scholarly journals NEURAP—A Dedicated Neutron-Imaging Facility for Highly Radioactive Samples

2021 ◽  
Vol 7 (3) ◽  
pp. 57
Author(s):  
Eberhard Lehmann ◽  
Knud Thomsen ◽  
Markus Strobl ◽  
Pavel Trtik ◽  
Johannes Bertsch ◽  
...  
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Image Data ◽  
Neutron Imaging ◽  
Imaging Plate ◽  
Spent Fuel ◽  
Radiation Background ◽  
Special Configuration ◽  
Term Operation ◽  
Neutron Spallation Source

NEURAP is a dedicated set-up at the Swiss neutron spallation source (SINQ) at the Paul Scherrer Institut (PSI), optionally implemented as a special configuration of the neutron-imaging station NEUTRA. It is one of very few instrumentations available worldwide enabling neutron-imaging of highly radioactive samples to be performed routinely, with special precautions and following a specific procedure. Since the relevant objects are strong γ-sources, dedicated techniques are needed to handle the samples and to perform neutron-imaging despite the radiation background. Dysprosium (Dy)-loaded imaging plates, effectively made sensitive to neutrons only, are employed. Neutrons are captured by Dy during neutron irradiation. Then the imaging plate is erased removing gamma detections. A subsequent relatively long self-exposure by the radiation from the intrinsic neutron-activated Dy within the imaging plate yields the neutron-only radiograph that is finally read out. During more than 20 years of NEURAP operation, images have been obtained for two major applications: (a) highly radioactive SINQ target components were investigated after long-term operation life; and (b) spent fuel rods and their cladding from Swiss nuclear power plants were characterized. Quantitative analysis of the image data demonstrated the accumulation of spallation products in the lead filled “Cannelloni” Zircaloy tubes of the SINQ target and the aggregation of hydrogen at specific sites in used fuel pins of power plants and their cladding, respectively. These results continue to help understanding material degradation and optimizing the operational regimes, which might lead to extending the safe lifetimes of these components.

scholarly journals Demonstration of Fatigue for LTO License of NPP Borssele

2015 ◽  
Author(s):  
M. H. C. Hannink ◽  
F. J. Blom ◽  
P. W. B. Quist ◽  
A. E. de Jong ◽  
W. Besuijen
Keyword(s):  
Environmental Effects ◽  
Nuclear Power ◽  
Power Plants ◽  
Integrated Approach ◽  
Temperature Measurements ◽  
Fatigue Assessment ◽  
Term Operation ◽  
Load Monitoring ◽  
Number Of Cycles ◽  
Ageing Management

Long Term Operation (LTO) of nuclear power plants (NPPs) requires an ageing management review and a revalidation of Time Limited Ageing Analyses (TLAAs) of structures and components important for nuclear safety. An important ageing effect to manage is fatigue. Generally, the basis for this is formed by the fatigue analyses of the safety relevant components. In this paper, the methodology for the revalidation of fatigue TLAAs is demonstrated for LTO of NPP Borssele in the Netherlands. The LTO demonstration starts with a scoping survey to determine the components and locations having relevant fatigue loadings. The scope was defined by assessment against international practice and guidelines and engineering judgment. Next, a methodical review was performed of all existing fatigue TLAAs. This also includes the latest international developments regarding environmental effects. In order to reduce conservatism, a comparison was made between the number of cycles in the analyses and the number of cycles projected to the end of the intended LTO period. The projected number of cycles is based on transient counting. The loading conditions used in the analyses were assessed by means of temperature measurements by the fatigue monitoring system (FAMOS). As a result of the review, further fatigue assessment or assessment of environmental effects was necessary for certain locations. New analyses were performed using state-of-the-art calculation and assessment methods. The methodology is demonstrated by means of an example of the surge line. The model includes the piping, as well as the nozzles on the pressurizer and the main coolant line. The thermal loadings for the fatigue analysis are based on temperature measurements. Fatigue management of the NPP is ensured by means of the fatigue concept where load monitoring, transient counting and fatigue assessment are coupled through an integrated approach during the entire period of LTO.

