scholarly journals Investigation of the Deformation Behaviour and Resulting Ply Thicknesses of Multilayered Fibre–MetalFibreM Laminates

2021 ◽  
Vol 5 (7) ◽  
pp. 176
Author(s):  
Missam Irani ◽  
Moritz Kuhtz ◽  
Mathias Zapf ◽  
Madlen Ullmann ◽  
Andreas Hornig ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Deformation Behaviour ◽  
Element Model ◽  
Light Metal ◽  
Processing Temperature ◽  
Forming Process ◽  
Element Analysis ◽  
Reinforced Plastics ◽  
Thermoelastic Plastic

Multilayered fibre–metal laminates (FMLs) are composed of metal semifinished products and fibre-reinforced plastics, and benefit from the advantages of both material classes. Light metals in combination with fibre-reinforced thermoplastics are highly suitable for mass production of lightweight structures with good mechanical properties. As the formability of light metal sheets is sometimes limited at room temperature, increasing the process temperature is an appropriate approach to improve formability. However, the melting of thermoplastic materials and resulting loss of stiffness limit the processing temperature. Since single-ply layers have different through-thickness stiffnesses, the forming process changes the ply thickness of the multilayered laminate. In the present study, the deformation behaviour of multilayered FMLs was investigated using a two-dimensional finite-element model assuming plane strain. The thermoelastic-plastic finite-element analysis made investigation of the variation in thickness made possible by incorporating sufficient mesh layers in the thickness direction. The results indicate that a thermoelastic-plastic finite-element model can predict the delamination of plies during deformation, as well as in the final product. Additionally, the predicted changes in thickness of the plies are in good agreement with experimental results when a temperature-dependent friction coefficient is used.

Sheet Metals Forming Die Design Using Finite Element Analysis and the Taguchi Method

2014 ◽  
Vol 621 ◽  
pp. 195-201
Author(s):  
Surangsee Dechjarern ◽  
Maitri Kamonrattanapisut
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Coefficient ◽  
Taguchi Method ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Element Model ◽  
Die Design ◽  
Forming Process ◽  
Element Analysis

Sheet metal deep-draw die is primarily constructed with draw bead, which is then modified based on trial and error to obtain a successful forming without splitting. This work aims at a robust design of forming die using numerical analysis and the Taguchi method. A three dimensional elastoplastic finite element model of a sheet metal forming process of SPCEN steel has been successfully developed using the material flow stress obtained from the modified Erichsen cup test. The model was validated with the actual forming experiment and the results agreed well. The influence of draw bead parameters on splitting and thinning distributions were examined using the Taguchi method. Four parameters, namely the friction coefficient, draw bead height, radius and shoulder radius were investigated. The Taguchi main effect analysis and ANOVA results show that the height and shoulder radius of the draw bead are the most important factor influencing the thinning distribution. Applying the Taguchi method and using the minimum thinning percentage as the design criteria, the optimum die design was identified as height, radius, shoulder radius and the friction coefficient of 4, 8, 8 mm and 0.125 respectively. The verified finite element model using the optimum die design was conducted. The predicted Taguchi response was within 5.9% from finite element analysis prediction. The improvement in the reduction of thinning percentage was 22.35%.

The Significance of Experiment in the Finite Element Analysis of a Pulley Forming Process

2005 ◽  
Vol 6-8 ◽  
pp. 615-622
Author(s):  
Xiao Hang Liu ◽  
Mike Daniels ◽  
Bez Shirvani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Numerical Models ◽  
Metal Flow ◽  
Element Model ◽  
Axial Loads ◽  
Forming Process ◽  
Element Analysis ◽  
Forming Tools ◽  
The Finite Element Model

For reasons of cost and weight, light gauge sheet is used wherever possible for metal fabrications. In sheet metal forming the process is to gather the metal into defined areas. The pulley forming process is no exception and is achieved by superimposing axial loads on top of radial loads using a pressure-controlled tailstock. Whilst the headstock-mounted tooling is fixed, that part held on the tailstock can be powered axially under controlled pressure. This pressure is governed by the width of the workpiece which changes during the forming process. Experiments have been designed to provide an understanding of the pulley forming process and to verify numerical models. The latter has been taken the form of finite element simulations to enable prediction of metal flow, tool forces and potential sources of defects and failures. There are three objectives for conducting the experiments which have been investigated in this paper: 1. providing data to define the movements of the forming tools for the finite element model, including displacements and velocities, 2. understanding the effects of the pulley forming operation on the flow of material, and 3. validating the finite element model.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

scholarly journals A Novel Method for Tooth Bending Stress Calculation of Gears With Asymmetric Teeth

2021 ◽  
Author(s):  
Oguz DOGAN ◽  
Celalettin YUCE ◽  
Fatih KARPAT
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Experimental Studies ◽  
Element Model ◽  
Bending Stress ◽  
Element Analysis ◽  
Stress Calculation ◽  
Bending Stresses ◽  
New Equation ◽  
Asymmetric Factor

