scholarly journals Simulation of Coupled Power and Gas Systems with Hydrogen-Enriched Natural Gas

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7680
Author(s):  
Yifei Lu ◽  
Thiemo Pesch ◽  
Andrea Benigni

Due to the increasing share of renewable energy sources in the electrical network, the focus on decarbonization has extended into other energy sectors. The gas sector is of special interest because it can offer seasonal storage capacity and additional flexibility to the electricity sector. In this paper, we present a new simulation method designed for hydrogen-enriched natural gas network simulation. It can handle different gas compositions and is thus able to accurately analyze the impact of hydrogen injections into natural gas pipelines. After describing the newly defined simulation method, we demonstrate how the simulation tool can be used to analyze a hydrogen-enriched gas pipeline network. An exemplary co-simulation of coupled power and gas networks shows that hydrogen injections are severely constrained by the gas pipeline network, highlighting the importance and necessity of considering different gas compositions in the simulation.

Author(s):  
Kaituo Jiao ◽  
Peng Wang ◽  
Yi Wang ◽  
Bo Yu ◽  
Bofeng Bai ◽  
...  

The development of natural gas pipeline network towards larger scale and throughput has urged better reliability of the pipeline network to satisfy transportation requirement. Previously, studies of optimizing natural gas pipeline network have been mainly focused on reducing operating cost, with little concern on the reliability of pipeline network. For a natural gas pipeline network with a variety of components and complicated topology, a multi-objective optimization model of both reliability and operating cost is proposed in this study. Failure of each component and the state of pipeline network under failure conditions are taken into account, and minimum cut set method is employed to calculate the reliability of the pipeline network. The variables to be determined for the optimization objectives are the rotating speed of compressors and the opening of valves. Then the solving procedure of the proposed model is presented based on Decoupled Implicit Method for Efficient Network Simulation (DIMENS) method and NS-saDE algorithm. The validity of the optimization model is ascertained by its application on a complicated pipeline network. The results illustrate that the optimization model can depict the relative relationship between reliability and operating cost for different throughput, by which the operation scheme with both satisfying reliability and operating cost can be obtained. In addition, the customer reliability and the impact of the failure of each pipeline on the whole network can be evaluated quantitatively to identify the consumers and pipelines of maintenance priority. The pipeline network reliability can be improved through proper monitoring and maintenance of these consumers and pipelines.


Author(s):  
Francis Bainier ◽  
Rainer Kurz ◽  
Philippe Bass

Abstract Gas Transmission System Operators (TSO1) are considering injecting hydrogen gas into their networks. Blending hydrogen into the existing natural gas pipeline network appears to be a strategy for storing and delivering renewable energy to markets [1], [2], [3]. In the paper GT2019-90348 [4], the authors have explored the efficiency of H2-blending in a natural gas pipeline network. The conclusion of the paper is: the energy transmission capacity and the efficiency decrease with the introduction of H2, nevertheless, the authors conclude that it is not an obstacle, but the way of using transmission natural gas networks should be closely studied to find an economic optimum, based both on capital and operating expenses. To establish the comparison, the paper did not take into account the limits of the equipment; all equipment was considered as compatible with any load of hydrogen blending. In the current paper, the idea is to consider the hypothesis that the only factor which has impact on the infrastructure is the partial pressure of H2. The idea is not new, in 1802, Dalton published a law called Dalton’s Law of Partial Pressures [5]. Dalton established empirically that the total pressure of a mixture of gases is equal to the sum of the partial pressures of the individual component gases. The partial pressure is the pressure that each gas would exert when it alone occupied the volume of the mixture at the same temperature. Independent of the limits of the equipment, the authors explore the relationships between a network capacity and its associated pressures in regards to the H2 partial pressure. Within the partial pressure constraint, the goal is to find the maximum H2 flowrate. This flowrate is then compared with a flowrate which is a function of % H2. Nevertheless, steel is subjected to hydrogen invasion while being exposed to hydrogen containing environments during mechanical loading: resulting in hydrogen embrittlement (HE). HE also depends on the textured microstructure. In the final results [6] [7], the measured fatigue data reveals that the fatigue life of steel pipeline is degraded by the added hydrogen. The H2 has an effect on the steel fatigue which is not simply due to the partial pressure. The idea of the authors through the results of their 2 papers is to give the key points to help to find the optimum points for introducing H2 into a natural gas network, because, for them, the idea is that partial pressure is a factor in the equilibrium between H2 capacity and the remaining lifetime of the equipment. This paper shows the interest of the pressure management. With this management, it is possible to reach a constant H2 injection flow independently of the natural gas flow in the pipeline. In conclusion, to optimize the H2 capacity in their current network, a proposal to the TSOs is to adjust their dispatching methodology and their Pipeline Integrity Management (PIM) [8] [9].