NUCLEAR WASTE MANAGEMENT IN SPAIN: ANALYSIS OF THE CURRENT SITUATION AND ALTERNATIVE STRATEGIES

10.6036/10156 ◽  
2021 ◽  
Vol 96 (4) ◽  
pp. 355-358
Author(s):  
Pablo Fernández Arias ◽  
DIEGO VERGARA RODRIGUEZ
Keyword(s):  
Nuclear Waste ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Spent Fuel ◽  
Nuclear Waste Storage ◽  
Alternative Strategies ◽  
Temporary Storage ◽  
Long Term Storage ◽  
High Level

Centralized Temporary Storage Facility (CTS) is an industrial facility designed to store spent fuel (SF) and high level radioactive waste (HLW) generated at Spanish nuclear power plants (NPP) in a single location. At the end of 2011, the Spanish Government approved the installation of the CTS in the municipality of Villar de Cañas in Cuenca. This approval was the outcome of a long process of technical studies and political decisions that were always surrounded by great social rejection. After years of confrontations between the different political levels, with hardly any progress in its construction, this infrastructure of national importance seems to have been definitively postponed. The present research analyzes the management strategy of SF and HLW in Spain, as well as the alternative strategies proposed, taking into account the current schedule foreseen for the closure of the Spanish NPPs. In view of the results obtained, it is difficult to affirm that the CTS will be available in 2028, with the possibility that its implementation may be delayed to 2032, or even that it may never happen, making it necessary to adopt an alternative strategy for the management of GC and ARAR in Spain. Among the different alternatives, the permanence of the current Individualized Temporary Stores (ITS) as a long-term storage strategy stands out, and even the possibility of building several distributed temporary storage facilities (DTS) in which to store the SF and HLW from several Spanish NPP. Keywords: nuclear waste, storage, nuclear power plants.

scholarly journals Temperature conditions in the RBMK spent fuel pool in the event of disturbances in its cooling mode

2021 ◽  
Vol 7 (1) ◽  
pp. 9-13
Author(s):  
David A. Hakobyan ◽  
Victor I. Slobodchuk
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Spent Nuclear Fuel ◽  
Maximum Temperature ◽  
Spent Fuel ◽  
Cooling Mode ◽  
Temperature Conditions ◽  
Fuel Assemblies ◽  
Spent Fuel Pool

The problems of reprocessing and long-term storage of spent nuclear fuel (SNF) at nuclear power plants with RBMK reactors have not been fully resolved so far. For this reason, nuclear power plants are forced to search for new options for the disposal of spent fuel, which can provide at least temporary SNF storage. One of the possible solutions to this problem is to switch to compacted SNF storage in reactor spent fuel pools (SFPs). As the number of spent fuel assemblies (SFAs) in SFPs increases, a greater amount of heat is released. In addition, no less important is the fact that a place for emergency FA discharging should be provided in SFPs. The paper presents the results of a numerical simulation of the temperature conditions in SFPs both for compacted SNF storage and for emergency FA discharging. Several types of disturbances in normal SFP cooling mode are considered, including partial loss of cooling water and exposure of SFAs. The simulation was performed using the ANSYS CFX software tool. Estimates were made of the time for heating water to the boiling point, as well as the time for heating the cladding of the fuel elements to a temperature of 650 °С. The most critical conditions are observed in the emergency FA discharging compartment. The results obtained make it possible to estimate the time that the personnel have to restore normal cooling mode of the spent fuel pool until the maximum temperature for water and spent fuel assemblies is reached.

Qualification Requirements Design for Neutron Absorber Plate for Spent Fuel Racks in Domestic Nuclear Power Plants

2019 ◽  
Vol 5 (3) ◽  
Author(s):  
You Shi ◽  
Dong Ning ◽  
Yi-zhong Yang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Aluminum Matrix ◽  
Practical Significance ◽  
Spent Fuel ◽  
Absorber Plate ◽  
Neutron Absorber ◽  
Fuel Storage ◽  
B4c Particle

Boron carbide (B4C) particle-reinforced aluminum matrix composite is the key material for use as neutron absorber plate in fuel storage applications for Generation III advanced passive nuclear power plants in China. This material has once depended upon importing with various restrictions so that it has meaningful practical significance to realize the localized manufacturing for this material in China. More importantly, since it is the first time for this material to be used in domestic plant, particular care should be taken to assure the formal supplied products exhibit high stabilized and reliable service in domestic nuclear engineering. This paper initiates and proposes a principle design framework from technical view in qualification requirements for this material so as to guide the practical engineering application. Aiming at neutron absorber materials supplied under practical manufacturing condition in engineering delivery, the qualification requirements define B4C content, matrix chemistry, 10B isotope, bulk density, 10B areal density, mechanical property, and microstructure as key criteria for material performance. The uniformity assessment as to different locations of this material is also required from at least three lots of material. Only qualified material meeting all of the qualification requirements should proceed to be verified by lifetime testing such as irradiation, corrosion, and thermal aging testing. Systematic and comprehensive performance assessments and verification for process stabilization could be achieved through the above qualification. The long-term service for this neutron absorber material in reliable and safe way could be convincingly expected in spent fuel storage application in China.

