Linear model analysis of fused deposition modeling process parameters for obtaining the maximum tensile strength in acrylonitrile butadiene styrene (ABS) and carbon fiber polylactic acid (PLA) materials

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Debashis Mishra ◽  
Anil Kumar Das
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Layer Thickness ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Thermoplastic Material ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Speed

PurposeThe purpose of the experimental investigation was to optimize the process parameters of the fused deposition modeling (FDM) technique. The optimization of the process was performed to identify the relationship between the chosen factors and the tensile strength of acrylonitrile butadiene styrene (ABS) and carbon fiber polylactic acid (PLA) thermoplastic material, FDM printed specimens. The relationship was demonstrated by using the linear experimental model analysis, and a prediction expression was established. The developed prediction expression can be used for the prediction of tensile strength of selected thermoplastic materials at a 95% confidence level.Design/methodology/approachThe Taguchi L9 experimental methodology was used to plan the total number of experiments to be performed. The process parameters were chosen as three at three working levels. The working range of chosen factors was the printing speed (60, 80 and 100mm/min), 40%, 60% and 80% as the infill density and 0.1mm, 0.2mm and 0.3mm as the layer thickness. The fused deposition modeling process parameters were optimized to get the maximum tensile strength in FDM printed ABS and carbon fiber PLA thermoplastic material specimens.FindingsThe optimum condition was achieved by the process optimization, and the desired results were obtained. The maximum desirability was achieved as 0.98 (98%) for the factors, printing speed 100mm/min, infill density 60mm and layer thickness 0.3mm. The strength of the ABS specimen was predicted to be 23.83MPa. The observed strength value was 23.66MPa. The maximum desirability was obtained as 1 (100%) for the factors, printing speed 100mm/min, infill density 60mm and layer thickness 0.2mm. The strength of the carbon fiber PLA specimen was predicted to be 26.23MPa, and the obtained value was 26.49MPa.Research limitations/implicationsThe research shows the useful process parameters and their suitable working conditions to print the tensile specimens of the ABS and carbon fiber PLA thermoplastics by using the fused deposition modeling technique. The process was optimized to identify the most influential factor, and the desired optimum condition was achieved at which the maximum tensile strength was reported. The produced prediction expression can be used to predict the tensile strength of ABS and carbon fiber PLA filaments.Practical implicationsThe results obtained from the experimental investigation are useful to get an insight into the FDM process and working limits to print the parts by using the ABS and carbon fiber PLA material for various industrial and structural applications.Social implicationsThe results will be useful in choosing the suitable thermoplastic filament for the various prototyping and structural applications. The products that require freedom in design and are difficult to produce by most of the conventional techniques can be produced at low cost and in less time by the fused deposition modeling technique.Originality/valueThe process optimization shows the practical exposures to state an optimum working condition to print the ABS and carbon fiber PLA tensile specimens by using the FDM technique. The carbon fiber PLA shows better strength than ABS thermoplastic material.

scholarly journals Preparation of Hydrophobic Surface on PLA and ABS by Fused Deposition Modeling

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1539 ◽  
Author(s):  
Huadong Yang ◽  
Fengchao Ji ◽  
Zhen Li ◽  
Shuai Tao
Keyword(s):  
Surface Roughness ◽  
Layer Thickness ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Hydrophobic Coatings ◽  
Fused Deposition ◽  
Filling Method ◽  
Deposition Modeling ◽  
Experiment Analysis ◽  
Printing Speed

In the fields of agriculture, medical treatment, food, and packaging, polymers are required to have the characteristics of self-cleaning, anti-icing, and anti-corrosion. The traditional preparation method of hydrophobic coatings is costly and the process is complex, which has special requirements on the surface of the part. In this study, fused deposition modeling (FDM) 3D printing technology with design and processing flexibility was applied to the preparation of hydrophobic coatings on polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) parts, and the relationship between the printing process parameters and the surface roughness and wettability of the printed test parts was discussed. The experimental results show that the layer thickness and filling method have a significant effect on the surface roughness of the 3D-printed parts, while the printing speed has no effect on the surface roughness. The orthogonal experiment analysis method was used to perform the wettability experiment analysis, and the optimal preparation process parameters were found to be a layer thickness of 0.25 mm, the Grid filling method, and a printing speed of 150 mm/s.

scholarly journals Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

2020 ◽  
Vol 5 (1) ◽  
pp. 8
Author(s):  
Arivazhagan Selvam ◽  
Suresh Mayilswamy ◽  
Ruban Whenish ◽  
Rajkumar Velu ◽  
Bharath Subramanian
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Layer Thickness ◽  
Shell Thickness ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Thermoplastic Composites ◽  
Critical Parameters ◽  
Fused Deposition ◽  
Deposition Modeling

