends (Ij). Universal way to determine the interchangeability of gas is also Weaver accounting method. It does not require determination of the reference gas. It is designed for utensils for household gas and gas pressure p = 1.25 kPa. The criteria and definition of gas interchangeability volatility in practice to the combustion in a gas gear. In the case of gas exchange in industrial furnaces, interchangeability criteria are usually not very useful because of other conditions of combustion and heat exchange. In industrial reheating furnace gas is combusted in a sealed combustion chambers. Air supply is regulated. The exhaust gases are discharged into canals and the chimney to the atmosphere. The temperature difference between load (fuel gas) and the flame is much less than in the case of gas household appliances. In the furnace heat exchange takes place mainly by radiation in 85% to 95%. The value of heat flux flowing from the gas to a heated charge is not proportional to the heat load burners. Interchangeability of gas is linked by adding to natural gas, a certain amount of gas that is a substitute for natural gas in meeting the criteria for substitution in order to ensure certainty of supply of natural gas to customers. Gases that can be used in the processes of blending and used as replacement gases are mainly a mixture of propane and propane - butane (LPG - Liquid Petroleum Gas), landfill gas or biogas (LFG - Landfill Gas) and dimethyl ether (DME). One of the more well-known gas mixtures used in many countries around the world to compensate for peak demands is a mixture containing about 75% of natural gas and approximately 25% propane / air (LPG / air). Also in Poland is prepared to amend the provisions in this regard (at this moment - oxygen in the gas network can not exceed 0.2%). In this paper, the calculations of interchangeability of gas mixtures LFG - LPG and LPG - air (SNG) for natural gas was made. It was determined whether the analyzed mixtures have similar stable flame zones regardless of the quality of LFG fuel and whether they may in whole or in part replace CH4, without any modification of equipment suction air for combustion. The obtained results will determine whether the fuel can be used as a replacement for natural gas used in such household appliances and, possibly, industrial burners. In connection with the possibility of changes in the quality of LFG, depending on such factors as storage time, as pre-treatment, will be determined the degree of interchangeability of LFG as a fuel mixed with regard to its quality.


2013 ◽  
Vol 315 ◽  
pp. 552-556 ◽  
Author(s):  
Shahrul Azmir Osman ◽  
Ahmad Jais Alimin ◽  
V.S. Liong

The use of natural gas as an alternative fuels are motivated from the impact in deteriorating quality of air and the energy shortage from petroleum products. Through retrofitting, CI engine runs on CNG, will be able to reduce the negative impact mainly on the use of petroleum products. However, this required the modification of the combustion chamber geometry by reducing the compression ratio to value that suits combustion of CNG. In this present studies, four different shapes and geometries of combustion chamber were designed and simulate using CFD package powered by Ansys workbench, where k-ε turbulence model was used to predict the flow in the combustion chamber. The results of turbulence kinetic energy, velocity vectors and streamline are presented. The enhancement of air-fuel mixing inside the engine cylinder can be observed, where the design with re-entrance and lower center projection provide better results compared to other combustion geometries designs.


Author(s):  
M. C. Fernández-Feal ◽  
B. Sánchez-Fernández ◽  
L. R. Sánchez-Fernández ◽  
J. R. Pérez-Prado

Aims: To assess the composition of the Natural Gas (NG) supplied for domestic consumption through the distribution network to correlate the physical properties linked to it were to be determined in order to investigate their fluctuations. Study Design:  The samples were analyzed in accordance with the method described in the ISO 6974‑4 standard, “Natural Gas. Determination of Composition with Defined Uncertainty by Gas Chromatography”. Place and Duration of Study: Center of Technology Research, Fuels Laboratory, between January and December 2016. Methodology: Over the course of the year, a total of eighty-four samples of natural gas for domestic use were analyzed.  These were collected at a rate of one per month in seven cities in the geographical zone under study (Galicia_Spain), in which the number of users is significant. Results and Conclusion: The protocols for technical management of the Gas System have a section on quality specifications for Natural Gas at entry points to the system.  This sets limits for only three of the physical properties of natural gas: Wobbe index, superior calorific value and relative density. The figures obtained for Wobbe index, superior calorific value and relative density from the eighty-four samples studied showed that the quality of the Natural Gas distributed remained steadily within the acceptable limits throughout the whole year. The values for standard deviations bore witness to the fact that any variations did not significantly alter the quality of the Natural Gas supplied. The concentrations of the odorant, THT, were always above the recommended value of 18.0 mg/Nm3, the fluctuations noted over the course of the year were such as to make it possible to see them as excessive. In some instances, a high concentration of odorant may lead users to erroneous impressions, so that they come to think that there are leaks from the gas-pipes or even that the gas is not burning properly.