Guided Waves as an Online Monitoring Technology for Long-Term Operation in Nuclear Power Plants: Experimental Results on a Steam Discharge Pipe

2019 ◽  
Vol 5 (1) ◽  
Author(s):  
Mauro Cappelli ◽  
Francesco Cordella ◽  
Francesco Bertoncini ◽  
Marco Raugi
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Guided Waves ◽  
Complex Structure ◽  
Theoretical Background ◽  
Guided Wave ◽  
Experimental Results ◽  
Term Operation

Guided wave (GW) testing is regularly used for finding defect locations through long-range screening using low-frequency waves (from 5 to 250 kHz). By using magnetostrictive sensors, some issues, which usually limit the application to nuclear power plants (NPPs), can be fixed. The authors have already shown the basic theoretical background and simulation results concerning a real steel pipe, used for steam discharge, with a complex structure. On the basis of such theoretical framework, a new campaign has been designed and developed on the same pipe, and the obtained experimental results are now here presented as a useful benchmark for the application of GWs as nondestructive techniques. Experimental measures using a symmetrical probe and a local probe in different configurations (pulse-echo and pitch-catch) indicate that GW testing with magnetostrictive sensors can be reliably applied to long-term monitoring of NPPs components.

scholarly journals Reactor performance, system reliability, instrumentation and control

2020 ◽  
Vol 6 ◽  
pp. 43
Author(s):  
Andreas Schumm ◽  
Madalina Rabung ◽  
Gregory Marque ◽  
Jary Hamalainen
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Lessons Learned ◽  
Software Systems ◽  
Reactor Performance ◽  
Horizon 2020 ◽  
Term Operation ◽  
In The Beginning ◽  
Electrical Cables

We present a cross-cutting review of three on-going Horizon 2020 projects (ADVISE, NOMAD, TEAM CABLES) and one already finished FP7 project (HARMONICS), which address the reliability of safety-relevant components and systems in nuclear power plants, with a scope ranging from the pressure vessel and primary loop to safety-critical software systems and electrical cables. The paper discusses scientific challenges faced in the beginning and achievements made throughout the projects, including the industrial impact and lessons learned. Two particular aspects highlighted concern the way the projects sought contact with end users, and the balance between industrial and academic partners. The paper concludes with an outlook on follow-up issues related to the long term operation of nuclear power plants.

Transmutation and the Global Nuclear Energy Partnership

2006 ◽  
Vol 985 ◽  
Author(s):  
James Bresee
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Energy ◽  
Energy Use ◽  
Fuel Cycle ◽  
Spent Fuel ◽  
Closed Fuel Cycle ◽  
State Of The Union ◽  
Foreign Countries ◽  
The U.S

AbstractIn the January 2006 State of the Union address, President Bush announced a new Advanced Energy Initiative, a significant part of which is the Global Nuclear Energy Initiative. Its details were described on February 6, 2006 by the U.S. Secretary of Energy. In summary, it has three parts: (1) a program to expand nuclear energy use domestically and in foreign countries to support economic growth while reducing the release of greenhouse gases such as carbon dioxide. (2) an expansion of the U.S. nuclear infrastructure that will lead to the recycling of spent fuel and a closed fuel cycle and, through transmutation, a reduction in the quantity and radiotoxicity of nuclear waste and its proliferation concerns, and (3) a partnership with other fuel cycle nations to support nuclear power in additional nations by providing small nuclear power plants and leased fuel with the provision that the resulting spent fuel would be returned by the lessee to the lessor. The final part would have the effect of stabilizing the number of fuel cycle countries with attendant non-proliferation value. Details will be given later in the paper.