The most common method to fabricate both simple and complex structures in the additive manufacturing process is fused deposition modeling (FDM). Many researchers have studied the strengthening of FDM components by adding short carbon fibers (CF) or by reinforcing solid carbon fiber rods. In the current research, we sought to enhance the mechanical properties of FDM components by adding bioinspired solid CF rods during the fabrication process. An effective bonding interface of bioinspired CF rods and polylactic acid (PLA) was achieved by triangular interlocking sutures and by employing synthetic glue as the binding agent. In particular, the tensile strength of solid CF rod reinforced PLA samples was studied. Critical parameters such as layer thickness, extruder temperature, extruder speed, and shell thickness were considered for optimization. Significant process parameters were identified through leverage plots using the response surface methodology (RSM). The optimum parameters were found to be layer thickness of 0.04 mm, extruder temperature of 215 °C, extruder speed of 60 mm/s, and shell thickness of 1.2 mm. The results revealed that the bioinspired solid CF rod reinforced PLA (CFRPLA) composite exhibited a tensile strength of 82.06 MPa, which was approximately three times higher than the pure PLA (28 MPa, 66% lower than CFRPLA), acrylonitrile butadiene styrene (ABS) (28 MPa, 66% lower than CFRPLA), polyethylene terephthalate glycol (PETG) (34 MPa, 60% lower than CFRPLA), and nylon (34 MPa, 60% lower than CFRPLA) samples.

Effect of process parameters on flexural strength and surface roughness in fused deposition modeling of PC-ABS material

2021 ◽  
pp. 251659842110311
Author(s):  
Shrikrishna Pawar ◽  
Dhananjay Dolas1
Keyword(s):  
Surface Roughness ◽  
Flexural Strength ◽  
Response Surface ◽  
Layer Thickness ◽  
Process Parameters ◽  
Surface Finish ◽  
Fused Deposition Modeling ◽  
Build Orientation ◽  
Fused Deposition ◽  
Deposition Modeling

Fused deposition modeling (FDM) is one of the most commonly used additive manufacturing (AM) technologies, which has found application in industries to meet the challenges of design modifications without significant cost increase and time delays. Process parameters largely affect the quality characteristics of AM parts, such as mechanical strength and surface finish. This article aims to optimize the parameters for enhancing flexural strength and surface finish of FDM parts. A total of 18 test specimens of polycarbonate (PC)-ABS (acrylonitrile–butadiene–styrene) material are printed to analyze the effect of process parameters, viz. layer thickness, build orientation, and infill density on flexural strength and surface finish. Empirical models relating process parameters with responses have been developed by using response surface regression and further analyzed by analysis of variance. Main effect plots and interaction plots are drawn to study the individual and combined effect of process parameters on output variables. Response surface methodology was employed to predict the results of flexural strength 48.2910 MPa and surface roughness 3.5826 µm with an optimal setting of parameters of 0.14-mm layer thickness and 100% infill density along with horizontal build orientation. Experimental results confirm infill density and build orientation as highly significant parameters for impacting flexural strength and surface roughness, respectively.

Effect of layer thickness on irreversible thermal expansion and interlayer strength in fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 943-953 ◽  
Author(s):  
Anthony A. D’Amico ◽  
Analise Debaie ◽  
Amy M. Peterson
Keyword(s):  
Mechanical Properties ◽  
Thermal Expansion ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Thermal Strain ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact

Purpose The aim of this paper is to examine the impact of layer thickness on irreversible thermal expansion, residual stress and mechanical properties of additively manufactured parts. Design/methodology/approach Samples were printed at several layer thicknesses, and their irreversible thermal expansion, tensile strength and flexural strength were determined. Findings Irreversible thermal strain increases with decreasing layer thickness, up to 22 per cent strain. Tensile and flexural strengths exhibited a peak at a layer thickness of 200 μm although the maximum was not statistically significant at a 95 per cent confidence interval. Tensile strength was 54 to 97 per cent of reported values for injection molded acrylonitrile butadiene styrene (ABS) and 29 to 73 per cent of those reported for bulk ABS. Flexural strength was 18 to 41 per cent of reported flexural strength for bulk ABS. Practical implications The large irreversible thermal strain exhibited that corresponding residual stresses could lead to failure of additively manufactured parts over time. Additionally, the observed irreversible thermal strains could enable thermally responsive shape in additively manufactured parts. Variation in mechanical properties with layer thickness will also affect manufactured parts. Originality/value Tailorable irreversible thermal strain of this magnitude has not been previously reported for additively manufactured parts. This strain occurs in parts made with both high-end and consumer grade fused deposition modeling machines. Additionally, the impact of layer thickness on tensile and flexural properties of additively manufactured parts has received limited attention in the literature.