2021 ◽  
pp. 81-90
Author(s):  
Alexey Semenovich Dorokhov ◽  
Andrey Grigoryevich Ponomarev ◽  
Vitaly Nikolaevich Zernov ◽  
Sergey Nikolaevich Petukhov ◽  
Alexander Gennadievich Aksenov ◽  
...  

Structural layouts of coulters and their groups in potato planters are justified in the article based on the morphological features of the potato plant, its requirements for growing conditions and ensuring the quality of the planting process. The purpose of coulter groups is to form a bed for placing tubers with a loose layer of soil in 5-8 cm and sealing them with loosened soil to a certain depth. To substantiate the type of potato planter coulters that meet the requirements for potato growing conditions to the maximum extent possible, optimize the parameters of coulter groups that automatically ensure the stability of the coulter travel depth when imitating irregularities of the field microrelief. A comparative analysis of the impact on the soil of the most common anchor coulters with a blunt angle of soil entry and a sharp angle with an individual floating suspension is given, and indicators of the quality of their operation are described. It was found that coulters with an individual floating suspension and an acute angle of soil entry meet the requirements for potato growing conditions to the maximum extent possible. In order to ensure travel stabilization of such a coulter at a given depth when imitating field irregularities, a version of the coulter group has been developed that provides automatic correction of the coulter's angle of attack when changing its travel depth. Experimental studies have optimized the parameters of the coulter suspension that ensure automatic imitation of field microrelief irregularities up to 20 cm deep within the initial requirements for potato planting machines. Coulters with an individual floating suspension and a sharp angle of soil entry most fully meet the requirements for potato growing conditions to the maximum extent possible. A coulter group with a suspension aspect ratio of 150:200:400:400 cm and an acute angle of coulter entry into the soil provides automatic maintenance of the set coulter travel depth within the initial requirements (±2 cm) for irregularities in the field microrelief of up to 200 mm. In this case, the bottom and walls of the furrow are not compacted.


Author(s):  
Jekaterina Porubova ◽  
Marco Klemm ◽  
Isabel Kiendl ◽  
Karlis Valters ◽  
Darja Markova ◽  
...  

Abstract Energy plans of many countries anticipate an increased use of biomethane for energy supply, i.e., in power and heat production as well as in the transport sector. Existing infrastructure of natural gas storage, supply and application provides a good platform to facilitate transfer to biomethane utilization on a larger scale. One key element of the biomethane system is the upgrade of the biomass-derived synthesis gas originating from different sources, to a quality of natural gas (SNG - Synthesis Natural Gas) via the methanation process for further injection into the natural gas grid.. The maximisation of efficiency of the methanation process is of critical importance in order to make biomethane technology viable for wider application. The aim of the study was to improve efficiency of the methanation process by finding the optimum temperatures and pressure. Theoretical modelling of adiabatic and isothermal methanation processes by using thermodynamic equilibrium calculations was introduced as a method for the study. The results show the impact of temperature and pressure changes on the overall efficiency of methane production. It can be concluded from the study that knowledge about the relation between temperature, pressure and the efficiency of the methanation process makes it possible to optimize the process under various biomass synthesized gas input conditions.


2013 ◽  
Vol 380-384 ◽  
pp. 2999-3002
Author(s):  
Di Wu ◽  
Qi Jun Wu ◽  
Rong Zhao Zhu

To improve the stability and output voltage quality of inverter, an new repetitive control strategy for 400Hz Constant Voltage Constant Frequency (CVCF) inverter has been proposed . Based on active damping, this strategy damps the oscillations on the output LC filter of inverter under unload or light load. Using state-observer to weaken the impact of time delay in digital control, a 5.5 kW one-phase 400Hz inverter prototype by this strategy has been tested.The result shows that low THD (about 1.5%) with inductive loads and fast error convergence (2 fundamental periods) can be achieved by this strategy which can be demonstrated to be brief and effective.


Author(s):  
Adrian P. Defante ◽  
Cavan K. Kalonia ◽  
Emma Keegan ◽  
Steven M. Bishop ◽  
Hasige A. Satish ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document