Author(s):  
Aleksandar Tomic ◽  
Shahani Kariyawasam

A lethality zone due to an ignited natural gas release is often used to characterize the consequences of a pipeline rupture. A 1% lethality zone defines a zone where the lethality to a human is greater than or equal to 1%. The boundary of the zone is defined by the distance (from the point of rupture) at which the probability of lethality is 1%. Currently in the gas pipeline industry, the most detailed and validated method for calculating this zone is embodied in the PIPESAFE software. PIPESAFE is a software tool developed by a joint industry group for undertaking quantitative risk assessments of natural gas pipelines. PIPESAFE consequence models have been verified in laboratory experiments, full scale tests, and actual failures, and have been extensively used over the past 10–15 years for quantitative risk calculations. The primary advantage of using PIPESAFE is it allows for accurate estimation of the likelihood of lethality inside the impacted zone (i.e. receptors such as structures closer to the failure are subject to appropriately higher lethality percentages). Potential Impact Radius (PIR) is defined as the zone in which the extent of property damage and serious or fatal injury would be expected to be significant. It corresponds to the 1% lethality zone for a natural gas pipeline of a certain diameter and pressure when thermal radiation and exposure are taken into account. PIR is one of the two methods used to identify HCAs in US (49 CFR 192.903). Since PIR is a widely used parameter and given that it can be interpreted to delineate a 1% lethality zone, it is important to understand how PIR compares to the more accurate estimation of the lethality zones for different diameters and operating pressures. In previous internal studies, it was found that PIR, when compared to the more detailed measures of the 1% lethality zone, could be highly conservative. This conservatism could be beneficial from a safety perspective, however it is adding additional costs and reducing the efficiency of the integrity management process. Therefore, the goal of this study is to determine when PIR is overly conservative and to determine a way to address this conservatism. In order to assess its accuracy, PIR was compared to a more accurate measure of the 1% lethality zone, calculated by PIPESAFE, for a range of different operating pressures and line diameters. Upon comparison of the distances calculated through the application of PIR and PIPESAFE, it was observed that for large diameters pipelines the distances calculated by PIR are slightly conservative, and that this conservativeness increases exponentially for smaller diameter lines. The explanation for the conservatism of the PIR for small diameter pipelines is the higher wall friction forces per volume transported in smaller diameter lines. When these higher friction forces are not accounted for it leads to overestimation of the effective outflow rate (a product of the initial flow rate and the decay factor) which subsequently leads to the overestimation of the impact radius. Since the effective outflow rate is a function of both line pressure and diameter, a simple relationship is proposed to make the decay factor a function of these two variables to correct the excess conservatism for small diameter pipelines.


Author(s):  
Z. Joe Zhou ◽  
Bill Liu ◽  
Gregg O’Neil ◽  
Moness Rizkalla

TransCanada Pipelines Ltd. (TransCanada) operates approximately 37,000 km of natural gas gathering and transmission pipelines. Within the Alberta portion of this system there are almost 1100 locations where the pipeline(s) traverse slopes, primarily as the line approaches and exits stream crossings. In the past, the approach to managing the impact of slope movements on pipeline integrity has been reactive; site investigations and/or monitoring programs would only be initiated once the slope movements were sufficiently large so as to easily observe cracking or scarp development. In some cases these movements could lead to a pipeline rupture. To move to a proactive hazard management approach and to optimize the maintenance expenditure, TransCanada has developed a new slope assessment methodology. The objective of this methodology is to establish a risk-ranked list of slopes upon which maintenance decisions can be based. Using only internal and public information on site conditions as input to predictive models for rainfall-ground movement and pipe-soil interaction, a probability of pipeline failure can be generated for each slope. Estimates of risk using a consequence-matrix approach enabled the compilation of a risk-ranked list of hazardous slopes. This paper describes this methodology, and its implementation at TransCanada, and presents some of the results.


Author(s):  
Yue Xiang ◽  
Peng Wang ◽  
Bo Yu ◽  
Dongliang Sun

The numerical simulation efficiency of large-scale natural gas pipeline network is usually unsatisfactory. In this paper, Graphics Processing Unit (GPU)-accelerated hydraulic simulations for large-scale natural gas pipeline networks are presented. First, based on the Decoupled Implicit Method for Efficient Network Simulation (DIMENS) method, presented in our previous study, a novel two-level parallel simulation process and the corresponding parallel numerical method for hydraulic simulations of natural gas pipeline networks are proposed. Then, the implementation of the two-level parallel simulation in GPU is introduced in detail. Finally, some numerical experiments are provided to test the performance of the proposed method. The results show that the proposed method has notable speedup. For five large-scale pipe networks, compared with the well-known commercial simulation software SPS, the speedup ratio of the proposed method is up to 57.57 with comparable calculation accuracy. It is more inspiring that the proposed method has strong adaptability to the large pipeline networks, the larger the pipeline network is, the larger speedup ratio of the proposed method is. The speedup ratio of the GPU method approximately linearly depends on the total discrete points of the network.


2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Alexandros I. Nikolaidis ◽  
Francisco M. Gonzalez-Longatt ◽  
C. A. Charalambous

The continuous increase on the penetration levels of Renewable Energy Sources (RESs) in power systems has led to radical changes on the design, operation, and control of the electrical network. This paper investigates the influence of these changes on the operation of a transmission network by developing a set of indices, spanning from power losses to GHG emissions reduction. These indices are attempting to quantify any impacts therefore providing a tool for assessing the RES penetration in transmission networks, mainly for isolated systems. These individual indices are assigned an analogous weight and are mingled to provide a single multiobjective index that performs a final evaluation. These indices are used to evaluate the impact of the integration of RES into the classic WSCC 3-machine, 9-bus transmission network.


Sign in / Sign up

Export Citation Format

Share Document