scholarly journals Material Analysis and Molecular Dynamics Simulation for Cavitation Erosion and Corrosion Suppression in Water Hydraulic Valves

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 453 ◽  
Author(s):  
Masoud Kamoleka Mlela ◽  
He Xu ◽  
Feng Sun ◽  
Haihang Wang ◽  
Gabriel Donald Madenge
Keyword(s):  
Molecular Dynamics ◽  
Md Simulation ◽  
Essential Role ◽  
Corrosion Inhibitors ◽  
Cavitation Erosion ◽  
Dynamics Simulation ◽  
Preference Ranking ◽  
Water Hydraulics ◽  
The Impact ◽  
Hydraulic Valves

In the milestone of straggling to make water hydraulics more advantageous, the choice of coating polymer for water hydraulics valves plays an essential role in alleviating the impact of cavitation erosion and corrosion, and this is a critical task for designers. Fulfilling the appropriate selection, we conflicted properties that are vital for erosion and corrosion inhibitors, as well as the tribology in the sense of coefficient of friction. This article aimed to choose the best alternative polymer for coating on the selected substrate, that is, Cr2O3, Al2O3, Ti2O3. By applying PROMETHEE (Preference Ranking Organization Method for Enrichment Evaluations), the best polymer obtained with an analyzed performance attribute is Polytetrafluoroethylene (PTFE) that comes up with higher outranking (0.5932052). A Molecular Dynamics (MD) simulation was conducted to identify the stronger bonding with the regards of the better cleave plane between Polytetrafluoroethylene (PTFE) and the selected substrate. Polytetrafluoroethylene (PTFE)/Al2O3 cleaved in (010) plane was observed to be the strongest bond in terms of binding energy (3188 kJ/mol) suitable for further studies.

Molecular Dynamics Simulation of Shot Peening Process and Residual Stress Generation: Effects of Particle Impact Speed and Impinging Angle

2014 ◽  
Author(s):  
Yachao Wang ◽  
Jing Shi ◽  
Xinnan Wang
Keyword(s):  
Molecular Dynamics ◽  
Residual Stress ◽  
Stress Distribution ◽  
Shot Peening ◽  
Md Simulation ◽  
Stress Generation ◽  
Dynamics Simulation ◽  
Surface Finishing ◽  
In Situ Observation ◽  
The Impact

Shot peening is a well-known surface finishing process that is often applied to enhance the residual stress distribution in the component surfaces. In this study, we carry out a molecular dynamics (MD) simulation study to investigate the single particle shot peening process on the (100) silicon surface at nano scale. The MD simulation enables in-situ observation and analysis of complex material deformation mechanisms in the presences of ultra-high strain rate, such as stress distribution, dislocation propagation, and particle/workpiece interface interaction. Three levels of shot speed (i.e., 200, 500, and 800 m/s) and three levels of impinging angle (i.e., 30°, 60°, and 90°) are configured in the simulation. It is found that higher shot speeds result in deeper depths of residual indentation, deeper penetration depths of residual stress below surface, and higher magnitude of maximum compressive stress. The residual stress distributions underneath the shot-peened surfaces exhibit strong anisotropic manner. Residual stress only concentrates in the area along the impact direction; and the decrease of impact angle results in shallower penetration of residual stress.

scholarly journals The Impact of the Electric Field on Surface Condensation of Water Vapor: Insight from Molecular Dynamics Simulation

Nanomaterials ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 64 ◽  
Author(s):  
Qin Wang ◽  
Hui Xie ◽  
Zhiming Hu ◽  
Chao Liu
Keyword(s):  
Molecular Dynamics ◽  
Water Vapor ◽  
Electric Field ◽  
Intermolecular Forces ◽  
Dynamics Simulation ◽  
Water Molecules ◽  
Attraction Force ◽  
Condensation Rate ◽  
Shape Transformation ◽  
The Impact