Abstract Today, gear designs with asymmetric tooth profiles offer essential solutions in reducing tooth root stresses of gears. Although numerical, analytical, and experimental studies are carried out to calculate the bending stresses in gears with asymmetric tooth profiles a standard or a simplified equation or empirical statement has not been encountered in the literature. In this study, a novel bending stress calculation procedure for gears with asymmetric tooth profiles is developed using both the DIN3990 standard and the finite element method. The bending stresses of gears with symmetrical profile were determined by the developed finite element model and was verified by comparing the results with the DIN 3990 standard. Using the verified finite element model, by changing the drive side pressure angle between 20° and 30° and the number of teeth between 18 and 100, 66 different cases were examined and the bending stresses in gears with asymmetric profile were determined. As a result of the analysis, a new asymmetric factor was derived. By adding the obtained asymmetric factor to the DIN 3390 formula, a new equation has been derived to be used in tooth bending stresses of gears with asymmetric profile. Thanks to this equation, designers will be able to calculate tooth bending stresses with high precision in gears with asymmetric tooth profile without the need for finite element analysis.

Simulation of Thermo-Mechanical Models for Hot Formed Parts by Numerical Experiments

2014 ◽  
Vol 663 ◽  
pp. 668-674
Author(s):  
Azman Senin ◽  
Zulkifli Mohd Nopiah ◽  
Muhammad Jamhuri Jamaludin ◽  
Ahmad Zakaria
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Prediction Accuracy ◽  
Research Work ◽  
Deformation Characteristic ◽  
Element Model ◽  
Forming Limit ◽  
Prototype Model ◽  
New Production ◽  
Element Analysis

The Finite-Element Analysis (FEA) is a prediction methodology that facilitates product designers produced the part design with manufacturing focused. With the similar advantages, manufacturing engineers are capable of build the first actual car model from the new production Draw Die. This approach has eliminated the requirement to manufacture the prototype model from soft tool parts and soft tool press die. However, the prediction accuracy of FEA is a major topic of research work in automotive sector's practitioners and academia as current accuracy level is anticipated at 60%. The objective of works is to assess the prediction accuracy on deformation results from mass production stamped parts. The Finite-element model is developed from the CAD data of the production tools. Subsequently, finite-element model for production tools is discretized with shell elements to avoid computation errors in the simulation process. The sheet blank material with 1.5 mm and 2.0 mm thickness is discredited by shell (2D modeling) and solid elements (3D modeling) respectively. The input parameters for the simulation model for both elements are attained from the actual setup at Press Machine and Production Tool. The analysis of deformation and plastic strain are performed for various setup parameters. Finally, the deformation characteristic such as Forming Limit Diagram (FLD) and thinning are compared for all simulated models.

Finite Element Analysis of Tandem Rubber O-Ring Sealing Structure at the End of Shaft

2013 ◽  
Vol 774-776 ◽  
pp. 25-29
Author(s):  
Cong Fang Hu ◽  
Yuan Qiang Tan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Compression Rate ◽  
Element Analysis ◽  
Uniform Compression ◽  
Friction Factors ◽  
Sealing Performance ◽  
Sealing Failure

Based on the tandem sealing structure at the end of the shaft,a finite element model of rubber O-rings has been established and the sealing performance of rubber O-ring has been analyzed. There is an un-uniform compression among these O-rings which lead to the sealing failure. Under different friction factors, several groups of the rubber O-rings have been analyzed, finding that the friction factor is the reason of un-uniform compression. The effect of different average compression rate has been investigated, which has been integrated in the sealing criteria for the tandem O-rings, providing a reference for the optimization of tandem sealing structure at the end of the shaft. According to the sealing criteria for a single O-ring, the sealing criteria for the tandem O-rings is built.

Finite Element Analysis of Mechanics Property on Memory Alloy Patella Claws with Anti-Shearing Force

2014 ◽  
Vol 635-637 ◽  
pp. 507-510
Author(s):  
Dong Peng Du ◽  
Zhe Wu ◽  
Juan Xing ◽  
Xiao Yan Gong ◽  
Xiang Wen Miu ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Mechanical Performance ◽  
Tensile Force ◽  
Research Result ◽  
Element Model ◽  
3D Models ◽  
Shearing Force ◽  
Maximum Displacement ◽  
Element Analysis

When strong exercise on human being body, respectively, under knees 30°, 60°,90°, using PRO/E5.0 software to establish the transverse patella fracture and anti-shearing force patella claws 3D models, then the two structure models were assembled and imported into ABAQUS10.1 software to establish the finite element model of patellar fracture fixed within patella claw, and analyzed the mechanical performance in perforce finite element model. Under the same boundary conditions, the maximum displacement and deformation of each components were different at every flexion angle. Compared with anti-shearing force patella claw and AO tensile force girdle, the patella claw with stronger resistance to tension and anti-shearing force was more stable. Deformation and displacement of patella claw in accordance with biomechanical research result that is needed by clinical. Its stability will satisfy clinical requirements for functional exercise.

Sign in / Sign up

Export Citation Format

Share Document