Bonding quality and fracture analysis of polyamide 12 parts fabricated by fused deposition modeling

2017 ◽  
Vol 23 (6) ◽  
pp. 973-982 ◽  
Author(s):  
Hao Li ◽  
Shuai Zhang ◽  
Zhiran Yi ◽  
Jie Li ◽  
Aihua Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Rheological Properties ◽  
Fused Deposition Modeling ◽  
Mechanical Performance ◽  
Melt Viscosity ◽  
Bonding Quality ◽  
Content Type ◽  
Polyamide 12 ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose This work aims to evaluate the influence of rheological properties of building materials on the bonding quality and ultimate tensile strength in the fused deposition modeling (FDM) process, through the investigation of parts printed by semi-crystalline and amorphous resins. Little information is currently available about the influence of the crystalline nature on FDM-printed part quality. Design/methodology/approach Semi-crystalline polyamide 12 and amorphous acrylonitrile butadiene styrene (ABS) were used to assess the influence of rheological properties on bonding quality and the tensile strength, by varying three important process parameters: materials, liquefier temperature and raster orientation. A fractography of both tensile and freeze-fractured samples was also investigated. Findings The rheological properties, mainly the melt viscosity, were found to have a significant influence on the bonding quality of fused filaments. Better bonding quality and higher tensile strength of FDM parts printed with semi-crystalline PA12, as compared with amorphous ABS, are suggested to be a result of higher initial sintering rates owing to the lower melt viscosity of PA12 at low shear rates. Near-full dense PA12 parts were obtained by FDM. Originality/value This project provides a variety of data and insight regarding the effect of materials properties on the mechanical performance of FDM-printed parts. The results showed that FDM technique allows the production of PA12 parts with adequate mechanical performance, overcoming the greatest limitation of a dependence on amorphous thermoplastics as a feedstock for the production of prototypes.

Improvement in Tensile Strength of FDM Built Parts by Parametric Control

2014 ◽  
Vol 592-594 ◽  
pp. 1075-1079 ◽  
Author(s):  
Swayam Bikash Mishra ◽  
Siba Sankar Mahapatra
Keyword(s):  
Tensile Strength ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Optimal Parameter ◽  
Layer By Layer ◽  
3D Objects ◽  
Fused Deposition ◽  
Solid Models ◽  
Raster Angle ◽  
Deposition Modeling

Fused Deposition Modeling (FDM) is one of the efficient rapid prototyping (RP) technologies that forms 3D objects by adding material layer by layer from CAD generated solid models. However, the FDM built part is hardly anisotropic in nature due to layer-by-layer build mechanism. Literature suggests that mechanical property, especially tensile strength, of FDM built part is severely affected by process parameters. Among all the parameters, contour number happens to be an important parameter because it reduces stress concentration resulting in avoidance of premature breakdown. Therefore, in this work contour number along with five important process parameters such as layer thickness, raster width, part orientation, raster angle and air gap are considered and their effect on tensile strength of FDM built parts is studied. Experiments are conducted using Face Centred Central Composite Design (FCCCD) in order to reduce the experimental runs. An optimal parameter setting has been suggested for the maximisation of tensile strength of the FDM built parts.

scholarly journals Additive Manufacturing of Wood Flour/PHA Composites Using Micro-Screw Extrusion: Effect of Device and Process Parameters on Performance

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1107
Author(s):  
Jing Tian ◽  
Run Zhang ◽  
Jiayuan Yang ◽  
Weimin Chou ◽  
Ping Xue ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Wood Flour ◽  
Screw Speed ◽  
Fused Deposition ◽  
Screw Extrusion ◽  
Deposition Modeling ◽  
Influencing Parameters ◽  
Printing Speed

Based on additive manufacturing of wood flour and polyhydroxyalkanoates composites using micro-screw extrusion, device and process parameters were evaluated to achieve a reliable printing. The results show that the anisotropy of samples printed by micro-screw extrusion is less obvious than that of filament extrusion fused deposition modeling. The type of micro-screw, printing speed, layer thickness, and nozzle diameter have significant effects on the performance of printed samples. The linear relationship between the influencing parameters and the screw speed is established, therefore, the performance of printed products can be controlled by the extrusion flow rate related to screw speed.

scholarly journals Influence of Process Parameters on Tensile Strength of Additive Manufactured PLA Parts using Taguchi Method

2019 ◽  
Vol 8 (3) ◽  
pp. 7635-7639
Keyword(s):  
Tensile Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Optimal Parameter ◽  
Fused Filament Fabrication ◽  
Influence Of Process Parameters ◽  
Layer Height ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Nozzle Temperature

Influence of layer thickness nozzle temperature and angle on tensile strength of PLA fabricated with FDM (FFF) was experimentally investigated. Polylactic Acid (PLA) is a semi-crystalline and bio-friendly thermoplastic polymer has identified as important material in different applications due to its mechanical characteristics. Fused Deposition Modeling (FDM) is a one of the proved technology in Fused Filament Fabrication (FFF) technique in additive manufacturing process. In present investigation different specimens were fabricated using FDM technique with different layer height and different layer angles for finding influence of these manufacturing parameters on tensile strength of the specimen. Specimens were fabricated and tested as per ASTM D638 standard. It is clearly observed that tensile strength is more for +450 /-450 layer angle than the +00 /-0 0 layer angle for a given layer height(h=0.10 mm, h=0.15mm and h=0.20mm).The TAGUCHI analysis is carried with nozzle temperature, layer thickness and angle finding optimal values. It has been observed that, the optimal parameter is angle, which is equal to 30 0 .the ANOVA variation of angle layer with tensile strength has been observed that 18.10-31.90.

Sign in / Sign up

Export Citation Format

Share Document