In this study, molecular dynamics simulations were carried out to study the coupling effect of electric field strength and surface wettability on the condensation process of water vapor. Our results show that an electric field can rotate water molecules upward and restrict condensation. Formed clusters are stretched to become columns above the threshold strength of the field, causing the condensation rate to drop quickly. The enhancement of surface attraction force boosts the rearrangement of water molecules adjacent to the surface and exaggerates the threshold value for shape transformation. In addition, the contact area between clusters and the surface increases with increasing amounts of surface attraction force, which raises the condensation efficiency. Thus, the condensation rate of water vapor on a surface under an electric field is determined by competition between intermolecular forces from the electric field and the surface.

scholarly journals Molecular dynamics simulation of sI methane hydrate under compression and tension

2020 ◽  
Vol 18 (1) ◽  
pp. 69-76
Author(s):  
Qiang Wang ◽  
Qizhong Tang ◽  
Sen Tian
Keyword(s):  
Molecular Dynamics ◽  
Methane Hydrate ◽  
Fracture Process ◽  
Md Simulation ◽  
Maximum Stress ◽  
Dynamics Simulation ◽  
Tensile Fracture ◽  
Maximum Compressive Stress ◽  
Motion State ◽  
Stress States

AbstractMolecular dynamics (MD) analysis of methane hydrate is important for the application of methane hydrate technology. This study investigated the microstructure changes of sI methane hydrate and the laws of stress–strain evolution under the condition of compression and tension by using MD simulation. This study further explored the mechanical property and stability of sI methane hydrate under different stress states. Results showed that tensile and compressive failures produced an obvious size effect under a certain condition. At low temperature and high pressure, most of the clathrate hydrate maintained a stable structure in the tensile fracture process, during which only a small amount of unstable methane broke the structure, thereby, presenting a free-motion state. The methane hydrate cracked when the system reached the maximum stress in the loading process, in which the maximum compressive stress is larger than the tensile stress under the same experimental condition. This study provides a basis for understanding the microscopic stress characteristics of methane hydrate.

Molecular Dynamics Simulation of AFM-Based Nanomachining Processes

2011 ◽  
Author(s):  
Rapeepan Promyoo ◽  
Hazim El-Mounayri ◽  
Kody Varahramyan ◽  
Ashlie Martini
Keyword(s):  
Molecular Dynamics ◽  
Friction Coefficient ◽  
Md Simulation ◽  
Computational Models ◽  
Dynamics Simulation ◽  
Radius Of Curvature ◽  
Force Microscopy ◽  
Indentation Force ◽  
Atomic Force ◽  
Development And Validation

Recently, atomic force microscopy (AFM) has been widely used for nanomachining and fabrication of micro/ nanodevices. This paper describes the development and validation of computational models for AFM-based nanomachining (nanoindentation and nanoscratching). The Molecular Dynamics (MD) technique is used to model and simulate mechanical indentation and scratching at the nanoscale in the case of gold and silicon. The simulation allows for the prediction of indentation forces and the friction force at the interface between an indenter and a substrate. The effects of tip curvature and speed on indentation force and friction coefficient are investigated. The material deformation and indentation geometry are extracted based on the final locations of atoms, which are displaced by the rigid tool. In addition to modeling, an AFM was used to conduct actual indentation at the nanoscale, and provide measurements to validate the predictions from the MD simulation. The AFM provides resolution on nanometer (lateral) and angstrom (vertical) scales. A three-sided pyramid indenter (with a radius of curvature ∼ 50 nm) is raster scanned on top of the surface and in contact with it. It can be observed from the MD simulation results that the indentation force increases as the depth of indentation increases, but decreases as the scratching speed increases. On the other hand, the friction coefficient is found to be independent of scratching speed.

Molecular Dynamics Studies on the Growth and Structural Properties of Hydrogenated DLC Films

2008 ◽  
Vol 373-374 ◽  
pp. 108-112
Author(s):  
Yu Jun Zhang ◽  
Guang Neng Dong ◽  
Jun Hong Mao ◽  
You Bai Xie
Keyword(s):  
Molecular Dynamics ◽  
Structural Properties ◽  
Impact Energy ◽  
Frictional Coefficient ◽  
Carbon Films ◽  
Dynamics Simulation ◽  
Diamond Surface ◽  
Hydrogen Atoms ◽  
Molecular Configuration ◽  
The Impact