Operational Experience of TN 24 Dual Purpose Spent Fuel Storage Casks at the DOEL Nuclear Power Plants in Belgium

2001 ◽  
Author(s):  
C. Baroux ◽  
M. Detrilleaux ◽  
G. Demazy
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Spent Nuclear Fuel ◽  
High Capacity ◽  
Radiation Shielding ◽  
Ring Closure ◽  
Operational Experience ◽  
Spent Fuel ◽  
Dual Purpose ◽  
New Members

Abstract Spent nuclear fuel has been stored at the DOEL power station in Belgium in dual-purpose metal casks since 1995. The casks were procured from TRANSNUCLEAIRE by SYNATOM to meet the operational demands for on-site dry storage solutions for fuel arising from the four PWR reactors at DOEL. The TN 24 type of cask was chosen and a range of different cask types were developed. The initial requirement was for dual purpose cask to contain fuel from the DOEL units 3 and 4, these having similar fuel types but different lengths, and thus two new members of the TN 24 family were developed; the TN 24 D and TN 24 XL with capacities of 28 and 24 SFA’s. These casks were licensed as B(U) fissile packagings with approval certificates granted by the French and validated by the Belgium competent authorities for the transport configurations. Both cask designs were also analyzed by TRANSNUCLEAIRE in their storage configurations to ensure that the criteria for safe interim storage could be met. Since 1995, a total of 18 TN 24 D and TN 24 XL casks have been loaded with spent fuel assemblies with an average burn-up of 40,000 MWd/tU. SYNATOM subsequently decided to purchase further casks for DOEL 3 and 4 fuels with higher enrichments, higher burn-ups and shorter cooling times. TRANSNUCLEAIRE developed the TN 24 DH and TN 24 XLH casks within the similar envelope size and weight limits. The increase in performance was achieved by an in-depth optimization of each design in terms of radiation shielding, heat transfer and criticality safety. This paper shows how this optimization process was undertaken for the TN 24 DH and TN 24 XLH casks, 16 of which have been ordered by SYNATOM. DOEL 1 and 2 units use much shorter PWR fuel and it was decided to ship the fuel to unit 3 with an internal transfer cask because the handling limitations in the DOEL 1 and 2 pool prohibited the loading of a high capacity dual purpose transport/storage cask. The TN 24 SH cask was subsequently designed for DOEL 1 and 2 PWR fuel with a capacity of 37 assemblies and nine of there casks have been ordered by SYNATOM. The casks are fitted with monitoring devices to detect any change in the performance of the double metal O ring closure system and none of the casks has shown any deterioration in leaktightness. This paper examines the operation experience of loading and storing more than 30 TN 24 dual purpose casks and compares the performance with design expectations.

Study on the Impact Limiter Design in Spent Fuel Transfer Cask in Nuclear Power Plants

2020 ◽  
Author(s):  
Yuchen Hao ◽  
Yue Li ◽  
Jinhua Wang ◽  
Bin Wu ◽  
Haitao Wang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Theoretical Method ◽  
Structure Design ◽  
Design Approach ◽  
Spent Fuel ◽  
Typical Structure ◽  
Explicit Finite Element ◽  
The Impact

Abstract In nuclear power plants, the amount of spent fuel stored on-site is limited. Therefore, it is necessary to be shipped to off-site storage or disposal facilities regularly. The key risk in the transfer of spent fuel involves a release of radiation that could cause harmful effects to people and the environment. Transfer casks with impact limiters on both ends are always employed to ensure safe containment of radioactive materials, which should be verified by the 9 meters drop test onto an unyielding surface according to IAEA SSR-6. In this paper, we focus on the influence of the impact-limiter parameters, including geometry dimensions and mechanical properties, on the results of drop events to achieve an optimized approach for design. The typical structure of impact limiter is bulk energy-absorbed material wrapped by thin stainless-steel shells. Compared to traditional wood, foam has advantages of isotropy and steady quality. In this paper, theoretical and numerical methods are both adopted to investigate the influence of impact limiters during hypothetical accidental conditions for optimizing buffer influence and protecting the internal fuel components. First of all, a series of polyurethane foam is selected according to the theoretical method, because its mechanical property is related to density. Therefore, using explicit finite element method to investigate the influence of parameters of foam in impact limiter. These discrete points from the above result can be utilized to establish damage curves by date fitting. Finally, a design approach for spent fuel transfer cask is summarized, to provide a convenient formula to predict the damage and optimize structure design in drop condition. Furthermore, this design approach can be applied in the multi-module shared system of SNF, which can contain different fuel assemblies.

Sign in / Sign up

Export Citation Format

Share Document