The novel frictional properties of hydrogenated DLC (Diamond-like Carbon) films have been reported for nearly ten years. But up to now, researchers still haven’t known the exact mechanism resulting in the super-low frictional performance of hydrogenated DLC films. Especially they have little knowledge on the molecular configuration and structural properties of these kinds of films. In this paper, CH3 radicals with different impact energies are selected as source species to deposit DLC films on diamond (100) by molecular dynamics simulation. Results show hydrogenated DLC films can be successfully obtained when impact energy is in an appropriate scope that is no less than 20eV. The depositing processes involve impinging diamond surface and bonding procedure. Some atoms, instead of bonding with substrate atoms, fly away from the diamond surface. Only suitable impact energy can improve the growth of the film. Within 30eV to 60eV, the maximum deposition ratio is attained. In addition, when carbon atoms act as the deposition sources, the deposition ratio is relatively higher. Furthermore, the authors find that species with higher concentration of carbon atoms in deposition sources lead to a better deposition rate. Carbon atoms are more reactive than hydrogen atoms. Then the relative densities of DLC films are calculated. The density curves indicate that the structures of the films vary obviously as the impact energy augments. The average relative density is generally monotone increase with the increment of impact energy. The hybridization of carbon atoms greatly affects the properties of hydrogenated DLC films. The transition between sp2 and sp3 will result in the graphitization and reduce the frictional coefficient when DLC films are used as tribo-pair in friction.

Molecular dynamics simulation of homogeneous nucleation of supersaturated potassium chloride (KCl) in aqueous solutions

CrystEngComm ◽  
2019 ◽  
Vol 21 (48) ◽  
pp. 7507-7518 ◽  
Author(s):  
Soroush Ahmadi ◽  
Yuanyi Wu ◽  
Sohrab Rohani
Keyword(s):  
Molecular Dynamics ◽  
Aqueous Solution ◽  
Molecular Dynamics Simulation ◽  
Aqueous Solutions ◽  
Potassium Chloride ◽  
Homogeneous Nucleation ◽  
Md Simulation ◽  
Crystal Nucleation ◽  
Dynamics Simulation

Molecular dynamics (MD) simulation is used to investigate the mechanism of crystal nucleation of potassium chloride (KCl) in a supersaturated aqueous solution at 293 K and 1 atm.

scholarly journals Molecular Dynamics Simulation and Kinetic Study of Fluoride Binding to V21C/V66C Myoglobin with a Cytoglobin-like Disulfide Bond

2020 ◽  
Vol 21 (7) ◽  
pp. 2512
Author(s):  
Lu-Lu Yin ◽  
Jia-Kun Xu ◽  
Xiao-Juan Wang ◽  
Shu-Qin Gao ◽  
Ying-Wu Lin
Keyword(s):  
Molecular Dynamics ◽  
Disulfide Bond ◽  
Rational Design ◽  
Double Mutant ◽  
Md Simulation ◽  
Experimental Studies ◽  
Heme Iron ◽  
Dynamics Simulation ◽  
Fluoride Ion ◽  
Artificial Proteins

Protein design is able to create artificial proteins with advanced functions, and computer simulation plays a key role in guiding the rational design. In the absence of structural evidence for cytoglobin (Cgb) with an intramolecular disulfide bond, we recently designed a de novo disulfide bond in myoglobin (Mb) based on structural alignment (i.e., V21C/V66C Mb double mutant). To provide deep insight into the regulation role of the Cys21-Cys66 disulfide bond, we herein perform molecular dynamics (MD) simulation of the fluoride–protein complex by using a fluoride ion as a probe, which reveals detailed interactions of the fluoride ion in the heme distal pocket, involving both the distal His64 and water molecules. Moreover, we determined the kinetic parameters of fluoride binding to the double mutant. The results agree with the MD simulation and show that the formation of the Cys21-Cys66 disulfide bond facilitates both fluoride binding to and dissociating from the heme iron. Therefore, the combination of theoretical and experimental studies provides valuable information for understanding the structure and function of heme proteins, as regulated by a disulfide bond. This study is thus able to guide the rational design of artificial proteins with tunable functions in the future.

Sign in / Sign up

Export Citation Format

Share Document